scholarly journals Recovery of Ultra-Fine Tungsten and Tin from Slimes Using Large-Scale SLon-2400 Centrifugal Separator

Minerals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 694
Author(s):  
Tao Xiong ◽  
Xiangjun Ren ◽  
Meifang Xie ◽  
Yuhuan Rao ◽  
Yongjun Peng ◽  
...  
Keyword(s):  
Large Scale ◽  
Operating Conditions ◽  
Heavy Minerals ◽  
Separation Performance ◽  
Centrifugal Separator ◽  
High Recovery ◽  
Heavy Particles ◽  
High Efficient ◽  
Fine Tungsten ◽  
Efficient Recovery

China is very rich in tungsten and tin resources, but most of them are finely disseminated with gangues, and thus, fine grinding is required for effective separation, which results in the abundant production of ultra-fine tungsten and tin values into slimes and tailings. The SLon centrifugal separator is highly effective in recovering ultra-fine heavy particles, because it operates on the centrifugal acceleration of particles in the flowing film of a few millimeters thick. The recovery of ultra-fine tungsten minerals from a slime assaying 0.22% WO3, in which 81.85% distributed in −40 µm fraction, was investigated using large-scale SLon-2400 centrifugal separator. Under optimized operating conditions, it produced a primary tungsten concentrate assaying 1.65% WO3 at a high recovery of 77.83%. Moreover, it produced a primary tin concentrate assaying 1.56% Sn at a high recovery of 79.85% from a tin slime assaying 0.27% Sn, in which 74.78% Sn was distributed in −40 µm fraction; then, followed by the flotation cleaning process, a final tin concentrate assaying 16.23% Sn with 66.7% recovery was produced. It was particularly noted that in this large-scale centrifugal separator, the three-conical separation drum stuck with abrasion-resistant ceramic slices on its inner surface played a key role for achieving high constant separation performance. It was concluded that the SLon centrifugal separator has important application prospects for high-efficient recovery of ultra-fine heavy minerals from slimes and tailings.

Multiphase CFD Model Development for a Rotating Centrifugal Separator

2012 ◽  
Author(s):  
Daniel DeMore ◽  
William Maier
Keyword(s):  
Separation Efficiency ◽  
Fluid Dynamic ◽  
Model Development ◽  
Modeling Method ◽  
Operating Conditions ◽  
Cfd Modeling ◽  
Separation Performance ◽  
Centrifugal Separator ◽  
Wide Range ◽  
The Impact

The present paper describes the development of a Computational Fluid Dynamic (CFD) modeling approach suitable for the analysis, design, and optimization of rotating centrifugal separator stage geometries. The Homogeneous Multiple Size Group (MUSIG) model implemented in the commercial code CFX V13.0 was utilized as a basis for the CFD modeling method. The model was developed through a series of studies to understand the impact of droplet size distribution, particle coalescence, rotor/stator interface treatment, and mesh resolution on the prediction of separation efficiency for a given rotating separator geometry. This model was then validated against the OEM’s extensive in-house experimental separation testing database. The resulting CFD modeling method is shown to adequately reproduce observed trends in separation performance over a wide range of operating conditions.

Adsorption Isotherm Predictions for Multiple Molecules in MOFs Using the Same Deep Learning Model

2019 ◽  
Author(s):  
Ryther Anderson ◽  
Achay Biong ◽  
Diego Gómez-Gualdrón
Keyword(s):  
Neural Network ◽  
Machine Learning ◽  
Molecular Simulation ◽  
Large Scale ◽  
Learning Model ◽  
Operating Conditions ◽  
Small Subset ◽  
Screening Methods ◽  
Large Set ◽  
Metal Organic

<div>Tailoring the structure and chemistry of metal-organic frameworks (MOFs) enables the manipulation of their adsorption properties to suit specific energy and environmental applications. As there are millions of possible MOFs (with tens of thousands already synthesized), molecular simulation, such as grand canonical Monte Carlo (GCMC), has frequently been used to rapidly evaluate the adsorption performance of a large set of MOFs. This allows subsequent experiments to focus only on a small subset of the most promising MOFs. In many instances, however, even molecular simulation becomes prohibitively time consuming, underscoring the need for alternative screening methods, such as machine learning, to precede molecular simulation efforts. In this study, as a proof of concept, we trained a neural network as the first example of a machine learning model capable of predicting full adsorption isotherms of different molecules not included in the training of the model. To achieve this, we trained our neural network only on alchemical species, represented only by their geometry and force field parameters, and used this neural network to predict the loadings of real adsorbates. We focused on predicting room temperature adsorption of small (one- and two-atom) molecules relevant to chemical separations. Namely, argon, krypton, xenon, methane, ethane, and nitrogen. However, we also observed surprisingly promising predictions for more complex molecules, whose properties are outside the range spanned by the alchemical adsorbates. Prediction accuracies suitable for large-scale screening were achieved using simple MOF (e.g. geometric properties and chemical moieties), and adsorbate (e.g. forcefield parameters and geometry) descriptors. Our results illustrate a new philosophy of training that opens the path towards development of machine learning models that can predict the adsorption loading of any new adsorbate at any new operating conditions in any new MOF.</div>

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1992 ◽  
Vol 114 (4) ◽  
pp. 847-857 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Comparison of the efficiency of large-scale ceramic and membrane aeration systems with the dynamic off-gas method

2002 ◽  
Vol 46 (4-5) ◽  
pp. 317-324 ◽  
Author(s):  
J.A. Libra ◽  
A. Schuchardt ◽  
C. Sahlmann ◽  
J. Handschag ◽  
U. Wiesmann ◽  
...  
Keyword(s):  
Large Scale ◽  
Operating Conditions ◽  
Air Distribution ◽  
Energy Costs ◽  
Dissolved Oxygen Concentration ◽  
Membrane Aeration ◽  
Aeration System ◽  
Oxygen Transfer Efficiency ◽  
Aeration Efficiency ◽  
Period Measurement

The aeration systems of two full-scale activated sludge basins were compared over 2.5 years under the same operating conditions using dynamic off-gas testing. Only the material of the diffuser was different, membrane vs. ceramic tube diffusers. The experimental design took the complexity and dynamics of the system into consideration. The investigation has shown that, although the membrane diffusers have higher initial standard oxygen transfer efficiency (SOTE) and standard aeration efficiency (SAE), these decreased over time, while the SAE of the ceramic diffusers started lower, but increased slightly over the whole period. Measurement of air distribution in the basins along with dissolved oxygen concentration profiles have provided important information on improving process control and reducing energy costs. The results show that dynamic off-gas testing can effectively be used for monitoring the aeration system and to check design assumptions under operating conditions. The information can be used to improve the design of new aeration systems or in retro-fitting existing basins.

scholarly journals Hardware-in-the-loop simulation of wave energy converters based on dielectric elastomer generators

Meccanica ◽  
2021 ◽  
Vol 56 (5) ◽  
pp. 1223-1237
Author(s):  
Giacomo Moretti ◽  
Andrea Scialò ◽  
Giovanni Malara ◽  
Giovanni Gerardo Muscolo ◽  
Felice Arena ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Scale ◽  
Low Cost ◽  
Test Site ◽  
Dielectric Elastomer ◽  
Operating Conditions ◽  
Polymer Materials ◽  
Hardware In The Loop ◽  
Wave Energy Converters ◽  
Energy Converters

AbstractDielectric elastomer generators (DEGs) are soft electrostatic generators based on low-cost electroactive polymer materials. These devices have attracted the attention of the marine energy community as a promising solution to implement economically viable wave energy converters (WECs). This paper introduces a hardware-in-the-loop (HIL) simulation framework for a class of WECs that combines the concept of the oscillating water columns (OWCs) with the DEGs. The proposed HIL system replicates in a laboratory environment the realistic operating conditions of an OWC/DEG plant, while drastically reducing the experimental burden compared to wave tank or sea tests. The HIL simulator is driven by a closed-loop real-time hydrodynamic model that is based on a novel coupling criterion which allows rendering a realistic dynamic response for a diversity of scenarios, including large scale DEG plants, whose dimensions and topologies are largely different from those available in the HIL setup. A case study is also introduced, which simulates the application of DEGs on an OWC plant installed in a mild real sea laboratory test-site. Comparisons with available real sea-test data demonstrated the ability of the HIL setup to effectively replicate a realistic operating scenario. The insights gathered on the promising performance of the analysed OWC/DEG systems pave the way to pursue further sea trials in the future.

Experimental Study on the Behavior of a Swimming Pool Onboard a Large Passenger Ship

2009 ◽  
Vol 46 (01) ◽  
pp. 27-33
Author(s):  
Pekka Ruponen ◽  
Jerzy Matusiak ◽  
Janne Luukkonen ◽  
Mikko Ilus
Keyword(s):  
Large Scale ◽  
Hydraulic Cylinder ◽  
Operating Conditions ◽  
Swimming Pool ◽  
Scale Model ◽  
Longitudinal Motion ◽  
Sea State ◽  
Passenger Ship ◽  
Large Scale Model ◽  
Computer Controlled

The water in a swimming pool on the top deck of a large passenger ship can be excited to a resonant motion, even in a moderate sea state. The motion of the water in the pool is mainly caused by longitudinal acceleration, resulting from the ship's pitch and surge motions. At resonance, there can be high waves in the pool and splashing of water. In this study the behavior of the Solarium Pool of the Freedom of the Seas was examined in various sea states and operating conditions. The motions of the pool were calculated on the basis of a linear seakeeping method, and the behavior of the water in the pool was studied with experimental model tests. A large-scale model of the pool was constructed and fitted to a purpose-built test bench that could be axially moved by a computer-controlled hydraulic cylinder. Water elevation in the pool was measured, and all tests were video recorded. Different modifications of the pool were tested to improve the behavior of the pool. A strong correlation between the longitudinal motion and the behavior of the water in the pool was found.

Experimental Results of a PEM System Operated on Hydrogen and Reformate

2008 ◽  
Vol 5 (1) ◽  
Author(s):  
M. Minutillo ◽  
E. Jannelli ◽  
F. Tunzio
Keyword(s):  
Fuel Cell ◽  
Natural Gas ◽  
Large Scale ◽  
Pem Fuel Cell ◽  
Proton Exchange ◽  
Operating Conditions ◽  
Cell Performance ◽  
Pure Hydrogen ◽  
Test Bed ◽  
Fuel Cell Performance

The main objective of this study is to evaluate the performance of a proton exchange membrane (PEM) fuel cell generator operating for residential applications. The fuel cell performance has been evaluated using the test bed of the University of Cassino. The experimental activity has been focused to evaluate the performance in different operating conditions: stack temperature, feeding mode, and fuel composition. In order to use PEM fuel cell technology on a large scale, for an electric power distributed generation, it could be necessary to feed fuel cells with conventional fuel, such as natural gas, to generate hydrogen in situ because currently the infrastructure for the distribution of hydrogen is almost nonexistent. Therefore, the fuel cell performance has been evaluated both using pure hydrogen and reformate gas produced by a natural gas reforming system.

Evaluation of Fuel Preparation Systems for Lean Premixing-Prevaporizing Combustors

1986 ◽  
Vol 108 (2) ◽  
pp. 391-395
Author(s):  
W. J. Dodds ◽  
E. E. Ekstedt
Keyword(s):  
System Design ◽  
Large Scale ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Fuel Injectors ◽  
Design Concepts ◽  
Mixture Preparation ◽  
Design Variables ◽  
System Length

A series of tests was conducted to provide data for the design of premixing-prevaporizing fuel-air mixture preparation systems for aircraft gas turbine engine combustors. Fifteen configurations of four different fuel-air mixture preparation system design concepts were evaluated to determine fuel-air mixture uniformity at the system exit over a range of conditions representative of cruise operation for a modern commercial turbofan engine. Operating conditions, including pressure, temperature, fuel-air ratio, and velocity had no clear effect on mixture uniformity in systems which used low-pressure fuel injectors. However, performance of systems using pressure atomizing fuel nozzles and large-scale mixing devices was shown to be sensitive to operating conditions. Variations in system design variables were also evaluated and correlated. Mixture uniformity improved with increased system length, pressure drop, and number of fuel injection points per unit area. A premixing system compatible with the combustor envelope of a typical combustion system and capable of providing mixture nonuniformity (standard deviation/mean) below 15% over a typical range of cruise operating conditions was demonstrated.

scholarly journals Design and Analysis of High-Efficient Driver Model for LED Luminaires

2021 ◽  
pp. 96-106
Author(s):  
Onur Akalp ◽  
Harun Ozbay ◽  
Serhat Berat Efe
Keyword(s):  
Energy Efficient ◽  
Supply System ◽  
Operating Conditions ◽  
Driver Model ◽  
Zero Voltage Switching ◽  
Proposed Model ◽  
High Efficient ◽  
Driver Circuit ◽  
Low Volume ◽  
Zero Voltage

LED luminaires need a driver circuit for working properly. Most of the drivers have disadvantages such as losses during operation. This issue becomes more important while supplying with limited sources such as renewables. To overcome the problem, this study proposes a novel energy efficient driver for LED luminaires based on zero voltage switching (ZVS) single-ended primary inductance converter (SEPIC) technology. Driver and hence luminaires were designed to be fed from photovoltaic (PV) panels. In addition, an adaptive MPPT algorithm was developed to obtain optimum efficiency from supply system. SEPIC approach was preferred for MPPT application due to its advantages such as non-reversing polarity. This feature allows energy efficiency in corporation with ZVS. Proposed model was designed under PSIM platform with all components; PV panels, ZVS, SEPIC, and LED luminaires. A detailed analysis was performed by using system graphs under various operating conditions as different irradiance levels. Results show that proposed model is energy efficient and modular because of its low-volume structure. Therefore the model can lead smaller driver circuits with minimum losses.

scholarly journals HEAVY CLASTIC MINERALS AS AN INDICATOR OF GEODYNAMIC SETTINGS OF ACCUMULATION AND PROVENANCE OF CRETACEOUS SEDIMENTS OF THE WEST SAKHALIN TERRANE

2021 ◽  
pp. 68-86
Author(s):  
A.I. Malinovsky ◽  
Keyword(s):  
Large Scale ◽  
Volcanic Rocks ◽  
Source Area ◽  
Heavy Minerals ◽  
Clastic Material ◽  
The West ◽  
Geodynamic Settings ◽  
Eurasian Continent ◽  
Ocean Boundary ◽  
By Products

The article discusses the results of studying heavy clastic minerals from the Cretaceous sandy rocks of the West Sakhalin Terrane, and also presents their paleogeodynamic interpretation. It is shown that in terms of mineralogical and petrographic parameters, the terrane sandstones correspond to typical graywackes and are petrogenic rocks formed mainly by destruction of igneous rocks of the source areas. The sediments were found to contain both sialic, granite-metamorphic association minerals, and femic, formed by products of the destruction of basic and ultrabasic volcanic rocks. The interpretation of the entire set of data on the content, distribution and microchemical composition of heavy minerals was carried out by comparing them with minerals from older rocks and modern sediments accumulated in known geodynamic settings. The results obtained indicate that during the Cretaceous, sedimentation occurred along the continent-ocean boundary in a basin associated with large-scale left-lateral transform movements of the Izanagi Plate relative to the Eurasian continent. The source area that supplied clastic material to that basin combined a sialic landmass composed of granite-metamorphic and sedimentary rocks, a mature deeply dissected ensialic island arc, and fragments of accretion prisms, in the structure of which involved ophiolites.

Sign in / Sign up

Export Citation Format

Share Document