scholarly journals Indentation Size Effect in CoCrFeMnNi HEA Prepared by Various Techniques

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7246
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Jiří Čapek ◽  
Filip Průša
Keyword(s):  
Size Effect ◽  
Melt Spinning ◽  
Indentation Size Effect ◽  
Indentation Size ◽  
High Entropy ◽  
Additional Information ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Application Potential ◽  
Penetration Depths

High entropy alloys (HEAs) are materials of great application potential and which have been extensively studied during the last two decades. As the number of possible element combinations is enormous, model materials representing certain groups of HEAs are used for the description of microstructure, properties, and deformation mechanisms. In this study, the microstructure and mechanical properties of the so-called Cantor alloy composed of Co, Cr, Fe, Mn, and Ni in equiatomic ratios prepared by various techniques (casting, melt-spinning, spark plasma sintering) were examined. The research focused on the indentation measurements, namely, the indentation size effect describing the evolution of the hardness with penetration depth. It was found that the standard Nix–Gao model can be used for this type of alloy at higher penetration depths and its parameters correlate well with microstructural observations. The Nix–Gao model deviates from the measured data at the submicrometer range and the applied modification affords additional information on the deformation mechanism.

scholarly journals Structure and Deformation Behavior of Ti-SiC Composites Made by Mechanical Alloying and Spark Plasma Sintering

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1276 ◽  
Author(s):  
Dariusz Garbiec ◽  
Volf Leshchynsky ◽  
Alberto Colella ◽  
Paolo Matteazzi ◽  
Piotr Siwak
Keyword(s):  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Indentation Size Effect ◽  
Sintering Temperature ◽  
High Energy ◽  
Indentation Size ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball

Combining high energy ball milling and spark plasma sintering is one of the most promising technologies in materials science. The mechanical alloying process enables the production of nanostructured composite powders that can be successfully spark plasma sintered in a very short time, while preserving the nanostructure and enhancing the mechanical properties of the composite. Composites with MAX phases are among the most promising materials. In this study, Ti/SiC composite powder was produced by high energy ball milling and then consolidated by spark plasma sintering. During both processes, Ti3SiC2, TiC and Ti5Si3 phases were formed. Scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction study showed that the phase composition of the spark plasma sintered composites consists mainly of Ti3SiC2 and a mixture of TiC and Ti5Si3 phases which have a different indentation size effect. The influence of the sintering temperature on the Ti-SiC composite structure and properties is defined. The effect of the Ti3SiC2 MAX phase grain growth was found at a sintering temperature of 1400–1450 °C. The indentation size effect at the nanoscale for Ti3SiC2, TiC+Ti5Si3 and SiC-Ti phases is analyzed on the basis of the strain gradient plasticity theory and the equation constants were defined.

scholarly journals INDENTATION SIZE EFFECT IN HIGH PRESSURE TORSION PROCESSED HIGH ENTROPY ALLOY

2020 ◽  
Vol 27 ◽  
pp. 141-144
Author(s):  
Petr Haušild ◽  
Jakub Čížek ◽  
Jaroslav Čech ◽  
Jiří Zýka ◽  
Hyoung Seop Kim
Keyword(s):  
High Pressure ◽  
Size Effect ◽  
Indentation Size Effect ◽  
High Pressure Torsion ◽  
High Entropy Alloy ◽  
Indentation Size ◽  
Depth Of Penetration ◽  
Slow Cooling ◽  
Cast Sample ◽  
High Entropy

High entropy alloy HfNbTaTiZr in as cast conditions and after high pressure torsion straining was characterized by nanoindentation. The length-scale dependent material response (indentation size effect) was characterized by indentation at various indentation depths. Hardness dependence on the characteristic length (depth of penetration) indicated decomposition of disordered high entropy alloy in the as cast sample, which probably occurred during slow cooling after casting. Subsequent severe plastic deformation by high pressure torsion led on the other hand to the short-range disorder of (originally partially decomposed as cast) structure. Further hardening was generated during high pressure torsion by the mechanisms of grain refinement and increasing dislocation density.

scholarly journals The indentation size effect of single-crystalline tungsten revisited

2021 ◽  
Author(s):  
Jin Wang ◽  
Tillmann Volz ◽  
Sabine M. Weygand ◽  
Ruth Schwaiger
Keyword(s):  
Size Effect ◽  
Strain Rate ◽  
Indentation Size Effect ◽  
Defect Density ◽  
Slip Systems ◽  
Indentation Size ◽  
Pronounced Increase ◽  
Single Crystalline ◽  
Geometrically Necessary Dislocation ◽  
Penetration Depths

AbstractIn this study, we have investigated the indentation size effect (ISE) of single crystalline tungsten with low defect density. As expected, the hardness shows a pronounced increase with decreasing indentation depth as well as a strong strain rate dependence. For penetration depths greater than about 300 nm, the ISE is well captured by the Nix–Gao model in the context of geometrically necessary dislocations. However, clear deviations from the model are observed in the low depth regime resulting in a bilinear effect. The hardness behavior in the low depth regime can be modeled assuming a non-uniform spacing of the geometrically necessary dislocations. We propose that the bilinear indentation size effect observed reflects the evolution of the geometrically necessary dislocation density. With increasing strain rate, the bilinear effect becomes less pronounced. This observation can be rationalized by the activation of different slip systems. Graphic abstract

Indentation size effect and wear characteristics of spark plasma sintered, hard MWCNT/Al2O3nanocomposites

2015 ◽  
Vol 114 (8) ◽  
pp. 448-455 ◽  
Author(s):  
P. Sikder ◽  
A. Pramanick ◽  
S. Sarkar ◽  
S. Das ◽  
P. P. Dey ◽  
...  
Keyword(s):  
Size Effect ◽  
Indentation Size Effect ◽  
Indentation Size ◽  
Wear Characteristics ◽  
Spark Plasma

scholarly journals Fabrication and Characterization of Quinary High Entropy-Ultra-High Temperature Diborides

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 108-120
Author(s):  
Simone Barbarossa ◽  
Roberto Orrù ◽  
Valeria Cannillo ◽  
Antonio Iacomini ◽  
Sebastiano Garroni ◽  
...  
Keyword(s):  
High Temperature ◽  
Single Phase ◽  
Nominal Composition ◽  
High Entropy ◽  
Chemical Complexity ◽  
Alternative Processing ◽  
Plasma Sintering ◽  
High Temperature Synthesis ◽  
Spark Plasma

Due to their inherent chemical complexity and their refractory nature, the obtainment of highly dense and single-phase high entropy (HE) diborides represents a very hard target to achieve. In this framework, homogeneous (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2, (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2, and (Hf0.2Zr0.2Nb0.2Mo0.2Ti0.2)B2 ceramics with high relative densities (97.4, 96.5, and 98.2%, respectively) were successfully produced by spark plasma sintering (SPS) using powders prepared by self-propagating high-temperature synthesis (SHS). Although the latter technique did not lead to the complete conversion of initial precursors into the prescribed HE phases, such a goal was fully reached after SPS (1950 °C/20 min/20 MPa). The three HE products showed similar and, in some cases, even better mechanical properties compared to ceramics with the same nominal composition attained using alternative processing methods. Superior Vickers hardness and elastic modulus values were found for the (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2 and the (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2 systems, i.e., 28.1 GPa/538.5 GPa and 28.08 GPa/498.1 GPa, respectively, in spite of the correspondingly higher residual porosities (1.2 and 2.2 vol.%, respectively). In contrast, the third ceramic, not containing tantalum, displayed lower values of these two properties (25.1 GPa/404.5 GPa). However, the corresponding fracture toughness (8.84 MPa m1/2) was relatively higher. This fact can be likely ascribed to the smaller residual porosity (0.3 vol.%) of the sintered material.

scholarly journals Understanding the Links between the Composition-Processing-Properties in New Formulations of HEAs Sintered by SPS

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 888
Author(s):  
Paula Alvaredo-Olmos ◽  
Jon Molina-Aldareguía ◽  
Alvaro Vaz-Romero ◽  
Estela Prieto ◽  
Jesús González-Julián ◽  
...  
Keyword(s):  
High Hardness ◽  
Processing Parameters ◽  
Heating Rates ◽  
High Entropy ◽  
Plasma Sintering ◽  
Mechanical Study ◽  
Spark Plasma ◽  
Processing Properties ◽  
Bcc Phase ◽  
Hardness Values

This work presents two new compositions of high entropy alloys (HEAs) that were designed with the aim of obtaining a body-centered cubic (BCC) phase with high hardness values and a moderate density. Sintering was performed using Spark Plasma Sintering (SPS) with different heating rates to determine the influence of the processing parameters on the phase formation. The microstructural study revealed that the presence of Ni in the composition promoted phase separation, and the mechanical study confirmed a clear influence on the mechanical properties of both the composition and heating rate. The combination of microscopy with compression and nanoindentation tests at room and high temperature made it possible to advance our understanding of the relationships between the composition, processing, and properties of this emerging group of alloys.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

Sign in / Sign up

Export Citation Format

Share Document