scholarly journals Effect of Solute Redistribution on Seeding Process of TiAl Alloys with Limited Convection in a Float Zone

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1525
Author(s):  
Yi-Long Xiong ◽  
Jun Shen ◽  
Yu-Jun Du

Two different analytic models, in which convection in the float zone is assumed, are developed to understand the solute redistributions during general seeding and quasi-seeding processes of TiAl alloys, respectively. The results suggest that the solute redistribution plays an important effect in the phase selection and microstructural development during the initial stage of seeding processes. In the initial stage of the quasi-seeding process, the interface concentration increases gradually and the solute diffusion boundary forms with the crystal growth of α phase. Correspondingly, a maximum constitutional undercooling with respect to β phase occurs ahead of the solidifying α interface and then decreases gradually. Simultaneously, the position where the maximum constitutional undercooling occurs also moves forward with regard to the interface. While in the initial stage of the general seeding process, the α phase can grow continuously as stable phase when the initial composition of the melt is higher than Al 48.9%. Under the influence of both the constitutional undercooling and Ti5Si3 particles, coarse dendrites form and then are transformed to cellular morphology. Nevertheless, the lamellar microstructure can still be aligned well during the entire seeding process. Besides, it is also found that the thickness of solute diffusion boundary decreases with the increase of convection intensity and thus, the growing interface become more stably correspondingly, which is beneficial to the lamellar alignment of TiAl alloys.

2002 ◽  
Vol 753 ◽  
Author(s):  
S. W. Kim ◽  
H. N. Lee ◽  
M. H. Oh ◽  
M. Yamaguchi ◽  
D. M. Wee

ABSTRACTThe thermal stability of lamellar microstructure in Ti-Al-Mo PST crystals containing C or Si, was investigated. In addition, the variation of α-phase volume fraction in Ti-Al-Mo-(C,Si) systems was investigated at several temperatures. Ti-46Al-1.5Mo-0.2C and Ti-46Al-1.5Mo-1.0Si alloys were found to be very stable during heat treatments at various heating rates and temperatures. Moreover, the α-phase volume fractions of Ti-46Al-1.5Mo-0.2C and Ti-46Al-1.5Mo-1.0Si alloys, which were stable compositions, changed less than those of Ti-47Al and Ti-46–1.5Mo alloys, which were unstable compositions. From these results, it was determined that the instability of the latter alloys was caused by their relatively higher variation of α-phase volume fraction during heating. Therefore, it is suggested that the variation of α-phase volume fraction is an important factor in controlling the thermal stability of lamellar microstructure.


2015 ◽  
Vol 59 ◽  
pp. 87-94 ◽  
Author(s):  
H.Z. Niu ◽  
Y.Y. Chen ◽  
Y.S. Zhang ◽  
J.W. Lu ◽  
W. Zhang ◽  
...  

Author(s):  
P. R. Okamoto ◽  
N.Q. Lam ◽  
R. L. Lyles

During irradiation of thin foils in a high voltage electron microscope (HVEM) defect gradients will be set up between the foil surfaces and interior. In alloys defect gradients provide additional driving forces for solute diffusion since any preferential binding and/or exchange between solute atoms and mobile defects will couple a net flux of solute atoms to the defect fluxes. Thus, during irradiation large nonequilibrium compositional gradients can be produced near the foil surfaces in initially homogeneous alloys. A system of coupled reaction-rate and diffusion equations describing the build up of mobile defects and solute redistribution in thin foils and in a semi-infinite medium under charged-particle irradiation has been formulated. Spatially uniform and nonuniform damage production rates have been used to model solute segregation under electron and ion irradiation conditions.An example calculation showing the time evolution of the solute concentration in a 2000 Å thick foil during electron irradiation is shown in Fig. 1.


Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 163
Author(s):  
Shu Wang ◽  
Yilong Liang ◽  
Hao Sun ◽  
Xin Feng ◽  
Chaowen Huang

The main objective of the present study was to understand the oxygen ingress in titanium alloys at high temperatures. Investigations reveal that the oxygen diffusion layer (ODL) caused by oxygen ingress significantly affects the mechanical properties of titanium alloys. In the present study, the high-temperature oxygen ingress behavior of TC21 alloy with a lamellar microstructure was investigated. Microstructural characterizations were analyzed through optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Obtained results demonstrate that oxygen-induced phase transformation not only enhances the precipitation of secondary α-phase (αs) and forms more primary α phase (αp), but also promotes the recrystallization of the ODL. It was found that as the temperature of oxygen uptake increases, the thickness of the ODL initially increases and then decreases. The maximum depth of the ODL was obtained for the oxygen uptake temperature of 960 °C. In addition, a gradient microstructure (αp + β + βtrans)/(αp + βtrans)/(αp + β) was observed in the experiment. Meanwhile, it was also found that the hardness and dislocation density in the ODL is higher than that that of the matrix.


2021 ◽  
Vol 1035 ◽  
pp. 182-188
Author(s):  
Jian Hua Cai ◽  
She Wei Xin ◽  
Lei Li ◽  
Lei Zou ◽  
Hai Ying Yang ◽  
...  

The plastic deformation mechanism of Ti-55531 alloy with bimodal microstructure was investigated by compression testing at room temperature. The bimodal microstructure was composed of equiaxed primary α phase (αp) and transformed β (βtrans) that consisted of acicular secondary α phase (αs) and residual β phase (βr). In the initial stage of deformation, the αp grains first underwent plastic deformation, the dislocations germinated and increased, forming the dislocation loop with the dislocation free zone in αp at the true stain of 0.083. With the true strain subsequently increasing to 0.105, the dislocation tangle and dislocation pile-up occurred in αp, and a lot of dislocations were also activated in most of αs. Moreover, the dislocation density was increasing gradually in βr with the adding of strain. Finally, the dislocation pile-up and dislocation tangle appeared in αs and βr at the true strain of 0.163. The whole deformation process was coordinated by αp, αs and βr. They accommodated mutually and completed deformation together.


2013 ◽  
Vol 668 ◽  
pp. 870-874
Author(s):  
Heng Min Ding ◽  
Tie Qiao Zhang ◽  
Lv Chun Pu

In the paper, a model basing on solute conservative in every unit is developed for solving the solute diffusion equation during solidification. The model includes time-dependent calculations for temperature distribution, solute redistribution in the liquid and solid phases. Three-dimensional computations are performed for Al-Cu dendritic growth into an adiabatic and highly supersaturated liquid phase. A numerical algorithm was developed to explicitly track the sharp solid/liquid (S/L) interface on a fixed Cartesian grid. Three-dimensional mesoscopic calculations were performed to simulate the evolution of equiaxed dendritic morphologies.


2016 ◽  
Vol 258 ◽  
pp. 501-505
Author(s):  
Alice Chlupová ◽  
Milan Heczko ◽  
Karel Obrtlík ◽  
Přemysl Beran ◽  
Tomáš Kruml

Two γ-based TiAl alloys with 7 at.% of Nb, alloyed with 2 at.% Mo and 0.5 at.% C, were studied. A heat treatment leading to very fine lamellar microstructure was applied on both alloys. Microstructure after the heat treatment was described and mechanical properties including fatigue behaviour were measured. The as-received material alloyed with C possesses high strength and very limited ductility, especially at RT. After application of selected heat treatment it becomes even more brittle; therefore, this process could be considered as not appropriate for this alloy. On the contrary, in the case of Mo alloyed material, both strength and ductility are improved by the heat treatment at RT and usual working temperature (~750 °C). Presence of the β phase is responsible for this effect. The selected heat treatment thus can be an alternative for this alloy to other thermomechanical treatments as high temperature forging.


Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1703
Author(s):  
Marzena M. Lachowicz ◽  
Robert Jasionowski

The main purpose of this work was to experimentally determine the effect of the cooling rate during the eutectoid transformation on the corrosion resistance of a hypoeutectic Zn-4Al cast alloy in 5% NaCl solution. This was considered in relation to the alloy microstructure. For this purpose, metallographic and electrochemical studies were performed. It was found that the faster cooling promoted the formation of finer (α + η) eutectoid structures, which translated into a higher hardness and lower corrosion current density. In the initial stage of corrosion processes the eutectoid structure in the eutectic areas were attacked. At the further stages of corrosion development, the phase η was dissolved, and the α phase appears to be protected by the formation of corrosion products.


2013 ◽  
Vol 747-748 ◽  
pp. 38-43 ◽  
Author(s):  
Li Hua Chai ◽  
Liang Yang ◽  
Jian Peng Zhang ◽  
Zhi Yong Zhang ◽  
Lai Qi Zhang ◽  
...  

High Nb containing TiAl alloys have been investigated traditionally as potential high temperature structural materials because of their high strength, good oxidation and creep resistance. However, the poor ductility and fracture toughness at room temperature limit their application, which could be improved by controlling microstructure to get refine and homogeneous fully lamellar structure. In this study, a high Nb containing TiAl alloy alloying Mn, B and Y with refined microstructure was produced. The solidification path was analyzed by DSC and SEM microstructure of the alloy was observed, after heating at a certain temperature for 1-24hrs and then quenching in water. The dissolution of β phase was also investigated. The results showed that the β phase could decompose only by heating in single β or near α phase field.


Sign in / Sign up

Export Citation Format

Share Document