Effect of toughened polyamide-coated carbon fiber fabric on the mechanical performance and fracture toughness of CFRP

2021 ◽  
pp. 002199832199945
Author(s):  
Jong H Eun ◽  
Bo K Choi ◽  
Sun M Sung ◽  
Min S Kim ◽  
Joon S Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Photoelectron Spectroscopy ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Internal Damage ◽  
Impact Tests ◽  
Flexural Tests ◽  
The Impact

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed. The mechanical properties of the carbon/epoxy composites, such as transverse flexural tests, longitudinal flexural tests, and impact tests, were investigated. After the impact tests, an ultrasonic C-scan was performed to reveal the internal damage area. The interlaminar fracture toughness of the carbon/epoxy composites was measured using a mode I test. The critical energy release rates were increased by 77% compared to the virgin carbon/epoxy composites. The surface morphology of the fractured surface was observed. The toughening mechanism of the carbon/epoxy composites was suggested based on the confirmed experimental data.

scholarly journals Mechanical Performance of Unstitched and Silk Fiber-Stitched Woven Kenaf Fiber-Reinforced Epoxy Composites

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4801
Author(s):  
Yasir Khaleel Kirmasha ◽  
Mohaiman J. Sharba ◽  
Zulkiflle Leman ◽  
Mohamed Thariq Hameed Sultan
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Mechanical Performance ◽  
Mechanical Test ◽  
Natural Fibers ◽  
Silk Fiber ◽  
Epoxy Composites ◽  
Test Results ◽  
The Impact ◽  
Woven Kenaf

Fiber composites are known to have poor through-thickness mechanical properties due to the absence of a Z-direction binder. This issue is more critical with the use of natural fibers due to their low strength compared to synthetic fibers. Stitching is a through-thickness toughening method that is used to introduce fibers in the Z-direction, which will result in better through-thickness mechanical properties. This research was carried out to determine the mechanical properties of unstitched and silk fiber-stitched woven kenaf-reinforced epoxy composites. The woven kenaf mat was stitched with silk fiber using a commercial sewing machine. The specimens were fabricated using a hand lay-up method. Three specimens were fabricated, one unstitched and two silk-stitched with deferent stitching orientations. The results show that the stitched specimens have comparable in-plane mechanical properties to the unstitched specimens. For the tensile mechanical test, stitched specimens show similar and 17.1% higher tensile strength compared to the unstitched specimens. The flexural mechanical test results show around a 9% decrease in the flexural strength for the stitched specimens. On the other hand, the Izod impact mechanical test results show a significant improvement of 33% for the stitched specimens, which means that stitching has successfully improved the out-of-plane mechanical properties. The outcome of this research indicates that the stitched specimens have better mechanical performance compared to the unstitched specimens and that the decrease in the flexural strength is insignificant in contrast with the remarkable enhancement in the impact strength.

scholarly journals The impact of fibre processing on the mechanical properties of epoxy matrix composites and wood-based particleboard reinforced with hemp (Cannabis sativa L.) fibre

2022 ◽  
Author(s):  
Albert Hernandez-Estrada ◽  
Jörg Müssig ◽  
Mark Hughes
Keyword(s):  
Mechanical Properties ◽  
Fracture Zone ◽  
Structural Integrity ◽  
Bending Strength ◽  
Cannabis Sativa ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Fibre Reinforcement ◽  
Fibre Bundles ◽  
The Impact

AbstractThis work investigated the impact that the processing of hemp (C. sativa L.) fibre has on the mechanical properties of unidirectional fibre-reinforced epoxy resin composites loaded in axial tension, and particleboard reinforced with aligned fibre bundles applied to one surface of the panel. For this purpose, mechanically processed (decorticated) and un-processed hemp fibre bundles, obtained from retted and un-retted hemp stems, were utilised. The results clearly show the impact of fibre reinforcement in both materials. Epoxy composites reinforced with processed hemp exhibited 3.3 times greater tensile strength when compared to the un-reinforced polymer, while for the particleboards, the bending strength obtained in those reinforced with processed hemp was 1.7 times greater than the un-reinforced particleboards. Moreover, whether the fibre bundles were processed or un-processed also affected the mechanical performance, especially in the epoxy composites. For example, the un-processed fibre-reinforced epoxy composites exhibited 49% greater work of fracture than the composites reinforced with processed hemp. In the wood-based particleboards, however, the difference was not significant. Additionally, observations of the fracture zone of the specimens showed different failure characteristics depending on whether the composites were reinforced with processed or un-processed hemp. Both epoxy composites and wood-based particleboards reinforced with un-processed hemp exhibited fibre reinforcement apparently able to retain structural integrity after the composite’s failure. On the other hand, when processed hemp was used as reinforcement, fibre bundles showed a clear cut across the specimen, with the fibre-reinforcement mainly failing at the composite's fracture zone.

scholarly journals Experimental Investigation of the Mechanical Properties and Fire Behavior of Epoxy Composites Reinforced by Fabrics and Powder Fillers

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 738
Author(s):  
Kamila Sałasińska ◽  
Mikelis Kirpluks ◽  
Peteris Cabulis ◽  
Andrejs Kovalovs ◽  
Eduard Skukis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composites ◽  
Fire Behavior ◽  
Epoxy Composites ◽  
Impact Behavior ◽  
Cone Calorimetry ◽  
Burning Behavior ◽  
Different Types ◽  
Flexural Tests ◽  
The Impact

Different types of fabrics, such as aramid (A), carbon (C), basalt (B), glass (G), and flax (F), as well as powder fillers, were used to manufacture the epoxy-based hybrid composites by the hand-lay-up method. In this work, a few research methods, including hardness, flexural tests, puncture impact behavior, as well as cone calorimetry (CC) measurements, were applied to determine the impact of type fillers and order of fabrics on the performance and burning behavior of hybrid composites. The mechanical properties were evaluated to correlate with the microstructure and consider together with thermogravimetric analysis (TGA) data.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Effect of Filler Compositions on the Mechanical Properties of Bamboo Filled Polyester Composite

2014 ◽  
Vol 879 ◽  
pp. 90-95 ◽  
Author(s):  
Abdul Rahman Noor Leha ◽  
Nor Amalina Nordin
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Impact Test ◽  
Compression Molding ◽  
Engineering Applications ◽  
Maximum Value ◽  
Polyester Composite ◽  
Bamboo Powder ◽  
Flexural Tests ◽  
The Impact

Biocomposite from bamboo powder was fabricated by compression molding technique. The objective of this study was to investigate the mechanical properties of bamboo compounded with epoxy with different ratio. Tensile and flexural tests were done to characterize its mechanical properties. It was observed that the strength of bamboo-polyester was increased with increasing amount of bamboo powder. The tensile and flexural strength shows the highest value at 25 wt.% bamboo. However, the impact test shows the maximum value at 20 wt.% bamboo powder. These results exhibit the bamboo-polyester can be a good candidate to be used in many engineering applications

scholarly journals Influence of layering pattern of modified kenaf fiber on thermomechanical properties of epoxy composites

2019 ◽  
Vol 36 (1) ◽  
pp. 47-62
Author(s):  
AR Mohammed ◽  
MS Nurul Atiqah ◽  
Deepu A Gopakumar ◽  
MR Fazita ◽  
Samsul Rizal ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Chemical Modification ◽  
Epoxy Matrix ◽  
Epoxy Composites ◽  
Woven Composites ◽  
Fiber Reinforced ◽  
Kenaf Fiber ◽  
Kenaf Fibers ◽  
The Impact ◽  
Woven Kenaf

Natural fiber-reinforced composites gained considerable interest in the scientific community due to their eco-friendly nature, cost-effective, and excellent mechanical properties. Here, we reported a chemical modification of kenaf fiber using propionic anhydride to enhance the compatibility with the epoxy matrix. The incorporation of the modified woven and nonwoven kenaf fibers into the epoxy matrix resulted in the improvement of the thermal and mechanical properties of the composite. The thermal stability of the epoxy composites was enhanced from 403°C to 677°C by incorporating modified woven kenaf fibers into the epoxy matrix. The modified and unmodified woven kenaf fiber-reinforced epoxy composites had a tensile strength of 64.11 and 58.82 MPa, respectively. The modified woven composites had highest flexural strength, which was 89.4 MPa, whereas, for unmodified composites, it was 86.8 MPa. The modified woven fiber-reinforced epoxy composites showed the highest value of flexural modulus, which was 6.0 GPa compared to unmodified woven composites (5.51 GPa). The impact strength of the epoxy composites was enhanced to 9.43 kJ m−2 by the incarnation of modified woven kenaf fibers into epoxy matrix. This study will be an effective platform to design the chemical modification strategy on natural fibers for enhancing the compatibility toward the hydrophobic polymer matrices.

scholarly journals Characteristics and mechanical properties changes due to incorporation of aloe vera in polyethylene-based film

2020 ◽  
Vol 17 (2) ◽  
pp. 61
Author(s):  
Siti Fatma Abd Karim ◽  
Junaidah Binti Jai ◽  
Ku Halim Ku Hamid ◽  
Abdul Wafi Abdul Jalil
Keyword(s):  
Mechanical Properties ◽  
Thermal Degradation ◽  
Aloe Vera ◽  
Functional Materials ◽  
Chain Structure ◽  
Substantial Effect ◽  
Scanning Calorimetry ◽  
Degradation Temperature ◽  
And Performance ◽  
The Impact

Non-degradable properties of polyethylene (PE) films due to long-chain structure cause increment of solid waste plastic. Many researchers, with different purposes, have studied the incorporation of functional materials to PE. Studying the impact of incorporation of aloe vera (AV) into PE films in terms of its characteristic and mechanical properties is the main objective of this paper. The films were prepared using melt-blending and hot press technique. The characterization assessed for the PE and PE-AV films were spectroscopy, crystalline phase, thermal analysis and performance of mechanical properties of the sample.  The functional group detected in spectroscopy studied did not show any changes for PE film or PE with the presence of AV. Lower thermal degradation temperature (Td) obtained for PE-AV3 while others film found no significant changes of Td value and only one peak of thermal degradation occurred for all film. The same goes to the analysis obtained from differential scanning calorimetry (DSC) data. However, the crystalline structure displayed momentous peak changes for PE with AV. The highest tensile strength (TS) obtained by PE-AV3, at once developing highest value of Young’s modulus (YM), modulus of resilience (UE) and modulus of toughness (UT). A certain amount of AV has substantial effect on changing the polymeric structure especially improving the mechanical properties of PE film. Therefore, AV has potential to become an additive for developing a new partially degradable PE film.

Preparation and Mechanical Properties of Epoxy Resin Reinforced with Jeffamines-Grafted Carbon Nanotubes

2009 ◽  
Vol 79-82 ◽  
pp. 553-556 ◽  
Author(s):  
Ling Fei Shi ◽  
Gang Li ◽  
Gang Sui ◽  
Xiao Ping Yang
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Photoelectron Spectroscopy ◽  
Epoxy Matrix ◽  
Resin Matrix ◽  
Mechanical And Thermal Properties ◽  
Time Dynamic ◽  
Multi Walled Carbon Nanotubes ◽  
The Impact

The increasing proliferation and application of advanced polymer composites requires higher and broader performance resin matrices. Poly(oxypropylene) with –NH2 end-groups has been widely used to toughen epoxy resins, but the strength of resin matrix may be reduced due to the addition of flexible segments in the crosslinking network. Carbon nanotubes (CNTs) have been paid more and more attention in recent years because of their superior thermal and mechanical properties. In this paper, CNTs grafted with Jeffamines T403 were used to simultaneously improve the reinforcement and toughening of an epoxy resin. The untreated multi-walled carbon nanotubes (u-MWNTs) were functionalized with amine groups according to three steps: carboxylation, acylation, and amidation. The f-MWNTs were characterized by Fourier transform infra-red (FTIR) and X-ray photoelectron spectroscopy (XPS). The experimental results indicated that the T403 was grafted to the surface of MWCNTs. The mechanical and thermal properties of epoxy with f-MWNTs were investigated. The tensile and flexural strength increased by 7.77 % and 7.03 % after adding 0.5wt% f-MWCNTs without sacrificing the impact toughness. At the same time, dynamic mechanical thermal analysis (DMTA) showed that the glass transition temperature (Tg) of epoxy with f-MWNTs were increased. The fracture surface of epoxy with f-MWNTs was observed by scanning electron microscopy (SEM) to understand the dispersion of f-MWNTs in epoxy matrix and interfacial adhesion between f-MWNTs and epoxy matrix, which can be attributed to the strong interfacial bonding between f-MWNTs and epoxy resin.

scholarly journals Improving the mechanical properties of commercial feldspathic dental porcelain by addition of Alumina-Zirconia

2019 ◽  
pp. 67-76
Author(s):  
Juliana Gómez ◽  
Astrid Rueda ◽  
Edgar Alexader Ossa Henao
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Contact Resistance ◽  
Mechanical Performance ◽  
Tetragonal Zirconia ◽  
Dental Ceramics ◽  
Aesthetic Response ◽  
Early Failure ◽  
Feldspathic Porcelain ◽  
Natural Tooth

Dental ceramics made from Yttria stabilized tetragonal Zirconia polycrystalline (Y-TZP) with feldspathic porcelain veneers have similar mechanical and aesthetic response to natural tooth. However, cases of early failure, such as chipping or fracture in the veneering have been reported after short periods of use. The present study evaluated the feldspathic porcelain (VITA-VM9) with addition of 0.5 and 2.5 wt% Alumina-Zirconia as reinforcing agents. Hardness, fracture toughness, contact resistance and color variations were evaluated finding better mechanical performance on the new formulations.

scholarly journals The Effects of Silica-Based Fillers on the Properties of Epoxy Molding Compounds

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1811 ◽  
Author(s):  
Mitja Linec ◽  
Branka Mušič
Keyword(s):  
Mechanical Properties ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Fused Silica ◽  
Spiral Flow ◽  
Scanning Calorimetry ◽  
Molding Compounds ◽  
Material Development ◽  
The Impact

Global design and manufacturing of the materials with superb properties remain one of the greatest challenges on the market. The future progress is orientated towards researches into the material development for the production of composites of better mechanical properties to the existing materials. In the field of advanced composites, epoxy molding compounds (EMCs) have attained dominance among the common materials due to their excellent properties that can be altered by adding different fillers. One of the main fillers is often based on silicon dioxide (SiO2). The concept of this study was to evaluate the effects of the selected silica-based fillers on the thermal, rheological, and mechanical properties of EMCs. Various types of fillers with SiO2, including crystalline silica and fused silica, were experimentally studied to clarify the impact of filler on final product. Fillers with different shape (scanning electron microscope, SEM), along with different specific surface area (specific surface area analyzer, BET method) and different chemical structure, were tested to explore their modifications on the EMCs. The influence of the fillers on the compound materials was determined with the spiral flow length (spiral flow test, EMMI), glass transition temperature (differential scanning calorimetry, DSC), and the viscosity (Torque Rheometer) of the composites.

Sign in / Sign up

Export Citation Format

Share Document