scholarly journals Improving Machining Localization and Surface Roughness in Wire Electrochemical Micromachining Using a Rotating Ultrasonic Helix Electrode

Micromachines ◽  
2020 ◽  
Vol 11 (7) ◽  
pp. 698
Author(s):  
Siying Ling ◽  
Minghao Li ◽  
Yong Liu ◽  
Kan Wang ◽  
Yong Jiang
Keyword(s):  
Surface Roughness ◽  
Aspect Ratio ◽  
Ultrasonic Vibration ◽  
304 Stainless Steel ◽  
Electrochemical Micromachining ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machined Surface ◽  
Wire Electrochemical Micromachining ◽  
Ultrasonic Assisted

Wire electrochemical micromachining (WECMM) technology is regarded a promising method to fabricate high aspect ratio microstructures on hard-to-machining materials, however, the by-product accumulation in the machining gap limits its application. In this paper, a new method called ultrasonic-assisted wire electrochemical micromachining (UA-WECMM) is proposed to improve the machining performance of WECMM. Firstly, a flow-field simulation in the machining gap was carried out; the results showed that the ultrasonic vibration of electrode can remarkably enhance the mass transport in the machining gap and improve the machining condition. Secondly, experiments were performed to confirm the effect of ultrasonic vibration, which illustrated that the vibration with proper amplitude can reduce the slit width and improve the morphology of machined surface. Moreover, the influence of other machining parameters were also discussed. Finally, a T-type micro connector with good surface roughness (Ra 0.286 μm) was fabricated on a 300-μm-thick 304 stainless steel workpiece and a micro gear (diameter: 3.362 mm; Ra: 0.271 μm) with an aspect ratio of 7 was fabricated on a 2-mm-thick workpiece. It is proved that the proposed ultrasonic-assisted wire electrochemical micromachining method has considerable potential and broad application prospects.

Multi Objective Optimization of Cutting Parameters in Machining Cellulose Based Hybrid Composites

2015 ◽  
Vol 761 ◽  
pp. 287-292
Author(s):  
Raja Izamshah ◽  
Zainudin Zuraidah ◽  
Mohd Shahir Kasim ◽  
M. Hadzley ◽  
M. Amran
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Hybrid Composites ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Multi Objective Optimization ◽  
Machining Performance ◽  
Machined Surface ◽  
Multi Objective ◽  
Optimization Of Cutting Parameters

Cellulose based hybrid composites are gaining popularity in the growing green communities. With extensive studies and increasing applications for future advancement, the need for an accurate and reliable guidance in machining this type of composites has increased enormously. Smooth and defect free machined surface are always the ultimate objectives. The present work deals with the study of machining parameters (i.e. spindle speed, feed rate and depth of cut) and their effects on machining performance (i.e. surface roughness and delamination) to establish an optimized setup of machining parameters in achieving multi objective machining performance. Cellulose based hybrid composites consist of jute (a bast fiber) and glass fiber embedded in polyester resins. Response Surface Methodology (RSM) using Box-Behnken Design (BBD) was chosen as the design of experiment approach for this study. Based on that experimental approach, 17 experimental runs were conducted. Mathematical model for each response was developed based on the experimental data. Adequacy of the models were analyzed statistically using Analysis of Variance (ANOVA) in determining the significant input variables and possible interactions. The multi objective optimization was performed through numerical optimization, and the predicted results were validated. The agreement between the experimental and selected solution was found to be strong, between 95% to 96%, thus validating the solution as the optimal machining condition. The findings suggest that feed rate was the main factor affecting surface roughness and delamination .

Comparative Study and Mathematical Modeling of Machining Parameters in Ultrasonic-Assisted EDM of AISI H13 Tool Steel by the Application of Workpiece Vibration

2010 ◽  
Vol 154-155 ◽  
pp. 1604-1613
Author(s):  
Mohammad Reza Shabgard ◽  
Babak Sadizadeh ◽  
Keivan Amini ◽  
Hamid Pourziaie
Keyword(s):  
Comparative Study ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Correct Selection ◽  
Machining Parameters ◽  
Machining Performance ◽  
Ultrasonic Assisted ◽  
Aisi H13

The correct selection of the machining parameters is one of the most significant issues to take into consideration in Ultrasonic-assisted Electrical Discharge Machining (US-EDM) and EDM processes. In the present work, a study has been made to develop and extract statistical models to show the relationship between important machining performance data (material removal rate (MRR), tool wear ratio (TWR) and surface roughness Ra) and the input machining parameters (pulse current, and pulse-on time) in the EDM and US-EDM of AISI H13. The models obtained were used to analyze the effects of input parameters on machining performance. In addition, a comparative study was carried out to investigate the effect of ultrasonic vibration of the workpiece on machining performance. The results show that Ultrasonic vibration of the workpiece can significantly reduce the inactive pulses and improves the stability of process. Also US-EDM is effective in attaining a high material removal rate (MRR) in finishing regime in comparison with conventional EDM. The results of Analysis of Variance (ANOVA) indicate that the proposed mathematical models can adequately explain the performance within the limits of the factors being studied.

scholarly journals Electrochemical Microslot Machining by Ultrasonic-Vibration-Aided Electrolyte on Nitinol Wire

Processes ◽  
2021 ◽  
Vol 9 (10) ◽  
pp. 1752
Author(s):  
Jung-Chou Hung ◽  
Po-Jen Yang
Keyword(s):  
Ultrasonic Vibration ◽  
Electrochemical Micromachining ◽  
Machining Accuracy ◽  
Machining Parameters ◽  
Power Generator ◽  
Nitinol Wire ◽  
Wire Electrochemical Micromachining ◽  
Titanium Wire ◽  
Pulse Power Generator ◽  
Machining Characteristics

In this research, the main purpose was to study the applicability of a machining method on microscale medical-equipment manufacturing. The characteristics of wire electrochemical micromachining (WECMM) against NiTi 50-50 wire was investigated. The study utilized a tungsten wire 0.03 mm in diameter as an electrode to cut a fine slot into the nickel–titanium wire. In order to reach a high-precision WECMM finish, an ultrashort pulse power generator was used as a power source to minimize the stray current effect, thus improving the machining accuracy. During the process, various machining parameters were tested for their effects on machining characteristics. In addition, ultrasonic-vibration-aided WECMM was investigated to determine whether it benefited the machining characteristics. The experiment’s results showed that under such an experiment setting, microslots can be successfully manufactured. Furthermore, with the advance adjustment of experimental parameters, the machining accuracy was improved. Finally, a fine slot was manufactured under the optimum experiment parameters and aided by ultrasonic vibration.

Study on Effect of Ultrasonic Vibration in Machining of Alumina Ceramic

2012 ◽  
Vol 516 ◽  
pp. 311-316 ◽  
Author(s):  
Kyung Hee Park ◽  
Kyeong Tae Kim ◽  
Yun Hyuck Hong ◽  
Hon Jong Choi ◽  
Young Jae Choi
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Ultrasonic Vibration ◽  
Cutting Forces ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Ultrasonic Machining ◽  
Machining Performance ◽  
Machined Surface ◽  
Combination Technique

Ultrasonic machining can be applied for the machining of difficult-to-cut materials using ultrasonical oscillation in an axial direction on top of tool rotation, which can cause reduction of cutting temperature and tool wear. In this study, the experiments were performed on a DMG ULTRASONIC 20 linear machine tool using diamond tools in both conventional and ultrasonic vibration assisted machining. The machining performance was evaluated and compared for both cases in terms of cutting forces, machined surface roughness and tool wear. And the combination technique of 3D surface topography measurement and image processing was applied for the tool wear progress. Overall, the experimental results showed that ultrasonic machining had less tool wear and lower cutting forces at low cutting speed compared to conventional machining. Also surface roughness was slightly lower in ultrasonic machining than that without ultrasonic vibration.

scholarly journals Theoretical and Experimental Investigation Into The Machining Performance in Axial Ultrasonic Vibration–Assisted Cutting of Ti6Al4V

2021 ◽  
Author(s):  
He Sui ◽  
Lifeng Zhang ◽  
Shuang Wang ◽  
Zhaojun Gu
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Influencing Factors ◽  
Ultrasonic Vibration ◽  
Tool Life ◽  
Feed Rate ◽  
Rotation Speed ◽  
Machining Parameters ◽  
Machining Performance ◽  
Cutting Depth

Abstract Axial ultrasonic vibration-assisted cutting (AUVC) has proved to have better machining performance compared with conventional cutting methods; however, the effect of numerous and complex influencing factors on machining performance has not been clearly revealed and a recommended combination of cutting conditions has not been proposed yet, especially for difficult-to-machine material such as Ti6Al4V alloy. This paper focuses on experimental and theoretical investigation into machining performance when cutting Ti6Al4V with the AUVC method. First, a retrospective of the separation characteristics of AUVC is provided and the variable parameter cutting characteristics are demonstrated. We classify the influencing factors on machining performance into four categories: machining parameters, vibration parameters, tool choice, and cooling conditions. The relationship between these factors in terms of their effect on machining performance is established theoretically. Then, it describes experiments to determine the influence of these factors on cutting force, tool life, and surface roughness. For absolute influence, the orders for cutting force, tool life, and surface roughness are respectively cutting depth > amplitude > feed rate > rotation speed, rotation speed > feed rate > amplitude > cutting depth, and feed rate > amplitude > cutting depth > rotation speed. However, for relative influence, the order is unified as: amplitude > feed rate > rotation speed > cutting depth. Finally, it suggests a smaller feed rate, larger amplitude, moderate rotation speed, and smaller cutting depth in addition to a WC tool coated with TiAlN and used under HPC cooling condition for optimal performance of AUVC. This recommendation is based on the theoretical analysis and experimental results of cutting force, surface roughness, and tool life.

scholarly journals Research on the Formation Mechanism of Surface Morphology in Three-Excitation Ultrasonic Spatial Vibration-Assisted Turning

2022 ◽  
Author(s):  
Jingwei Duan ◽  
Ping Zou ◽  
Shiyu Wei ◽  
Rui Fang ◽  
Liting Fang
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Cutting Speed ◽  
Vertical Direction ◽  
Lower Surface ◽  
Machining Parameters ◽  
Machining Performance ◽  
Spatial Vibration ◽  
Vibration Parameters ◽  
Turning System

Abstract To improve the machining performance of different processing materials, a three-excitation ultrasonic spatial vibration-assisted turning system is proposed, which realizes the non-unity of the plane where the cutting trajectory of the tool is located. The influence and formation law of three-excitation ultrasonic spatial vibration-assisted turning on the surface roughness of the workpiece under different vibration parameters (amplitude) and machining parameters (cutting speed, cutting depth, and feed) were analyzed by response surface methodology. The results show that in terms of vibration parameters, the influence of ultrasonic vibration applied in the horizontal direction on surface roughness is significantly greater than that of ultrasonic vibration applied in the vertical direction, while the feed has the greatest influence on surface roughness, followed by cutting speed. The surface roughness of common turning, one-dimensional ultrasonic vibration-assisted turning, ultrasonic elliptical vibration-assisted turning, and three-excitation ultrasonic spatial vibration-assisted turning were theoretically analyzed and experimentally compared. The results show that compared with the other three turning methods, the three-excitation ultrasonic spatial vibration-assisted turning can obtain a lower surface roughness and have good machinability.

scholarly journals Experimental Study on Ultrasonic Vibration-Assisted WECDM of Glass Microstructures with a High Aspect Ratio

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 125
Author(s):  
Yan Chen ◽  
Xu Feng ◽  
Gongming Xin
Keyword(s):  
Aspect Ratio ◽  
Ultrasonic Vibration ◽  
High Aspect Ratio ◽  
Rapid Development ◽  
Glass Plate ◽  
Slit Width ◽  
Critical Voltage ◽  
Machining Parameters ◽  
Planar Coil ◽  
Helical Electrode

With the rapid development of micro-electro-mechanical systems (MEMSs), the demand for glass microstructure is increasing. For the purpose of achieving high quality and stable machining of glass microstructures with a high aspect ratio, ultrasonic vibration is applied into the micro-wire electrochemical discharge machining (WECDM), which is proposed as ultrasonic vibration-assisted WECDM with a micro helical electrode. Firstly, the formation of a gas film on the surface of the helical electrode in WECDM machining is simulated, meaning the thickness of the gas film can be reduced by adding suitable ultrasonic amplitude, thus reducing the critical voltage, then the machining localization and stability were enhanced. Then, the micro helical electrode with a diameter of 100 μm is used to carry out sets of experiments that study the influence of ultrasonic amplitude, machining voltage, duty factor, pulse frequency, and feed rate on the slit width. The experimental results show that the machining stability and quality are significantly improved by adding suitable ultrasonic amplitude. When the amplitude was 5.25 μm, the average slit width was reduced to 128.63 μm with a decrease of 20.78%. Finally, with the optimized machining parameters, micro planar coil structure and microcantilever structure with a high aspect ratio were fabricated successfully on the glass plate. It is proved that ultrasonic vibration-assisted WECDM with the micro helical electrode method can meet the requirements of high aspect ratio microstructure machining for hard and brittle materials.

scholarly journals An Investigation of the High-Frequency Ultrasonic Vibration-Assisted Cutting of Steel Optical Moulds

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 460
Author(s):  
Canbin Zhang ◽  
Chifai Cheung ◽  
Benjamin Bulla ◽  
Chenyang Zhao
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
High Frequency ◽  
Optical Glass ◽  
Contact Point ◽  
Cutting Speed ◽  
Optical Quality ◽  
Machining Parameters ◽  
Nose Radius ◽  
Cutting Geometry

Ultrasonic vibration-assisted cutting (UVAC) has been regarded as a promising technology to machine difficult-to-machine materials such as tungsten carbide, optical glass, and hardened steel in order to achieve superfinished surfaces. To increase vibration stability to achieve optical surface quality of a workpiece, a high-frequency ultrasonic vibration-assisted cutting system with a vibration frequency of about 104 kHz is used to machine spherical optical steel moulds. A series of experiments are conducted to investigate the effect of machining parameters on the surface roughness of the workpiece including nominal cutting speed, feed rate, tool nose radius, vibration amplitude, and cutting geometry. This research takes into account the effects of the constantly changing contact point on the tool edge with the workpiece induced by the cutting geometry when machining a spherical steel mould. The surface morphology and surface roughness at different regions on the machined mould, with slope degrees (SDs) of 0°, 5°, 10°, and 15°, were measured and analysed. The experimental results show that the arithmetic roughness Sa of the workpiece increases gradually with increasing slope degree. By using optimised cutting parameters, a constant surface roughness Sa of 3 nm to 4 nm at different slope degrees was achieved by the applied high-frequency UVAC technique. This study provides guidance for ultra-precision machining of steel moulds with great variation in slope degree in the pursuit of optical quality on the whole surface.

Experimental Research on Surface Roughness of Ultrasonic Assisted Grinding on 7075 Aluminum Alloy

2021 ◽  
Vol 1047 ◽  
pp. 62-67
Author(s):  
Shen Wang ◽  
Le Tong ◽  
Guang Jun Chen ◽  
Mao Xun Wang ◽  
Bin Dai ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Processing Parameters ◽  
7075 Aluminum Alloy ◽  
Machined Surface ◽  
Ultrasonic Assisted Grinding ◽  
Great Performance ◽  
Ultrasonic Assisted ◽  
Conventional Grinding ◽  
Micro Morphology

7075 aluminum alloy is widely used due to its great performance, especially in aerospace area. In this paper, ultrasonic-assisted grinding technology is used to process 7075 aluminum alloy. The data is obtained through experiments, and the surface roughness and morphology of ultrasonic assisted grinding and conventional grinding under different spindle speeds, feed rates, and amplitudes are analyzed. Research has found that the increase in spindle speed and amplitude will improve the quality of the machined surface and reduce the surface roughness by 82.1% and 36%. However, with the increase of feed rate, the surface quality decreased significantly, and the surface roughness increased by 55.6%. The surface micro-morphology of the machined workpiece is observed, and the effects of different processing parameters on the surface micro-morphology are obtained.

Sign in / Sign up

Export Citation Format

Share Document