scholarly journals Assessment of the Heat Input Effect on the Distribution of Temperature Cycles in the HAZ of S460MC Welds in MAG Welding

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1954
Author(s):  
Jaromír Moravec ◽  
Martin Švec ◽  
Šárka Bukovská ◽  
Jiří Sobotka
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Mathematical Description ◽  
Heat Input ◽  
Sufficient Accuracy ◽  
Maximum Temperature ◽  
Specific Location ◽  
Temperature Cycles ◽  
Weld Pool Geometry ◽  
Basic Parameters

Temperature cycles generated during welding have a significant effect on the changes in the HAZ of welds, regardless of whether these are changes in structure or mechanical properties; however, it is problematic to obtain temperature cycles with sufficient accuracy across the entire HAZ so that they can be generally taken and used in welding simulations and for real experiments of processes occurring in HAZ. In particular, for a study in a specific location, it is important to know the maximum temperature of the cycle and the cooling rate defined mainly by the parameter t8/5. No studies in which anybody tries to find a mathematical description defining the basic parameters of temperature cycles in the HAZ could be found in the performed research. Therefore, the study presented in this paper results in a mathematical description defining the dependence of achieved maximum temperature on the distance from the fusion line in the HAZ of S460MC welds and with heat input values in the interval from 8 to 14 kJ·cm−1. Moreover, this paper presents the influence of heat input value on the weld pool geometry, including the effect of heat input value on grain coarsening in the highly heated HAZ.

scholarly journals Effect of Welding Thermal Cycles on Microstructure and Mechanical Properties of Multi-Strand Composite Welding Wire Welded Joints of High Nitrogen Austenitic Stainless Steel

2019 ◽  
Author(s):  
jianguo Li ◽  
Huan Li ◽  
Yu Liang ◽  
Pingli Liu ◽  
Lijun Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Welded Joints ◽  
Heat Input ◽  
Weld Seam ◽  
High Heat ◽  
High Nitrogen ◽  
Welding Wire ◽  
Delta Ferrite ◽  
High Heat Input

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (GRD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M23C6 precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M23C6.

scholarly journals Effect of Heat Input and Undermatched Filler Wire on the Microstructure and Mechanical Properties of Dissimilar S700MC/S960QC High-Strength Steels

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 883 ◽  
Author(s):  
Francois Njock Bayock ◽  
Paul Kah ◽  
Belinga Mvola ◽  
Pavel Layus
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Volume Fraction ◽  
Base Material ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructure And Mechanical Properties

The effect of heat input on the microstructure and mechanical properties of dissimilar S700MC/S960QC high-strength steels (HSS) using undermatched filler material was evaluated. Experiments were performed using the gas metal arc welding process to weld three samples, which had three different heat input values (i.e., 15 kJ/cm, 7 kJ/cm, and 10 kJ/cm). The cooling continuous temperature (CCT) diagrams, macro-hardness values, microstructure formations, alloy element compositions, and tensile test analyses were performed with the aim of providing valuable information for improving the strength of the heat-affected zone (HAZ) of both materials. Micro-hardness measurement was conducted using the Vickers hardness test and microstructural evaluation by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The mechanical properties were characterized by tensile testing. Dissimilar welded samples (S700MC/S960QC) with a cooling rate of 10 °C/s (15 kJ/cm) showed a lower than average hardness (210 HV5) in the HAZ of S700MC than S960QC. This hardness was 18% lower compared to the value of the base material (BM). The best microstructure formation was obtained using a heat input of 10 kJ/cm, which led to the formation of bainite (B, 60% volume fraction), ferrite (F, 25% volume fraction), and retained austenite (RA, 10%) in the final microstructure of S700MC, and B (55%), martensite (M, 45%), and RA (10%), which developed at the end of the transformation of S960QC. The results showed the presence of 1.3 Ni, 0.4 Mo, and 1.6 Mn in the fine-grain heat-affected zone of S700MC. The formation of a higher carbide content at a lower cooling rate reduced both the hardness and strength.

scholarly journals The Microstructure and Mechanical Properties of Multi-Strand, Composite Welding-Wire Welded Joints of High Nitrogen Austenitic Stainless Steel

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2944 ◽  
Author(s):  
Jianguo Li ◽  
Huan Li ◽  
Yu Liang ◽  
Pingli Liu ◽  
Lijun Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Welded Joints ◽  
Heat Input ◽  
Weld Seam ◽  
High Heat ◽  
High Nitrogen ◽  
Welding Wire ◽  
Δ Ferrite ◽  
High Heat Input

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor, and lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated Goss (GRD) ({110}⟨1 1 ¯ 0⟩) orientation of a thin plate and the cube (C) ({001}⟨100⟩) orientation of a thick plate are obvious after welding, but the S ({123}⟨63 4 ¯ ⟩) orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It was observed that low heat input and a high cooling rate results in an increase of δ-ferrite, and a high dislocation density was obtained in grain boundaries of δ-ferrite. M23C6 precipitates due to a low cooling rate and heat input in the weld seam and deteriorates the elongation of welded joints. The engineering Stress–strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M23C6.

scholarly journals Influence of Welding Parameters and Filler Material on the Mechanical Properties of HSLA Steel S960MC Welded Joints

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 305
Author(s):  
Miloš Mičian ◽  
Martin Frátrik ◽  
Daniel Kajánek
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Welded Joints ◽  
Heat Input ◽  
Arc Welding ◽  
Hsla Steel ◽  
Filler Material ◽  
Welding Parameters ◽  
Thick Sheet ◽  
Soft Zone

This article provides an overview of the influence of welding parameters and filler material on changes in the heat-affected zone (HAZ) of thermo-mechanically controlled processed (TMCP) steel welded joints. The research focused on evaluating the effect of heat input and cooling rate on the width of the soft zone, which significantly affects the mechanical properties of welded joints. The negative effect of the soft zone is more pronounced as the thickness of the material decreases. Therefore, the object of this research was a 3-mm-thick sheet of S960MC steel welded by gas metal arc welding (GMAW) and metal-cored arc welding (MCAW) technology. Variable welding parameters were reflected in different heat input and cooling rate values, which led to a change in the properties of the HAZ and thus the mechanical properties of the welded joints. The changes in the HAZ were analyzed by microscopic analysis and mechanical testing. The measured results showed a significant effect of heat input on the cooling rate, which considerably affected the width of the soft zone in the HAZ and thus the overall mechanical properties of the welded joints.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process

2021 ◽  
pp. 095440622199840
Author(s):  
Yashwant Koli ◽  
N Yuvaraj ◽  
Aravindan Sivanandam ◽  
Vipin
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Large Scale ◽  
High Deposition Rate ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Cold Metal Transfer ◽  
Geometrical Shapes ◽  
Wire Arc Additive Manufacturing

Nowadays, rapid prototyping is an emerging trend that is followed by industries and auto sector on a large scale which produces intricate geometrical shapes for industrial applications. The wire arc additive manufacturing (WAAM) technique produces large scale industrial products which having intricate geometrical shapes, which is fabricated by layer by layer metal deposition. In this paper, the CMT technique is used to fabricate single-walled WAAM samples. CMT has a high deposition rate, lower thermal heat input and high cladding efficiency characteristics. Humping is a common defect encountered in the WAAM method which not only deteriorates the bead geometry/weld aesthetics but also limits the positional capability in the process. Humping defect also plays a vital role in the reduction of hardness and tensile strength of the fabricated WAAM sample. The humping defect can be controlled by using low heat input parameters which ultimately improves the mechanical properties of WAAM samples. Two types of path planning directions namely uni-directional and bi-directional are adopted in this paper. Results show that the optimum WAAM sample can be achieved by adopting a bi-directional strategy and operating with lower heat input process parameters. This avoids both material wastage and humping defect of the fabricated samples.

scholarly journals Substantiation of technical and operational characteristics of the device to sort corn cobs

2020 ◽  
Vol 17 ◽  
pp. 00094
Author(s):  
Dmitry N. Byshov ◽  
Irina A. Petunina ◽  
Elena A. Kotelevskaya ◽  
Sergey N. Borychev ◽  
Georgy K. Rembalovich
Keyword(s):  
Mechanical Properties ◽  
Technological Parameters ◽  
Corn Cobs ◽  
Operational Characteristics ◽  
Basic Parameters ◽  
Treated Plant ◽  
Working Bodies

The paper presents a method to substantiate the technical and technological parameters of the device to sort corn cobs, which takes into account the biometric and physical-mechanical properties of the treated plant objects. The method of basic parameters substantiation involves determining the overall dimensions of the device, the geometric and technological parameters of the working bodies, as well as the energy for operation.

scholarly journals Influence of the Heat Input on the Dendritic Solidification Structure and the Mechanical Properties of 2.25Cr-1Mo-0.25V Submerged-Arc Weld Metal

2021 ◽  
Author(s):  
Hannah Schönmaier ◽  
Ronny Krein ◽  
Martin Schmitz-Niederau ◽  
Ronald Schnitzer
Keyword(s):  
Mechanical Properties ◽  
Weld Metal ◽  
Heat Input ◽  
Stress Rupture ◽  
Pressure Vessels ◽  
Rupture Time ◽  
Solidification Structure ◽  
Welding Parameters ◽  
Austenite Grain Size ◽  
Submerged Arc

AbstractThe alloy 2.25Cr-1Mo-0.25V is commonly used for heavy wall pressure vessels in the petrochemical industry, such as hydrogen reactors. As these reactors are operated at elevated temperatures and high pressures, the 2.25Cr-1Mo-0.25V welding consumables require a beneficial combination of strength and toughness as well as enhanced creep properties. The mechanical properties are known to be influenced by several welding parameters. This study deals with the influence of the heat input during submerged-arc welding (SAW) on the solidification structure and mechanical properties of 2.25Cr-1Mo-0.25V multilayer metal. The heat input was found to increase the primary and secondary dendrite spacing as well as the bainitic and prior austenite grain size of the weld metal. Furthermore, it was determined that a higher heat input during SAW causes an increase in the stress rupture time and a decrease in Charpy impact energy. This is assumed to be linked to a lower number of weld layers, and therefore, a decreased amount of fine grained reheated zone if the multilayer weld metal is fabricated with higher heat input. In contrast to the stress rupture time and the toughness, the weld metal’s strength, ductility and macro-hardness remain nearly unaffected by changes of the heat input.

Sign in / Sign up

Export Citation Format

Share Document