scholarly journals Microstructure and Mechanical Properties of Multicomponent Metal Ti(C,N)-Based Cermets

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 927
Author(s):  
Xuelei Wang ◽  
Qiufeng Wang ◽  
Zhaojun Dong ◽  
Xiaoqian Zhou ◽  
Xiaoliang Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Energy Dispersive Spectrometry ◽  
Bending Strength ◽  
Binder Phase ◽  
X Ray Diffraction ◽  
Vacuum Sintering ◽  
X Ray ◽  
Weight Percentage ◽  
Microstructure And Mechanical Properties ◽  
Backscatter Scanning Electron Microscopy

Ti(C,N)-based cermets with multicomponent ingredients were prepared using vacuum sintering technology. The effect of molding agents, binder phase and sintering temperature on Ti(C,N)-based cermets were studied. The optimum molding performance was obtained by adding 2% polyvinyl alcohol (PVA-1788). The microstructure and mechanical properties of Ti(C,N)-based cermets were investigated. The Ti(C,N)-based cermet with a weight percentage of TiC:TiN:Ni:Co:Mo:WC:Cr3C2:C = 40:10:20:10:7:8:4:1 and sintered at 1450 °C had the optimal mechanical properties. The relative bending strength, Vickers hardness, elastic modulus and wear resistance were 2010 MPa, 15.01 GPa, 483.57 GPa and 27 mg, respectively. Additionally, X-ray diffraction (XRD), backscatter scanning electron microscopy pictures (SEM–BSE), energy dispersive spectrometry (EDS) and optical micrographs of Ti(C,N)-based cermets were characterized.

Microstructure and Mechanical Properties of TiB2-WC-TiC-Ni Composite Tool Materials

2012 ◽  
Vol 457-458 ◽  
pp. 1191-1195 ◽  
Author(s):  
Jin Peng Song ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Han Lian Liu ◽  
Jun Wang
Keyword(s):  
Mechanical Properties ◽  
Energy Dispersive Spectrometry ◽  
Interface Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tool Materials ◽  
Sintering Additive ◽  
Composite Tool ◽  
Microstructure And Mechanical Properties ◽  
Coarse Grains

TiB2-WC-TiC-Ni composite tool materials were fabricated using Ni as sintering additive by vacuum hot-pressing technique. The microstructure and mechanical properties of the composite were investigated. The composite was analyzed by scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive spectrometry (EDS). The microstructure of TiB2-WC-30wt.%TiC-Ni composite containing fine WC grains, TiC grains and uniform TiB2grains. A lot of pores and coarse grains were found in TiB2-WC-10wt.%TiC-Ni composite. The pores, brittle phases and the coarse grains were harmful to the improvement of the mechanical properties of the composite. The good wettability and the adequate liquid not only inhibited the formation of the pores and the coarse grains, but also strengthened the interface energy among the grains. The flexural strength, fracture toughness and Vickers hardness of TiB2-WC-30wt.%TiC-Ni composite were 996.6±113.6MPa, 7.64±0.28MPa•m1/2and 23.58±0.82GPa, respectively.

Microstructure and Mechanical Properties of Ti(C,N)-TiB2-WC Composite Ceramic Tool Materials

2012 ◽  
Vol 500 ◽  
pp. 673-678 ◽  
Author(s):  
Yue Liu ◽  
Chuan Zhen Huang ◽  
Han Lian Liu ◽  
Bin Zou ◽  
Qiang Shi
Keyword(s):  
Mechanical Properties ◽  
Energy Dispersive Spectrometry ◽  
Composite Ceramic ◽  
Hot Press ◽  
Ceramic Tool ◽  
Sintering Aids ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tool Materials ◽  
Microstructure And Mechanical Properties

Ti (C,N)-TiB2-WC composite ceramic tool materials with sintering aids such as Ni and Mo were fabricated at a temperature of 1550 °C for 1h sintering duration time in vacuum by a hot-press technique. The microstructure and mechanical properties were investigated. The composite ceramic tool materials were analyzed by means of scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive spectrometry (EDS). The main phases were composed of Ti (C, N), TiB2, WC and MoC, which indicated that no severe chemical reactions occurred in the composite. The flexural strength, fracture toughness and hardness of Ti (C,N)- 20 wt.%TiB2-WC ceramic material were 795.7 MPa, 6.4 MPa·m1/2 and 19.2 GPa respectively.

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Structure Characterization of Sintered CaO-Al2O3-SiO2 Glass-Ceramic Reinforced with Spodumene

2013 ◽  
Vol 834-836 ◽  
pp. 309-314
Author(s):  
Zi Fan Xiao ◽  
Jin Shu Cheng ◽  
Jun Xie
Keyword(s):  
Glass Ceramic ◽  
Energy Dispersive Spectrometry ◽  
Crystal Size ◽  
Bending Strength ◽  
Glass Ceramics ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
Crystalline Phases ◽  
X Ray

A glass-ceramic belonging to the CaO-Al2O3-SiO2(CAS) system with different composition of spodumene and doping the Li2O with amount between 0~2.5 % (mass fraction) were prepared by onestage heat treatment, under sintering and crystallization temperature at 1120 °C for two hours. In this paper, differential thermal analysis, X-ray diffraction, scanning electron microscopy, energy dispersive spectrometry and bending strength test were employed to investigate the microstructure and properties of all samples. β-wollastonite crystals were identified as the major crystalline phases, and increasing Li2O was found to be benefit for the crystallization and tiny crystalline phases remelting, resulting in the content of major crystalline phases increased first and then decreased with increasing the expense of spodumene. Meanwhile, the crystal size can be positively related with the content of Li2O. The preferable admixed dosage of spodumene can be obtained, besides the strength of glass-ceramics can be more than 90 MPa.

Microstructure and Mechanical Properties of Fe-Cu-Ni Sinters Prepared by Ball Milling and Hot Pressing

2020 ◽  
Vol 405 ◽  
pp. 379-384
Author(s):  
Joanna Borowiecka-Jamrozek ◽  
Jan Lachowski
Keyword(s):  
Mechanical Properties ◽  
Hot Pressing ◽  
High Hardness ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Composition ◽  
Microstructure And Mechanical Properties ◽  
Static Tensile ◽  
Iron Based ◽  
Surface Observations

The main purpose of this work was to determine the effect of the powder composition on the microstructure and properties of iron-based sinters used as a matrix in diamond tools. The Fe-Cu-Ni sinters obtained from a mixture of ground powders were used for experiments. The influence of manufacturing process parameters on the microstructure and mechanical properties of sinters was investigated. Sintering was performed using hot-pressing technique in a graphite mould. The investigations of obtained sinters included: density, hardness, static tensile test, X-ray diffraction analysis, microstructure and fracture surface observations. The obtained results indicate that the produced sinters have good plasticity and relatively high hardness.

scholarly journals Evaluation of Biomedical Ti/ZrO2 Joint Brazed with Pure Au Filler: Microstructure and Mechanical Properties

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 526
Author(s):  
Yuzhen Lei ◽  
Hong Bian ◽  
Wei Fu ◽  
Xiaoguo Song ◽  
Jicai Feng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Energy Dispersive Spectrometry ◽  
Filler Metal ◽  
Interfacial Microstructure ◽  
Holding Time ◽  
X Ray Diffraction ◽  
X Ray ◽  
Medical Products ◽  
Metallurgical Bonding ◽  
Brazed Joints

Titanium and zirconia (ZrO2) ceramics are widely used in biomedical fields. This study aims to achieve reliable brazed joints of titanium/ZrO2 using biocompatible Au filler for implantable medical products. The effects of brazing temperature and holding time on the interfacial microstructures and mechanical properties of titanium/Au/ZrO2 joints were fully investigated by scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS) and X-ray diffraction (XRD). The results indicated that the typical interfacial microstructure of the titanium/Au/ZrO2 joint was titanium/Ti3Au layer/TiAu layer/TiAu2 layer/TiAu4 layer/TiO layer/ZrO2 ceramic. With an increasing brazing temperature or holding time, the thickness of the Ti3Au + TiAu + TiAu2 layer increased gradually. The growth of the TiO layer was observed, which promoted metallurgical bonding between the filler metal and ZrO2 ceramic. The optimal shear strength of ~35.0 MPa was obtained at 1150 °C for 10 min. SEM characterization revealed that cracks initiated and propagated along the interface of TiAu2 and TiAu4 reaction layers.

Microstructure characterization and evaluation of mechanical properties of stir rheocast AA2024/TiB2 composite

2019 ◽  
Vol 54 (7) ◽  
pp. 981-997
Author(s):  
Semegn Cheneke ◽  
D Benny Karunakar
Keyword(s):  
Mechanical Properties ◽  
Dendritic Structure ◽  
Optical Microscope ◽  
X Ray Diffraction ◽  
Globular Structure ◽  
Cast Sample ◽  
X Ray ◽  
Weight Percentage ◽  
The Matrix ◽  
Fractured Surface

In this research, microstructure and mechanical properties of stir rheocast AA2024/TiB2 metal matrix composite have been investigated. The working temperature was 640℃, which was the selected semisolid temperature that corresponds to 40% of the solid fraction. Two weight percentage, 4 wt%, and 6 wt% of the TiB2 reinforcements were added to the matrix. The field emission scanning electron microscope micrographs of the developed composites showed a uniform distribution of the particles in the case of the 2 wt% and 4 wt% of the reinforcements. However, the particles agglomerated as the weight percentages of the reinforcement increases to 6%. The optical microscope of the liquid cast sample showed the dendritic structure, whereas the rheocast samples showed a globular structure. The X-ray diffraction analysis confirmed the distribution of the reinforcements in the matrix and the formation of some intermetallic compounds. Mechanical properties significantly improved by the addition of the reinforcements in the matrix. An increase in tensile strength of 13.3%, 40%, 28%, and 5% was achieved for the unreinforced rheocast sample, 2 wt%, 4 wt%, and 6 wt% reinforced rheocast samples respectively, compared to the liquid cast sample. An increase in 20% of hardness was attained for the composite with 2 wt% TiB2 compared to the liquid cast sample. According to the fractography analysis, small dimples were observed on the fractured surface of the unreinforced rheocast sample, whereas small and large voids were dominant on the fractured surface of the 2 wt% composite, which shows the ductile fracture mode.

Effect of AlN on Microstructure and Mechanical Properties of Mg-Al-Zn Alloy

2011 ◽  
Vol 704-705 ◽  
pp. 1095-1099
Author(s):  
Peng Liu ◽  
Hao Ran Geng ◽  
Zhen Qing Wang ◽  
Jian Rong Zhu ◽  
Fu Sen Pan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Tensile Testing ◽  
Cast Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Microstructure And Mechanical Properties ◽  
Zn Alloy

Effects of AlN addition on the microstructure and mechanical properties of as-cast Mg-Al-Zn magnesium alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile testing. Five different samples were made with different amounts of AlN(0wt%, 0.12wt%, 0.30wt%, 0.48wt%, 0. 60wt%). The results show that the phases of as-cast alloy are composed of α-Mg,β-Mg17Al12. The addition of AlN suppressed the precipitation of the β-phase. And, with the increase of AlN content, the microstructure of β-phase was changed from the reticulum to fine grains. When AlN content was up to 0.48wt% in the alloy, the β-phase became most uniform distribution. After adding 0.3wt% AlN to Al-Mg-Zn alloy, the average alloy grain size reduced from 102μm to 35μm ,the tensile strength of alloy was the highest. The average tensile strength increased from 139MPa to 169.91MPa, the hardness increased from 77.7HB to 98.4HB, but the elongation changes indistinctively. However, when more amount of AlN was added, the average alloy grain size did not reduce sequentially and increased to 50μm by adding 0.6wt% AlN and the β-phase became a little more. Keywords: Al-Mg-Zn alloy; AlN; β-Mg17Al12; Tensile strength

Fabrication and Mechanical Properties of SiC/Cu Composites with Zn Addition by Hot Pressing Sintering

2013 ◽  
Vol 745-746 ◽  
pp. 700-705
Author(s):  
Huang Liu ◽  
Guo Qiang Luo ◽  
Pin Gan Chen ◽  
Qiang Shen ◽  
Lian Meng Zhang
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Bending Strength ◽  
Coefficient Of Thermal Expansion ◽  
High Volume ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zn Addition ◽  
Hot Pressing Sintering

SiC/Cu composites exhibit low density, low coefficient of thermal expansion and excellent mechanical properties. In this study, Zn of 2 wt. % was added as the sintering activator, and the high volume faction (60%) SiC/Cu composites was fabricated by hot pressing sintering technology. The phase composition and morphology of as-prepare samples were characterized by X-ray diffraction (XRD) system and scanning electron microscopy (SEM) equipped with an energy-dispersive spectroscopy (EDS) system. The as-prepared SiC/Cu composites were dense and uniform as well as void free. The results show that SiC/Cu composites can reach excellent mechanical properties of SiC/Cu composites. With the increase of sintering temperature, Vickers hardness and the bending strength of the samples increased obviously and the as-prepared SiC/Cu composites achieved a maximum Vickers hardness and bending strength respectively of 195MPa and 140MPa.

Influence of Temperature of Accumulative Roll Bonding on the Microstructure and Mechanical Properties of AA5251 Aluminum Alloy

2014 ◽  
Vol 59 (1) ◽  
pp. 127-131 ◽  
Author(s):  
J. Bogucka
Keyword(s):  
Mechanical Properties ◽  
Ambient Temperature ◽  
Accumulative Roll Bonding ◽  
Bonding Temperature ◽  
Tensile Tests ◽  
Structure Evolution ◽  
X Ray Diffraction ◽  
Roll Bonding ◽  
X Ray ◽  
Microstructure And Mechanical Properties

Abstract The influence of bonding temperature on microstructure and mechanical properties of AA5251 alloy sheets have been analyzed in the paper. The alloy was deformed with the method of accumulative roll bonding (ARB) in various temperature conditions i.e. at ambient temperature up to 5th cycle (ε = 4.0) and using pre-heating of sheet packs at 200°C and 300°C up to 10 cycles (ε = 8.0). The deformed material was subjected to structural observations using TEM, measurements of crystallographic texture with the technique of X-ray diffraction and tensile tests. It was established that the temperature of roll-bonding had a significant effect on the structure evolution and the observed changes of mechanical properties. High refinement of microstructure and optimum mechanical properties were obtained for the material processed at lower temperatures, i.e. at ambient temperature and pre-heating at 200°C. Recovery structure processes occurring during deformation were observed in the alloy bonded with pre-heating at 300°C and therefore mechanical properties were lower than for the alloy bonded at lower temperatures.

Sign in / Sign up

Export Citation Format

Share Document