scholarly journals Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4692
Author(s):  
Daniel Chuchala ◽  
Jakub Sandak ◽  
Kazimierz A. Orlowski ◽  
Tomasz Muzinski ◽  
Marcin Lackowski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Yield Stress ◽  
Mechanical Performance ◽  
Process Analysis ◽  
Beech Wood ◽  
Drying Methods ◽  
Shear Yield Stress ◽  
Cutting Power ◽  
Shear Yield

The modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based on cutting process analysis is presented here. Two wood species (pine and beech) representing soft and hard woods were investigated with respect to four diverse drying methods used in industry. Fracture toughness and shear yield stress were determined directly from the cutting power signal that was recorded while frame sawing. An original procedure for compensation of the wood density variation is proposed to generalize mechanical properties of wood and allow direct comparison between species and drying methods. Noticeable differences of fracture toughness and shear yield stress values were found among all drying techniques and for both species, but only for beech wood the differences were statistically significant. These observations provide a new highlight on the understanding of the effect of thermo-hydro modification of wood on mechanical performance of structures. It can be also highly useful to optimize woodworking machines by properly adjusting cutting power requirements.

The shear and compressive yield stress of fibrillated acacia pulp fiber suspensions

2020 ◽  
Vol 35 (2) ◽  
pp. 243-250
Author(s):  
Jiulong Sha ◽  
Yueyue Yang ◽  
Can Wang ◽  
Wei Li ◽  
Peng Lu ◽  
...  
Keyword(s):  
Yield Stress ◽  
Paper Industry ◽  
Pulp Fiber ◽  
Fiber Suspensions ◽  
Fiber Morphology ◽  
Shear Yield Stress ◽  
Geometrical Properties ◽  
Compressive Yield Stress ◽  
Shear Yield ◽  
Fiber Cell Wall

AbstractThe degree of interactions between fibers and the tendency of fibers to form flocs play an important role in effective unit operation in pulp and paper industry. Mechanical treatments may damage the structure of the fiber cell wall and geometrical properties, and ultimately change the fiber-fiber interactions. In this study, the gel crowding number, compressive and shear yield stress of fibrillated acacia pulps were investigated, and the results showed that the gel crowding number of the refined pulp samples ranged from 8.7 to 10.7, which were much lower than that of un-refined pulps. As the concentration increased, both the compressive yield stress {P_{y}} and shear yield stress {\tau _{y}} of all suspensions increased accordingly, and the yield stress was found to depend on a power law of the crowding number. Moreover, the values of {\tau _{y}}/{P_{y}} were also examined and the variation of {\tau _{y}}/{P_{y}} became largely dependent on the fiber morphology and mass concentration.

Effect of toughened polyamide-coated carbon fiber fabric on the mechanical performance and fracture toughness of CFRP

2021 ◽  
pp. 002199832199945
Author(s):  
Jong H Eun ◽  
Bo K Choi ◽  
Sun M Sung ◽  
Min S Kim ◽  
Joon S Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Photoelectron Spectroscopy ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Internal Damage ◽  
Impact Tests ◽  
Flexural Tests ◽  
The Impact

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed. The mechanical properties of the carbon/epoxy composites, such as transverse flexural tests, longitudinal flexural tests, and impact tests, were investigated. After the impact tests, an ultrasonic C-scan was performed to reveal the internal damage area. The interlaminar fracture toughness of the carbon/epoxy composites was measured using a mode I test. The critical energy release rates were increased by 77% compared to the virgin carbon/epoxy composites. The surface morphology of the fractured surface was observed. The toughening mechanism of the carbon/epoxy composites was suggested based on the confirmed experimental data.

Shear yield stress of partially flocculated colloidal suspensions

AIChE Journal ◽  
1998 ◽  
Vol 44 (3) ◽  
pp. 538-544 ◽  
Author(s):  
Peter J. Scales ◽  
Stephen B. Johnson ◽  
Thomas W. Healy ◽  
Prakash C. Kapur
Keyword(s):  
Yield Stress ◽  
Colloidal Suspensions ◽  
Shear Yield Stress ◽  
Shear Yield

Comparison of mechanical properties of thermally modified wood at growth ring and cell wall level by means of instrumented indentation tests

Holzforschung ◽  
2009 ◽  
Vol 63 (4) ◽  
Author(s):  
Stefanie Stanzl-Tschegg ◽  
Wilfried Beikircher ◽  
Dieter Loidl
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Thermal Treatment ◽  
Mechanical Performance ◽  
Growth Ring ◽  
Beech Wood ◽  
Thermal Modification ◽  
Wood Structure ◽  
Instrumented Indentation ◽  
Indentation Tests

Abstract Thermal modification is a well established method to improve the dimensional stability and the durability for outdoor use of wood. Unfortunately, these improvements are usually accompanied with a deterioration of mechanical performance (e.g., reduced strength or higher brittleness). In contrast, our investigations of the hardness properties in the longitudinal direction of beech wood revealed a significant improvement with thermal modification. Furthermore, we applied instrumented indentation tests on different hierarchical levels of wood structure (growth ring and cell wall level) to gain closer insights on the mechanisms of thermal treatment of wood on mechanical properties. This approach provides a variety of mechanical data (e.g., elastic parameters, hardness parameters, and viscoelastic properties) from one single experiment. Investigations on the influence of thermal treatment on the mechanical properties of beech revealed similar trends on the growth ring as well as the on the cell wall level of the wood structure.

scholarly journals Improving the mechanical properties of commercial feldspathic dental porcelain by addition of Alumina-Zirconia

2019 ◽  
pp. 67-76
Author(s):  
Juliana Gómez ◽  
Astrid Rueda ◽  
Edgar Alexader Ossa Henao
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Contact Resistance ◽  
Mechanical Performance ◽  
Tetragonal Zirconia ◽  
Dental Ceramics ◽  
Aesthetic Response ◽  
Early Failure ◽  
Feldspathic Porcelain ◽  
Natural Tooth

Dental ceramics made from Yttria stabilized tetragonal Zirconia polycrystalline (Y-TZP) with feldspathic porcelain veneers have similar mechanical and aesthetic response to natural tooth. However, cases of early failure, such as chipping or fracture in the veneering have been reported after short periods of use. The present study evaluated the feldspathic porcelain (VITA-VM9) with addition of 0.5 and 2.5 wt% Alumina-Zirconia as reinforcing agents. Hardness, fracture toughness, contact resistance and color variations were evaluated finding better mechanical performance on the new formulations.

scholarly journals The Effects of Water and Seawater on the Mechanical Properties of Carbon Fibre Reinforced Epoxy Composite under Pre-Cure Curing Condition

1998 ◽  
Vol 7 (4) ◽  
pp. 096369359800700
Author(s):  
M. Zhang ◽  
S.E. Mason
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Carbon Fibre ◽  
Laminate Composite ◽  
Mechanical Performance ◽  
Epoxy Composite ◽  
Interlaminar Fracture Toughness ◽  
Curing Condition ◽  
Structural Carbon

The influences on the interlaminar fracture toughness (GIC) and ultimate tensile strength (UTS) of a cured structural carbon fibre reinforced epoxy composite of two contaminants, water and seawater, introduced prior to cure have been investigated. The results have demonstrated that the control of environmental factors such as water and seawater can have significant effects on the mechanical performance of laminate composite components during the manufacturing process.

Effect of reactive and non-reactive diluents on thermal and mechanical properties of epoxy resin

2017 ◽  
Vol 30 (10) ◽  
pp. 1159-1168 ◽  
Author(s):  
Animesh Sinha ◽  
Nazrul Islam Khan ◽  
Subhankar Das ◽  
Jiawei Zhang ◽  
Sudipta Halder
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Polyethylene Glycol ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Thermal And Mechanical Properties ◽  
Minor Variation ◽  
Reactive Diluents

The effect of reactive (polyethylene glycol) and non-reactive (toluene) diluents on thermal and mechanical properties (tensile strength, hardness and fracture toughness) of diglycidyl ether of bisphenol A epoxy resin (cured by triethylenetetramine) was investigated. The thermal stability and mechanical properties of the epoxy resin modified with reactive and non-reactive diluents at different wt% were investigated using thermo-gravimetric analyser, tensile test, hardness test and single-edge-notched bend test. A minor variation in thermal stability was observed for epoxy resin after addition of polyethylene glycol and toluene at 0.5 wt%; however, further addition of reactive and non-reactive diluents diminished the thermal stability. The addition of 10 wt% of polyethylene glycol in epoxy resin significantly enhances the tensile strength (∼12%), hardness (∼14%) and fracture toughness (∼24%) when compared to that of neat epoxy resin. In contrast, major drop in mechanical performance was observed after addition of toluene in epoxy. Furthermore, fracture surfaces were investigated under field emission scanning electron microscope to elucidate the failure mechanism.

Demonstration of Combined Shear and Squeeze Strengthening Modes in a Searle-Type Magnetorheometer

2013 ◽  
Author(s):  
Andrew C. Becnel ◽  
Norman M. Wereley
Keyword(s):  
Yield Stress ◽  
Energy Absorption ◽  
Shear Yield Stress ◽  
Particle Chain ◽  
Solids Loading ◽  
Mr Fluids ◽  
Shear Yield ◽  
Microstructure Model ◽  
Novel Method ◽  
A Chain

This research details a novel method of increasing the shear yield stress of magnetorheological (MR) fluids by combining shear and squeeze modes of operation to manipulate particle chain structures, to achieve so-called compression-assisted aggregation. The contribution of both active gap separation and particle concentration are experimentally measured using a custom-built Searle cell magnetorheometer, which is a model device emulating a rotary Magnetorheological Energy Absorber (MREA). Characterization data from large (1 mm) and small (250 μm) gap geometries are compared to investigate the effect of the gap on yield stress by compression enhancement. Two MR fluids having different particle concentrations (32 vol% and 40 vol%) are also characterized to demonstrate the effect of solids loading on compression-assisted chain aggregation. Details of the experimental setup and method are presented, and a chain microstructure model is used to explain experimental trends. The torque resisted by practical rotary MREAs is directly related to the strength of the MR fluid used, as measured by the shear yield stress. This study demonstrates that it is feasible, utilizing the compression-enhanced shear yield stress, to either (1) design a rotary MREA of a given volume to achieve higher energy absorption density (energy absorbed normalize by device volume), or (2) reduce the volume of a given rotary MREA to achieve the same energy absorption density.

Compression Enhanced Shear Yield Stress of Electrorheological Fluid

2009 ◽  
Vol 26 (4) ◽  
pp. 048301 ◽  
Author(s):  
Zhang Min-Liang ◽  
Tian Yu ◽  
Jiang Ji-Le ◽  
Zhu Xu-Li ◽  
Meng Yong-Gang ◽  
...  
Keyword(s):  
Yield Stress ◽  
Electrorheological Fluid ◽  
Shear Yield Stress ◽  
Shear Yield
Sign in / Sign up

Export Citation Format

Share Document