scholarly journals Particle Size Effect of Oyster Shell on Mortar: Experimental Investigation and Modeling

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6813
Author(s):  
Yingdi Liao ◽  
Hongyi Shi ◽  
Shimin Zhang ◽  
Bo Da ◽  
Da Chen
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Particle Sizes ◽  
River Sand ◽  
Standard Requirement ◽  
Slump Flow ◽  
Curing Age

In order to solve the problem of lack of natural river sand, crushed waste oyster shells (WOS) were used to replace river sand. By replacing 20% river sand, WOS mortar with different particle sizes of WOS were made for the experiment. Through experimental observation, the initial slump and slump flow loss rate were studied. The effects of different particle sizes and curing times on the compressive strength, flexural strength, static elastic modulus, and dry shrinkage of WOS mortar were analyzed. The relationship formulas between the compressive strength, flexural strength, particle size, and curing age were proposed. The results showed that the setting time and slump flow decreased with a decrease in the particle size of WOS. It was also found that the mortar with fine crushed WOS had high compressive strength, flexural strength, and static elastic modulus at both early and long-term curing age. A formula was proposed to describe the development of the compressive strength with the particle size of WOS and curing time, and the relations among these mechanical properties were discussed. Furthermore, drying shrinkage increased when WOS was used and could not satisfy the standard requirement of 0.075%. In contrast, the addition of fine WOS and double-dose sulfonated naphthalene-formaldehyde superplasticizer (SNF SP) reduced the shrinkage rate of the mortar by 8.35% and provided better workability and mechanical properties for mortar.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Evaluation of Strengths from Cement Hydration and Slag Reaction of Mortars Containing High Volume of Ground River Sand and GGBF Slag

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Punnaman Norrarat ◽  
Weerachart Tangchirapat ◽  
Smith Songpiriyakij ◽  
Chai Jaturapitakkul
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Cement Hydration ◽  
High Volume ◽  
Inert Material ◽  
Early Age ◽  
Particle Sizes ◽  
River Sand ◽  
Reactive Material ◽  
Median Particle

This paper investigates the cement hydration, and the slag reaction contributes to the compressive strengths of mortars mixed with ground river sand (GRS) and ground-granulated blast furnace (GGBF) slag with different particle sizes. GRS (inert material) and GGBF slag (reactive material) were ground separately until the median particle sizes of 32 ± 1, 18 ± 1, and 5 ± 1 micron and used to replace Portland cement (PC) in large amount (40–60%) by weight of the binder. The results showed that, at the early age, the compressive strength obtained from the cement hydration was higher than that obtained from the slag reaction. The results of compressive strength also indicated that the GGBF slag content and particle size play important roles in the slag reaction at the later ages, whereas cement hydration is more prominent at the early ages. Although the results could be expected from the use of GGBF slag to replace PC in mortar or concrete, this study had presented the values of the compressive strength along with ages and the finenesses of GGBF slag that contributed from cement hydration and from GGBF slag reaction.

Evaluation of Relations among Basic Mechanical Properties of Concrete with Machine-Made Sand

2011 ◽  
Vol 418-420 ◽  
pp. 441-444 ◽  
Author(s):  
Feng Lan Li ◽  
Yan Zeng ◽  
Chang Yong Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Rough Surface ◽  
Design Code ◽  
Ordinary Concrete ◽  
Axial Compressive Strength ◽  
Different Characteristics

Due to many different characteristics such as irregular polygon particle with pointed edges, rough surface and larger content of stone powder, machine-made sand has ignorable effects on the properties of concrete. As the basis for the design of concrete structures, the relations among the basic mechanical properties of concrete such as compressive strength, tensile strength, flexural strength and elastic modulus should be clearly understood. This paper summarizes the test data from the published references, and discusses the relations among these properties by statistical analyses compared with those of ordinary concrete. The results show that the axial compressive strength and the tensile strength can be prospected by the same formulas of ordinary concrete specified in current Chinese design code, but the prospected tensile strength should multiply a reducing coefficient when the strength grade of concrete is lower than C30. The elastic modulus of concrete with machine-made sand is larger than that of ordinary concrete, which should be prospect by the formula in this paper. Meanwhile, the formula of flexural strength is suggested.

The Influence of Aggregates on the Properties of Concrete

2014 ◽  
Vol 1000 ◽  
pp. 277-280 ◽  
Author(s):  
Pavel Šiler ◽  
Ondřej Bezděk ◽  
Iva Kolářová ◽  
Eva Bartoníčková ◽  
Tomáš Opravil ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Particle Size Analysis ◽  
Hydration Process ◽  
Silica Sand ◽  
Size Analysis ◽  
Isoperibolic Calorimetry

This work is focused on the influence of aggregates on the mechanical properties of concrete and hydration process. The flexural strength and compressive strength were observed after 1, 7 and 28 days of curing. The process of hydration was monitored using isoperibolic calorimetry. Laser particle size analysis of aggregates was also performed. The following materials were used: Portland cement CEM I 42,5 R-Sc, finely ground silica sand, calcinated bauxite, fine, medium and rough testing sand (defined in ČSN EN 196-1).

Influence of Variable Temperature Curing on Mechanical Properties of Fly Ash Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 178-181
Author(s):  
Ya Ding Zhao ◽  
Xue Ying Li ◽  
Ling Chao Kong ◽  
Wei Du
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Variable Temperature ◽  
Improve Performance ◽  
Curing Conditions ◽  
Fly Ash Concrete ◽  
Better Than

Under variable temperature curing conditions(30 oC ~70 oC), concrete with fly ash whose compressive strength, flexural strength, and dynamic elastic modulus are better than ones without fly ash.Compared with constant temperature 20oC, 50 oC and 70 oC, variable temperature curing(VTC) is benefit for the improvement of mechanical properties of 30% fly ash concrete, but which is no advantage to improve performance of 50% fly ash concrete.

scholarly journals Study on Mechanical Properties of PET Fiber-Reinforced Coal Gangue Fine Aggregate Concrete

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Yanlin Huang ◽  
An Zhou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Plain Concrete ◽  
Coal Gangue ◽  
Fine Aggregate ◽  
Replacement Rate ◽  
River Sand ◽  
Aggregate Concrete

In recent years, with the rapid development of the construction industry, the demand for natural river sand has become increasingly prominent. Development of alternatives to river sand has become an interesting direction for concrete research. In this paper, coal gangue was proposed to replace part of the river sand to produce coal gangue fine aggregate concrete, while waste polyethene terephthalate (PET) bottles were used as raw materials to make PET fibers to improve the mechanical properties of coal gangue fine aggregate concrete. There were two parts of the test conducted. In the first part, the compressive strength of the gangue fine aggregate concrete cube, splitting tensile strength, axial compressive strength, and static elastic modulus were studied when the substitution rate of coal gangue increased from 0% to 50%. Referring to the equation of the full stress-strain curve of plain concrete, the stress-strain constitutive equation of coal gangue fine aggregate concrete was analyzed and studied. By comparing with plain concrete, it was found that the coal gangue concrete with a replacement rate of 50% had higher compressive strength and tensile strength, but its brittleness was significantly greater than that of plain concrete in the later stage. In the second part, by studying the effect of different PET fiber content on the mechanical properties of coal gangue fine aggregate concrete with a replacement rate of 50%, it was found that when the addition of PET fiber was 0.1% and 0.3%, not only were compressive strength, splitting tensile strength, static elastic modulus, and flexural strength of the gangue fine aggregate concrete effectively improved but also the brittleness of concrete can be significantly reduced. The study found that after adding 0.3% PET fiber, the coal gangue fine aggregate concrete with a replacement rate of 50% has better mechanical properties and less brittleness.

scholarly journals Fresh, Mechanical Properties and Impact Resistance Behavior of Eco-Friend Self-Compacted Concrete

2019 ◽  
Vol 22 (3) ◽  
pp. 208-212
Author(s):  
Sheelan M. Hama ◽  
Alhareth M. Abdulghafor ◽  
Mohammed Tarrad Nawar
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Glass Powder ◽  
Impact Resistance ◽  
Waste Glass ◽  
Slump Flow ◽  
Waste Glass Powder ◽  
Self Compact Concrete

In this work, waste glass powder from broken windows and plastic fibers from waste polyethylene terephthalate bottles are utilized to produce an economical self-compact concrete. Fresh properties (slump flow diameter, slump Flow T50, V. Funnel, L–Box), mechanical properties (Compressive strength and Flexural strength) and impact resistance of self-compact concrete are investigated. 15% waste glass powder as a partial replacement of cement with five percentages of polyethylene terephthalate plastic waste were adopted: 0% (reference), 0.5%, 0.75%, 1%, 1.25% and 1.5% by volume. It seems that the flow ability of self-compact concrete decreases with the increasing of the amount of plastic fibers. The compressive strength was increased slightly with plastic fiber content up to (0.75%), about 4.6% For more than (0.75%) plastic fiber. The compressive strength began to decrease about 15.2%. The results showed an improvement in flexural strength and an impact on the resistance in all tested specimens’ content of the plastic fibers, especially at (1.5%) fibers.

Effect of Low Temperature on Mechanical Properties of Concrete with Different Strength Grade

2011 ◽  
Vol 477 ◽  
pp. 308-312 ◽  
Author(s):  
Xiao Ping Cai ◽  
Wen Cui Yang ◽  
Jie Yuan ◽  
Yong Ge ◽  
Bao Sheng Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Low Temperature ◽  
Flexural Strength ◽  
Splitting Tensile Strength ◽  
Growth Ratio ◽  
Strength Grade

The effect of low temperature (-35°C) on the mechanical properties of concrete with different strength grade such as compressive strength, flexural strength, splitting tensile strength and elastic modulus was studied. The results showed that all of the mechanical properties were improved at -35°C. It was also can be found from the tests, as the strength grade increased, the growth ratios at -35°C of compressive strength, flexural strength and splitting tensile strength decreased. But the growth ratio of elastic modulus increased with the increasing of strength grade.

Basic Mechanics Characters of Recycled Fine Aggregate Concrete

2012 ◽  
Vol 446-449 ◽  
pp. 2028-2032 ◽  
Author(s):  
Jian Geng ◽  
Yong Yong Chen ◽  
Jia Ying Sun ◽  
Wei Chen
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fine Aggregate ◽  
Aggregate Concrete ◽  
Recycled Fine Aggregate ◽  
Minimum Particle Size ◽  
Axial Compressive Strength ◽  
Mechanical Characters

In this article, the basic mechanical characters of recycled fine aggregate concrete (RFAC) are studied, and the relationships of recycled fine aggregate (RFA) content, minimum particle size and water content with them are also discussed according to results of cubic compressive strength （f¬¬cu）, flexural strength （ff）, splitting tensile strength（fts）, axial compressive strength（fc）and Yang’s modulus （Ec）. The results indicate that the use of RFA will induce mechanical properties of RFAC to deteriorate, and the deteriorated trend of it become more obviously with RFA content increased and minimum particle size reduced, in addition to, the early compressive strength of RFA develop slowly. The RFAC elastic modulus is significantly lower than ordinary concrete, besides, RFA on elastic modulus was significantly affected than other mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document