scholarly journals Effect of La2O3 on the Microstructure and Grain Refining Effect of Novel Al-TiO2-C-XLa2O3 Refiners

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 182
Author(s):  
Huan Liu ◽  
Ruiying Zhang ◽  
Suying Yan ◽  
Jinxuan Li ◽  
Sen Yang
Keyword(s):  
Nucleation Temperature ◽  
The Novel ◽  
Grain Refining ◽  
Tio2 Powder ◽  
Sintering Process ◽  
Refining Effect ◽  
Transformation Time ◽  
Primary Transformation ◽  
Industrial Aluminum

New aluminum grain refiners, Al-TiO2-C-XLa2O3 refiners, were manufactured by the in situ reaction of Al powder, TiO2 powder, C powder, and La2O3 powder. The effects of La2O3 on the refiners’ microstructure and the grain refining effect of the Al-TiO2-C-XLa2O3 refiners on industrial aluminum were studied. The effect of the sintering process was also studied. The results show that the refiners contain Al3Ti, TiC, Al2O3, AlN, and Al20Ti2La. As the content of La2O3 increases, the amount of Al20Ti2La also increases. However, the amounts of Al3Ti, Al2O3, and TiC decrease. Al3Ti is a lath-like compound whose size becomes smaller. The distribution of Al2O3 and TiC, however, is more uniform. The Al-TiO2-C-0.2La2O3 refiner has the best grain refining effect on industrial aluminum. The size of the industrial aluminum refined by the Al-TiO2-C-0.2La2O3 refiner is 320 μm; the refiner’s grain size is 8.4% that of the industrial aluminum without refiners 0 μm (380). After adding the novel Al-TiO2-C-0.2La2O3 refiner, the nucleation temperature TN reached 679.21 °C, which is 17 °C above the nucleation temperature of the industrial aluminum without refiners. The primary transformation time is the longest at 25.5 s, which is 4.6 s higher than that of industrial aluminum (20.9 s). Furthermore, the ΔT of the aluminum is 0.5 °C, which is the lowest value.

scholarly journals Influence of protein (human galectin-3) design on aspects of lectin activity

2020 ◽  
Vol 154 (2) ◽  
pp. 135-153 ◽  
Author(s):  
Gabriel García Caballero ◽  
Donella Beckwith ◽  
Nadezhda V. Shilova ◽  
Adele Gabba ◽  
Tanja J. Kutzner ◽  
...  
Keyword(s):  
Protein Design ◽  
Full Range ◽  
Biological Information ◽  
The Novel ◽  
Modular Assembly ◽  
Binding Partners ◽  
Galectin 3 ◽  
Potential Applications ◽  
Similar Affinity

Abstract The concept of biomedical significance of the functional pairing between tissue lectins and their glycoconjugate counterreceptors has reached the mainstream of research on the flow of biological information. A major challenge now is to identify the principles of structure–activity relationships that underlie specificity of recognition and the ensuing post-binding processes. Toward this end, we focus on a distinct feature on the side of the lectin, i.e. its architecture to present the carbohydrate recognition domain (CRD). Working with a multifunctional human lectin, i.e. galectin-3, as model, its CRD is used in protein engineering to build variants with different modular assembly. Hereby, it becomes possible to compare activity features of the natural design, i.e. CRD attached to an N-terminal tail, with those of homo- and heterodimers and the tail-free protein. Thermodynamics of binding disaccharides proved full activity of all proteins at very similar affinity. The following glycan array testing revealed maintained preferential contact formation with N-acetyllactosamine oligomers and histo-blood group ABH epitopes irrespective of variant design. The study of carbohydrate-inhibitable binding of the test panel disclosed up to qualitative cell-type-dependent differences in sections of fixed murine epididymis and especially jejunum. By probing topological aspects of binding, the susceptibility to inhibition by a tetravalent glycocluster was markedly different for the wild-type vs the homodimeric variant proteins. The results teach the salient lesson that protein design matters: the type of CRD presentation can have a profound bearing on whether basically suited oligosaccharides, which for example tested positively in an array, will become binding partners in situ. When lectin-glycoconjugate aggregates (lattices) are formed, their structural organization will depend on this parameter. Further testing (ga)lectin variants will thus be instrumental (i) to define the full range of impact of altering protein assembly and (ii) to explain why certain types of design have been favored during the course of evolution, besides opening biomedical perspectives for potential applications of the novel galectin forms.

Experimental Investigation of Laser Sintering of Conductive Adhesive for Functional Prototypes Produced by Embedding Stereolithography

2014 ◽  
Vol 1038 ◽  
pp. 75-81
Author(s):  
Bernd Niese ◽  
Philipp Amend ◽  
Uwe Urmoneit ◽  
Stephan Roth ◽  
Michael Schmidt
Keyword(s):  
Thermal Damage ◽  
Laser Sintering ◽  
Conductive Adhesive ◽  
Flexible Production ◽  
Sintering Process ◽  
Building Process ◽  
In Situ Generation ◽  
Functional Components

Embedding stereolithography (eSLA) is an additive, hybrid process, which provides a flexible production of 3D components and the ability to integrate electrical and optical conductive structures and functional components within parts. However, the embedding of conductive circuits in stereolithography (SLA) parts assumes usage of process technologies, which enables their direct integration of conductive circuits during the layer-wise building process. In this context, a promising method for in-situ generation of conductive circuits is dispensing of conductive adhesive on the current surface of the SLA part and its subsequent sintering. In this paper, the laser sintering (λ = 355 nm) of conductive adhesive mainly consisting of silver nanoparticles is investigated. The work intends to evaluate the curing behavior of the conductive adhesive, the beam-matter-interactions and the thermal damage of the SLA substrate. The investigations revealed a fast and flexible laser sintering process for the generation of conductive circuits with sufficient electrical conductivity and sufficient current capacity load. In this context, a characterization of the conductive structures is done by measuring their electrical resistance and their potential current capacity load.

Ultrasound accelerated near-edge functionalized heterogeneous graphene oxide sonocatalyst for surface optical bandwidth efficacy and in-situ sonothermocatalysis

2021 ◽  
Author(s):  
Gopal Avashthi ◽  
Man Singh
Keyword(s):  
Graphene Oxide ◽  
The Novel ◽  
Surface Optical ◽  
Optical Bandwidth

Ultrasonochemically driven graphene oxide (GrO) functionalization (f) with Sulfanilamide (SA) near-edge catalyzed heterogeneous graphene oxide (h-GrO) as economic scalable f-(SA)GrO is reported. The novel in-situ H2O association was subsequently aligned...

scholarly journals Improvement of mechanical properties of HfB2-based composites by incorporating in situ SiC reinforcement through pressureless sintering

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
S. Ghadami ◽  
E. Taheri-Nassaj ◽  
H. R. Baharvandi ◽  
F. Ghadami
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Relative Density ◽  
Pressureless Sintering ◽  
Sintering Process ◽  
Vacuum Atmosphere ◽  
Sic Reinforcement ◽  
Microstructural Studies ◽  
Composite Samples

AbstractHfB2, Si, and activated carbon powders were selected to fabricate 0–30 vol% SiC reinforced HfB2-based composite. Pressureless sintering process was performed at 2050 °C for 4 h under a vacuum atmosphere. Microstructural studies revealed that in situ SiC reinforcement was formed and distributed in the composite according to the following reaction: Si + C = SiC. A maximum relative density of 98% was measured for the 20 vol% SiC containing HfB2 composite. Mechanical investigations showed that the hardness and the fracture toughness of these composites were increased and reached up to 21.2 GPa for HfB2-30 vol% SiC and 4.9 MPa.m1/2 for HfB2-20 vol% SiC, respectively. Results showed that alpha-SiC reinforcements were created jagged, irregular, and elongated in shape which were in situ formed between HfB2 grains and filled the porosities. Formation of alpha-SiC contributed to improving the relative density and mechanical properties of the composite samples. By increasing SiC content, an enhanced trend of thermal conductivity was observed as well as a reduced trend for electrical conductivity.

scholarly journals One-Pot Synthesis of Novel Multisubstituted 1-Alkoxyindoles

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1466
Author(s):  
Ye Eun Kim ◽  
Hyunsung Cho ◽  
Yoo Jin Lim ◽  
Chorong Kim ◽  
Sang Hyup Lee
Keyword(s):  
Alkyl Halide ◽  
The Novel ◽  
Reaction Conditions ◽  
One Pot ◽  
One Pot Synthesis ◽  
Consecutive Reactions ◽  
Intramolecular Condensation ◽  
Synthetic Sequence ◽  
Novel Target

Studies on a one-pot synthesis of novel multisubstituted 1-alkoxyindoles 1 and their mechanistic investigations are presented. The synthesis of 1 was successfully achieved through consecutive four step reactions from substrates 2. The substrates 2, prepared through a two-step synthetic sequence, underwent three consecutive reactions of nitro reduction, intramolecular condensation, and nucleophilic 1,5-addition to provide the intermediates, 1-hydroxyindoles 8, which then were alkylated in situ with alkyl halide to afford the novel target products 1. We optimized the reaction conditions for 1 focusing on the alkylation step, along with the consideration of formation of intermediates 8. The optimized condition was SnCl2·2H2O (3.3 eq) and alcohols (R1OH, 2.0 eq) for 1–2 h at 40 °C and then, base (10 eq) and alkyl halides (R2Y, 2.0 eq) for 1–4 h at 25–50 °C. Notably, all four step reactions were performed in one-pot to give 1 in good to modest yields. Furthermore, the mechanistic aspects were also discussed regarding the reaction pathways and the formation of side products. The significance lies in development of efficient one-pot reactions and in generation of new 1-alkoxyindoles.

scholarly journals A Study on the Effect of Alumina on the Morphology and Reduction Behavior of Sinter by In Situ Observation

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 740
Author(s):  
Sang Gyun Shin ◽  
Wan Ho Kim ◽  
Dong Joon Min
Keyword(s):  
Reduction Rate ◽  
Al2o3 Content ◽  
Confocal Laser ◽  
In Situ Observation ◽  
Sintering Process ◽  
Reduction Behavior ◽  
Reducing Gas ◽  
Interfacial Chemical Reaction ◽  
Reaction Routes

The effects of Al2O3 content on the morphology and reducibility of sinter were respectively investigated using confocal laser microscopy and thermogravimetric analysis at 1273 K under CO gas. To understand the effects of the sintering process, separate samples were prepared via the equilibrium and metastable reaction routes. In the equilibrium samples, the addition of Al2O3 led to the formation of the silico-ferrite of calcium and alumino phase and a decrease in the reduction rate due to the lowered reactivity of iron oxide. In contrast, in the metastable samples, the reduction rate increased after the addition of 2.5 mass% Al2O3. The addition of Al2O3 decreased the fraction of the liquid phase and increased the fraction of pores in the sample. As a result, the reduction rate is proportional to the Al2O3 content owing to the changes in the sinter morphology. In determining the reduction rate of the sinter, the influence of the microstructure on the diffusion of the reducing gas is more significant than that of the interfacial chemical reaction due to the formation of the SFCA phase. The microstructure changes of the sinter with the addition of Al2O3 and the corresponding reduction behaviors are further discussed.

scholarly journals Insertion of Phosphenium Ions into a Bicyclo[1.1.0]Tetraphosphabutane Iron Complex

Molecules ◽  
2021 ◽  
Vol 26 (13) ◽  
pp. 3920
Author(s):  
Martin Weber ◽  
Gábor Balázs ◽  
Alexander V. Virovets ◽  
Eugenia Peresypkina ◽  
Manfred Scheer
Keyword(s):  
Diffraction Analysis ◽  
Room Temperature ◽  
31P Nmr ◽  
Spectroscopic Studies ◽  
Iron Complex ◽  
The Novel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phosphenium Ions

By reacting [{Cp‴Fe(CO)2}2(µ,η1:1-P4)] (1) with in situ generated phosphenium ions [Ph2P][A] ([A]− = [OTf]− = [O3SCF3]−, [PF6]−), a mixture of two main products of the composition [{Cp‴Fe(CO)2}2(µ,η1:1-P5(C6H5)2)][PF6] (2a and 3a) could be identified by extensive 31P NMR spectroscopic studies at 193 K. Compound 3a was also characterized by X-ray diffraction analysis, showing the rarely observed bicyclo[2.1.0]pentaphosphapentane unit. At room temperature, the novel compound [{Cp‴Fe}(µ,η4:1-P5Ph2){Cp‴(CO)2Fe}][PF6] (4) is formed by decarbonylation. Reacting 1 with in situ generated diphenyl arsenium ions gives short-lived intermediates at 193 K which disproportionate at room temperature into tetraphenyldiarsine and [{Cp‴Fe(CO)2}4(µ4,η1:1:1:1-P8)][OTf]2 (5) containing a tetracyclo[3.3.0.02,7.03,6]octaphosphaoctane ligand.

In Situ Transformed Carbon Fibers/Al2O3 Nanocomposites Using Cao–MgO–SiO2 Sintering Agent

2021 ◽  
Vol 21 (10) ◽  
pp. 5235-5240
Author(s):  
Hua-Hui Chen ◽  
Jing-Jing Cao ◽  
Hai-Ping Hong ◽  
Nan Zheng ◽  
Jie Ren ◽  
...  
Keyword(s):  
Carbon Fibers ◽  
Axial Direction ◽  
Diffraction Peak ◽  
Sintering Process ◽  
Interface Bonding ◽  
The Core ◽  
Matrix Nanocomposites ◽  
Pan Fibers ◽  
Properties Of Composites

In Situ transformed carbon fibers/Al2O3 ceramic matrix nanocomposites with Cao–MgO–SiO2 sintering agent were prepared by hot-pressed sintering technology in vacuum. In the sintering process, pre-oxidized polyacrylonitrile fibers (below named as pre-oxidized PAN fibers) were used as the precursors of In Situ transformed carbon fibers. The micro/nanostructure of composites and interface between In Situ transformed carbon fibers and matrix were investigated, as well as the properties of composites. The results showed that the composites could be sintered well at a relatively low temperature of 1650 °C. During the sintering, the precursors, pre-oxidized PAN fibers, were In Situ transformed into carbon fibers, and the In Situ transformed carbon fibers had the graphitelike structure along the fiber axial direction. The carbon atoms arrangement in the surface layer of the fiber was more orderly than the core. A typical diffraction peak of carbon fiber at 26°, which corresponded to the (002) crystal plane, was observed, and the inter-planar spacing was approximately 0.34 nm. The CaO–MgO–SiO2 sintering agent formed MgAl2O4 and CaAl2Si2O8 phases in the interface between In Situ transformed carbon fibers and matrix, therefore improving the interface bonding, and thereby modifying the mechanical properties of the composites.

Sign in / Sign up

Export Citation Format

Share Document