scholarly journals TiO2 Polyamide Thin Film Nanocomposite Reverses Osmosis Membrane for Water Desalination

Membranes ◽  
2018 ◽  
Vol 8 (3) ◽  
pp. 66 ◽  
Author(s):  
Ahmed Al Mayyahi
Keyword(s):  
Thin Film ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Water Desalination ◽  
Fouling Resistance ◽  
Force Microscopy ◽  
Membrane Performance ◽  
Angle Measurements ◽  
Membrane Characterization ◽  
Trimesoyl Chloride

In this study, TiO2 nanoparticles were inserted into the polyamide layer of traditional thin film composite membrane. The nanoparticles were dispersed in a trimesoyl chloride-hexane solution before interfacial polymerization with m-phenylenediamine-aqueous solution. Membrane characterization was performed via contact angle measurements, atomic force microscopy (AFM), scanning electron microscopy (SEM), and water flux, salt rejection, and fouling resistance evaluation. The results indicate that TiO2 could effectively improve membrane performance. Water flux increased from 40 to 65 L/m² h by increasing NPs concentration from 0 to 0.1 wt. %, while NaCl rejection was above 96%. Moreover, the modified membrane demonstrated better organic fouling resistance and robust antibacterial efficiency.

scholarly journals Effect of Kenaf MCC composition on Thin Film Composite membrane for NaCI Rejection

2019 ◽  
Vol 258 ◽  
pp. 04003
Author(s):  
Azman Ismail ◽  
Ramlah Mohd Tajuddin ◽  
Hamizah Mohktar ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Thin Film ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Sem Images ◽  
Water Contact ◽  
Membrane Performance ◽  
Pure Water Flux

A modified thin film PSf-MCC reverse osmosis membrane was prepared by interfacial polymerization between aqueous MPD and TMC as the organic monomer. Aim of this study is to determine the effect of MCC in membrane formulation and fabrication. The surface and cross section morphology of TFC PSF/MCC membrane shows MCC particle which able to improve hydrophilicity of the membrane. The SEM images showed dense and porous structure of the MCC incorporated membranes. In addition, the water contact angle measurement also confirmed the increased hydrophilicity of the modified membranes. The effect of MCC on membrane matric influence the membrane performance in terms of NaCl rejection and pure water flux. Results showed that TFC PSf/MCC membrane shows NaCl rejection up to 98.9% compared with TFC PSf membrane. TFC PSf/MCC membrane also showed the highest pure water flux which is 3.712 Lm2/hr compare with TFC PSF membrane which is 3.606 Lm2/hr. The overall result proved that MCC particle could improve membrane hydrophilicity hence, increased pure water flux and salt rejection.

IMPACTS OF HYDROPHILIC NANOFILLERS ON SEPARATION PERFORMANCE OF THIN FILM NANOCOMPOSITE REVERSE OSMOSIS MEMBRANE

2016 ◽  
Vol 78 (12) ◽  
Author(s):  
C. Y. Chong ◽  
G. S. Lai ◽  
W. J. Lau ◽  
N. Yusof ◽  
P. S. Goh ◽  
...  
Keyword(s):  
Thin Film ◽  
Water Permeability ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Water Desalination ◽  
Separation Performance ◽  
Salt Rejection ◽  
Tfc Membrane ◽  
Thin Film Nanocomposite

The membrane technology is still considered a costly method to produce potable water. In view of this, RO membrane with enhanced water permeability without trade-off in salt rejection is desirable as it could further reduce the cost for water desalination. In this study, thin film nanocomposite (TFN) membranes containing 0.05 or 0.10 w/v% hydrophilic nanofillers in polyamide layer were synthesized via interfacial polymerization of piperazine and trimesoyl chloride monomers. The resultant TFN membranes were characterized and compared with a control thin film composite (TFC) membrane. Results from the filtration experiments showed that TFN membranes exhibited higher water permeability, salt rejection and fouling resistance compared to that of the TFC membrane. Excessive amount of nanofillers incorporated in the membrane PA layer however negatively affected the cross-linking in the polymer matrix, thus deteriorating the membrane salt rejection. TFN membrane containing 0.05 w/v% of nanofillers showed better performances than the TFC membrane, recording a pure water flux of 11.2 L/m2∙h, and salt rejection of 95.4%, 97.3% and 97.5% against NaCl, Na2SO4 and MgSO4, respectively. 

Physicochemical characteristics of poly(piperazine-amide) TFC nanofiltration membrane prepared at various reaction times and its relation to the performance

2015 ◽  
Vol 35 (1) ◽  
pp. 71-78 ◽  
Author(s):  
Nurasyikin Misdan ◽  
Woei Jye Lau ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Water Permeability ◽  
Interfacial Polymerization ◽  
Reaction Times ◽  
Physicochemical Characteristics ◽  
Attenuated Total Reflection ◽  
Operating Pressure ◽  
Polymerization Time ◽  
Force Microscopy ◽  
Membrane Performance ◽  
Trimesoyl Chloride

Abstract Poly(piperazine-amide) thin film composite (TFC) nanofiltration (NF) membranes were prepared via interfacial polymerization (IP) of trimesoyl chloride (TMC) in cyclohexane and piperazine (PIP) in water. The effect of polymerization time on the physicochemical characteristics of poly(piperazine-amide) layers and the final membrane performance was studied in detail. The morphological structures of prepared membranes were investigated using atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), by contrast, was used to determine the chemical characteristics of the membranes. It is evident that the surface roughness increased with increasing polymerization time due to the formation of a supergranule-like structure over the interfacially synthesized poly(piperazine-amide) layer. Moreover, increasing the polymerization time led to a dramatic reduction of water permeability due to the significant increase of crosslinking poly(piperazine-amide) barrier layers. Experimentally determined data showed that the TFC NF membrane prepared at 10 s of polymerization time experienced 51.2 l/m2.h of water permeability with 97.02% of Na2 SO4 salt rejection at an operating pressure of 0.6 MPa.

scholarly journals Role of Cellulose Micro and Nano Crystals in Thin Film and Support Layer of Nanocomposite Membranes for Brackish Water Desalination

Membranes ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 101 ◽  
Author(s):  
Mohammed Kadhom ◽  
Noor Albayati ◽  
Suhaib Salih ◽  
Mustafa Al-Furaiji ◽  
Mohamed Bayati ◽  
...  
Keyword(s):  
Thin Film ◽  
Saline Water ◽  
Water Flux ◽  
Water Desalination ◽  
Nanocomposite Membranes ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Major Process ◽  
Desalination Plants

Reverse osmosis is a major process that produces soft water from saline water, and its output represents the majority of the overall desalination plants production. Developing efficient membranes for this process is the aim of many research groups and companies. In this work, we studied the effect of adding cellulose micro crystals (CMCs) and cellulose nano crystals (CNCs) to the support layer and thin film nanocomposite (TFN) membrane on the desalination performance. SEM, TEM, ATR-FTIR, and contact angle measurements were used to characterize the membrane’s properties; and membrane’s performance were evaluated by water flux and NaCl rejection. Filling 2% of CNCs gel in the support layer improved the water flux by +40%, while salt rejection maintained almost the same, around 95%. However, no remarkable improvement was gained by adding CNCs gel to m-phenylenediamine (MPD) solution, which was used in TFN membrane preparation. Filling CMCs powder in TFN membrane led to a slight improvement in terms of water flux.

scholarly journals Organically Modified Nanoclay Filled Thin-Film Nanocomposite Membranes for Reverse Osmosis Application

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3803 ◽  
Author(s):  
Syed Zaidi ◽  
Farid Fadhillah ◽  
Haleema Saleem ◽  
Alaa Hawari ◽  
Abdelbaki Benamor
Keyword(s):  
Thin Film ◽  
Reverse Osmosis ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Membrane Properties ◽  
X Ray Diffraction ◽  
Membrane Performance ◽  
Transmission Electron ◽  
First Time ◽  
Hexane Solution

This study validates, for the first time, the effectiveness of two nanoclays, that is, cloisite (CS)-15A and montmorillonite (MNT) at the polyamide (PA) active layer in the reverse osmosis (RO) membrane. Cloisite-15A is natural montmorillonite modified with dimethyl dihydrogenated tallow quaternary ammonium salt. Thin-film composite (TFC) membranes were fabricated by the interfacial polymerization (IP) process between the trimesoylchloride (TMC)–n-hexane solution and m-phenylenediamine (MPD)–aqueous solution; the IP process took place on a polysulfone support sheet. The two types of nanoparticles were added in various weight ratios (0.005 wt.%–0.04 wt.%) in the n-hexane solution of TMC. Different characterizations like X-ray diffraction (XRD), contact angle, transmission electron microscopy (TEM), and membrane performance tests were performed to analyse the membrane properties. Both XRD and TEM studies proved that the two nanoclays are successfully anchored at the different sites of the PA layer. CS-15A could accelerate the water flux from 15 to 18.65 L/m2·h with NaCl rejection enhancement from 72% to 80%, relative to the control membrane. Conversely, MNT also enhanced the flux from 15 to 40 L/m2·h, but NaCl rejection reduced from 70% to 23%. The mechanism of water uptake in nanoclays was also discussed. The results pave the way for a complete future study, in which these phenomena should be studied in great detail.

scholarly journals Removal of multiple pesticide residues from water by low-pressure thin-film composite membrane

2020 ◽  
Vol 10 (12) ◽  
Author(s):  
Ayan Mukherjee ◽  
Romil Mehta ◽  
Soumen Saha ◽  
A. Bhattacharya ◽  
Pabitra Kumar Biswas ◽  
...  
Keyword(s):  
Thin Film ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Size Exclusion ◽  
Film Composite ◽  
Thin Film Composite ◽  
Gas And Liquid Chromatography ◽  
Pass Through ◽  
Polyamide Membrane ◽  
Trimesoyl Chloride

AbstractThe study evaluated removal efficiency of 43 pesticides from water by thin-film composite polyamide membrane indigenously prepared by interfacial polymerization of 1,3-phenylenediamine and 1,3,5 trimesoyl chloride coated on asymmetric polysulfone support. Membrane performance was evaluated by gas and liquid chromatography mass spectroscopy determination of multiple pesticides remaining in feed and permeated water following the application of pesticides each @ 0.02, 0.05, and 0.10 mg/L in de-ionized water. The membrane was most efficient in the rejection of persistent organochlorine insecticides, viz. endosulfans (100%), dichlorodiphenyltrichloroethane (95%), and hexachlorocyclohexane (92%). Out of 43 selected pesticides, 33 were removed by > 80%. Size exclusion mass transfer played a significant role for molecules to pass through the membrane as observed for endosulfan isomers, endosulfan sulphate, and difenoconazole with molecular weight > 400. Pesticide rejection was also related to hydrophobicity (Log P). Hydrophobic pesticides with log P > 4.5 were rejected by > 80%, while monocrotophos with less hydrophobicity (log P = − 0.22) exhibited poor rejection (38%). Water flux decreased with an increase in pesticide concentration. The process of pesticide filtration was optimized at 200 psi. The results indicated the potential of the membrane to remove pesticides from water.

scholarly journals Innovative Nanostructured Membranes for Reverse Osmosis Water Desalination

2020 ◽  
Author(s):  
Haleema Saleem ◽  
Syed Javaid Zaidi
Keyword(s):  
Reverse Osmosis ◽  
Separation Efficiency ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Water Desalination ◽  
Selective Layer ◽  
Salt Rejection ◽  
Membrane Performance ◽  
Tfc Membrane ◽  
Ro Membrane

Reverse osmosis (RO) is considered as the most widely utilized technique worldwide for water treatment. However, the commercial thin-film composite (TFC) membranes, which are normally made of polyamide (PA) through interfacial polymerization (IP), still experience certain major issues in performance and fabrication. The spin assisted layer-by-layer (SA-LbL) technique was established for overcoming some drawbacks with commercially available PA membranes. Also, recent investigations have recognized the nanoparticle inclusion into the selective layer as a powerful technique for improving the membrane efficiency. Hence, two different methodologies are presented here to improve the membrane performance, i.e., (1) SA-LbL technique to fabricate TFC membrane by the deposition of alternate ultrathin layers of different polyelectrolytes on polysulfone (PSF) commercial ultrafiltration membrane and (2) the nanoclay incorporation into the membranes during IP process to develop TFC membrane. Two types of nanoclays, cloisite (CS)-15A and montmorillonite (MNT), were incorporated to enhance the separation efficiency. This SA-LbL is an innovative method for the RO membrane manufacture, and has not been described earlier to the best of our knowledge. In addition, this work validated for the first time, the efficiency of the two nanoclays at the PA selective layer in the RO membrane. The membrane performance was evaluated using sodium chloride solution in a cross-flow permeation-testing cell for salt rejection and water flux. The results show significant improvement in water flux and salt rejection. The permeation test of 120 bilayers of poly (allylaminehydrochloride)/poly (vinylsulfate) on PSF substrate showed water flux of 37 L/ (m2.h) and salt rejection of 53%, for a 2000-ppm salt solution feed. The highest water flux of 40 L/m2.h with 80% salt rejection, relative to the control membrane was obtained for the membranes containing nanoclays at 25oC temperature, 40.0 bar pressure and 2000 ppm feed concentration. Thus, our study demonstrated that these TFC membranes are promising, and these novel fabrication techniques are great tool to manufacture the RO membrane.

scholarly journals Facile Fabrication of High-Performance Thin Film Nanocomposite Desalination Membranes Imbedded with Alkyl Group-Capped Silica Nanoparticles

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1415
Author(s):  
Biqin Wu ◽  
Shuhao Wang ◽  
Jian Wang ◽  
Xiaoxiao Song ◽  
Yong Zhou ◽  
...  
Keyword(s):  
Thin Film ◽  
Silica Nanoparticles ◽  
Brackish Water ◽  
Alkyl Group ◽  
High Performance ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Water Desalination ◽  
High Concentration ◽  
Thin Film Nanocomposite

The advantages of thin film nanocomposite reverse osmosis (TFN-RO) membranes have been demonstrated by numerous studies within the last decade. This study proposes a facile and novel method to tune the microscale and nanoscale structures, which has good potential to fabricate high-performance TFN-RO membranes. This method involves the addition of alkyl capped silica nanoparticles (alkyl-silica NPs) into the organic phase during interfacial polymerization (IP). We discovered for the first time that the high concentration alkyl-silica NPs in organic solvent isopar-G can limit the diffusion of MPD molecules at the interface, therefore shaping the intrinsic thickness and microstructures of the PA layer. Moreover, the alkyl group modification greatly reduces the NPs agglomeration and increases the compatibility between the NPs and the PA matrix. We further demonstrate that the doping of alkyl-silica NPs impacts the performance of the TFN-RO membrane by affecting intrinsic thickness, higher surface area, hydrophobic plugging effect, and higher surface charge by a series of characterization. At brackish water desalination conditions (2000 ppm NaCl, 1.55 MPa), the optimal brackish water flux was 55.3 L/m2∙h, and the rejection was maintained at 99.6%, or even exceeded this baseline. At seawater desalination conditions (32,000 ppm NaCl, 5.5 MPa), the optimized seawater flux reached 67.7 L/m2∙h, and the rejection was sustained at 99.4%. Moreover, the boron rejection was elevated by 11%, which benefits from a hydrophobic plugging effect of the alkyl groups.

scholarly journals Assessing the Performance of Thin-Film Nanofiltration Membranes with Embedded Montmorillonites

Membranes ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 79 ◽  
Author(s):  
Micah Belle Marie Yap Ang ◽  
Amira Beatriz Gaces Deang ◽  
Ruth R. Aquino ◽  
Blessie A. Basilia ◽  
Shu-Hsien Huang ◽  
...  
Keyword(s):  
Thin Film ◽  
Separation Efficiency ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Basal Spacing ◽  
Stable Performance ◽  
Pure Water Flux ◽  
Polyamide Membrane ◽  
Trimesoyl Chloride

In this study, the basal spacing of montmorillonite (MMT) was modified through ion exchange. Two kinds of MMT were used: sodium-modified MMT (Na-MMT) and organo-modified MMT (O-MMT). These two particles were incorporated separately into the thin-film nanocomposite polyamide membrane through the interfacial polymerization of piperazine and trimesoyl chloride in n-hexane. The membrane with O-MMT (TFNO-MMT) has a more hydrophilic surface compared to that of membrane with Na-MMT (TFNNa-MMT). When various types of MMT were dispersed in the n-hexane solution with trimesoyl chloride (TMC), O-MMT was well-dispersed than Na-MMT. The poor dispersion of Na-MMT in n-hexane led to the aggregation of Na-MMT on the surface of TFNNa-MMT. TFNO-MMT displayed a uniform distribution of O-MMT on the surface, because O-MMT was well-dispersed in n-hexane. In comparison with the pristine and TFNNa-MMT membranes, TFNO-MMT delivered the highest pure water flux of 53.15 ± 3.30 L∙m−2∙h−1 at 6 bar, while its salt rejection for divalent ions remained at 95%–99%. Furthermore, it had stable performance in wide operating condition, and it exhibited a magnificent antifouling property. Therefore, a suitable type of MMT could lead to high separation efficiency.

scholarly journals Tuning the Surface Structure of Polyamide Membranes Using Porous Carbon Nitride Nanoparticles for High-Performance Seawater Desalination

Membranes ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 163 ◽  
Author(s):  
Zongyao Zhou ◽  
Xiang Li ◽  
Digambar B. Shinde ◽  
Guan Sheng ◽  
Dongwei Lu ◽  
...  
Keyword(s):  
Thin Film ◽  
Porous Carbon ◽  
Carbon Nitride ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
The State ◽  
Seawater Desalination ◽  
Covalent Bonds ◽  
Salt Rejection ◽  
Positive Effects

Enhancing the water flux while maintaining the high salt rejection of existing reverse osmosis membranes remains a considerable challenge. Herein, we report the use of a porous carbon nitride (C3N4) nanoparticle to potentially improve both the water flux and salt rejection of the state-of-the-art polyamide (PA) thin film composite (TFC) membranes. The organic–organic covalent bonds endowed C3N4 with great compatibility with the PA layer, which positively influenced the customization of interfacial polymerization (IP). Benefitting from the positive effects of C3N4, a more hydrophilic, more crumpled thin film nanocomposite (TFN) membrane with a larger surface area, and an increased cross-linking degree of PA layer was achieved. Moreover, the uniform porous structure of the C3N4 embedded in the ”ridge” sections of the PA layer potentially provided additional water channels. All these factors combined provided unprecedented performance for seawater desalination among all the PA-TFC membranes reported thus far. The water permeance of the optimized TFN membrane is 2.1-folds higher than that of the pristine PA-TFC membrane, while the NaCl rejection increased to 99.5% from 98.0%. Our method provided a promising way to improve the performance of the state-of-art PA-TFC membranes in seawater desalination.

Sign in / Sign up

Export Citation Format

Share Document