scholarly journals Determination of Mechanical Properties of Altered Dacite by Laboratory Methods

Minerals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 813
Author(s):  
Veljko Rupar ◽  
Vladimir Čebašek ◽  
Vladimir Milisavljević ◽  
Dejan Stevanović ◽  
Nikola Živanović
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Rock Mass ◽  
Uniaxial Compressive Strength ◽  
Rock Material ◽  
Strength Parameter ◽  
Gradual Transition ◽  
Strength Parameters ◽  
Triaxial Compressive Strength ◽  
Heterogeneous Rock

This paper presents a methodology for determining the uniaxial and triaxial compressive strength of heterogeneous material composed of dacite (D) and altered dacite (AD). A zone of gradual transition from altered dacite to dacite was observed in the rock mass. The mechanical properties of the rock material in that zone were determined by laboratory tests of composite samples that consisted of rock material discs. However, the functional dependence on the strength parameter alteration of the rock material (UCS, intact UCS of the rock material, and mi) with an increase in the participation of “weaker” rock material was determined based on the test results of uniaxial and triaxial compressive strength. The participation of altered dacite directly affects the mode and mechanism of failure during testing. Uniaxial compressive strength (σciUCS) and intact uniaxial compressive strength (σciTX) decrease exponentially with increased AD volumetric participation. The critical ratio at which the uniaxial compressive strength of the composite sample equals the strength of the uniform AD sample was at a percentage of 30% AD. Comparison of the obtained exponential equation with practical suggestions shows a good correspondence. The suggested methodology for determining heterogeneous rock mass strength parameters allows us to determine the influence of rock material heterogeneity on the values σciUCS, σciTX, and constant mi. Obtained σciTX and constant mi dependences define more reliable rock material strength parameter values, which can be used, along with rock mass classification systems, as a basis for assessing rock mass parameters. Therefore, it is possible to predict the strength parameters of the heterogeneous rock mass at the transition of hard (D) and weak rock (AD) based on all calculated strength parameters for different participation of AD.

Mineralization Influence on the Strength Parameter of Solid Wood

2015 ◽  
Vol 1122 ◽  
pp. 15-18
Author(s):  
Tereza Murínová ◽  
Pavel Mec ◽  
Jana Daňková ◽  
Petr Rezek
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Compressive Strength ◽  
Liquid Water ◽  
Solid Wood ◽  
Strength Parameter ◽  
Strength Parameters ◽  
Mineral Particles

Moisture characteristics, related durability and especially strength parameters are observed for wood (solid, treated, or modified), which is used in building constructions. Material modification by siliceous substances reduces intake of liquid water, but solution exposition and subsequent deposition of mineral particles may also affect the physico - mechanical properties of the material. In this work, longitudinal compressive strength was determined for the samples treated by dipping in aqueous solution of organosilane. The results confirm the correlation between the length of dipping and the change of tested strength parameter.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Material-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)

2021 ◽  
Vol 28 (1) ◽  
pp. 343-351
Author(s):  
Norbert Kępczak ◽  
Radosław Rosik ◽  
Mariusz Urbaniak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Young’S Modulus ◽  
Industrial Waste ◽  
Splitting Tensile Strength ◽  
Polymer Concrete ◽  
Strength Parameters ◽  
Basic Parameters ◽  
Natural Fillers

Abstract The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.

Comparative experimental study on physical and mechanical properties of quartz sandstone after water-cooling and natural-cooling under high temperature

2021 ◽  
pp. qjegh2020-181
Author(s):  
Haopeng Jiang ◽  
Annan Jiang ◽  
Fengrui Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Heating Temperature ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Water Cooling ◽  
Average Value ◽  
Cooling Methods

Experimental tests were conducted to study the influence of natural cooling and water cooling on the physical and mechanical properties of quartz sandstone. This study aims to understand the effect of different cooling methods on the physical and mechanical properties of quartz sandstone (such as mass, volume, density, P-wave velocity, elastic modulus, uniaxial compressive strength, etc.). The results show that the uniaxial compressive strength (UCS) and elastic modulus(E) of the specimens cooled by natural-cooling and water-cooling decrease with heating temperature. At 800℃, after natural cooling and water cooling, the average value of UCS decreased by 34.65% and 57.90%, and the average value of E decreased by 87.66% and 89.05%, respectively. Meanwhile, scanning electron microscope (SEM) images were used to capture the development of microcracks and pores within the specimens after natural-cooling and water-cooling, and it was found that at the same temperature, water cooling treatment was more likely to cause microcracks and pores, which can cause more serious damage to the quartz sandstone. These results confirm that different cooling methods have different effects on the physical and mechanical properties of quartz sandstone, and provide a basis for the stability prediction of rock mass engineering such as tunnel suffering from fire.

scholarly journals Strength and abrasive properties of andesite: relationships between strength parameters measured on cylindrical test specimens and micro-Deval values—a tool for durability assessment

2020 ◽  
Author(s):  
Balázs Czinder ◽  
Ákos Török
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Test Results ◽  
Strength Parameters ◽  
Data Set ◽  
Freeze Thaw ◽  
Laboratory Test Results ◽  
Significant Difference ◽  
Abrasive Properties ◽  
Water Saturated

Abstract Aggregates are necessary materials for the construction industry. Owing to their favourable properties, andesites are frequently used rock materials; hence, the investigation of their mechanical and aggregate properties has great significance. This paper introduces the analyses of 13 Hungarian andesite lithotypes. The samples were collected from six andesite quarries in Hungary. Cylindrical specimens and aggregate samples with 10.0/14.0-mm-sized grains were made from rock blocks. The specimens were tested in dry, water-saturated and freeze–thaw subjected conditions. Bulk density, uniaxial compressive strength, modulus of elasticity, indirect tensile strength and water absorption were measured. The abrasion resistance was tested by micro-Deval tests. The flakiness indexes of the samples were also measured. The data set of the laboratory test results provided input for further, one- and two-variable statistical analyses. According to the test results, there is no significant difference between the strength parameters measured in water-saturated and in freeze–thaw subjected conditions. The correlation and regression analyses revealed relationships between some rock mechanical parameters, as well as between micro-Deval coefficient and uniaxial compressive strength.

EFFECT OF PETROLOGICAL FEATURES ON MECHANICAL PROPERTIES OF ROCK SALT FROM THE LGOM (LEGNICA–GŁOGÓW COPPER DISTRICT)

2016 ◽  
pp. 51-64 ◽  
Author(s):  
Katarzyna CYRAN ◽  
Tomasz TOBOŁA ◽  
Paweł KAMIŃSKI
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Rock Salt ◽  
Fluid Inclusions ◽  
Mechanical Parameters ◽  
Research Results ◽  
Strength Tests ◽  
Crystal Boundaries

The paper presents the attempt to find a correlation between the content of impurities and mechanical parameters of rock salt from the LGOM. Research was carried out in three steps: uniaxial compressive strength tests, determination of the content of insoluble minerals (impurities), and observations under the microscope and Raman microspectroscopy. The research results reveal that the rock salt which is characterized by low content of insoluble minerals (0.13–2.11% wt.) shows no correlation between the mechanical properties and the content of impurities. However, it was found that mechanical properties depend on both the distribution of impurities in halite crystals and the presence of fluid inclusions and hydrocarbons along the crystal boundaries. Moreover, the distribution of anhydrite at the edges of halite crystals may influence an increase of rock salt strength. On the contrary, the presence of fluid inclusions and hydrocarbons along the halite crystal boundaries may reduce the rock salt strength.

Classification of Engineering Properties of Tropical Boulder in Completely Weathered Granite in Johor, Malaysia

2020 ◽  
Vol 17 (2) ◽  
pp. 1059-1069
Author(s):  
Mohd Firdaus Md Dan ◽  
Edy Tonnizam Mohamad ◽  
Ibrahim Komoo ◽  
Aziman Madun ◽  
Siti Norsalkini Mohd Akip Tan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Point Load ◽  
Engineering Properties ◽  
Dry Density ◽  
Petrographic Analysis ◽  
Point Load Strength ◽  
Weathered Granite ◽  
Completely Weathered Granite

Engineering properties of tropical weathered granite mass have been widely investigated and classified for engineering purposes. However, the engineering properties of tropical boulder in weathered granite profile is poorly understood and not well classified. This study aims to examine and classify the physico-mechanical properties of granite boulder in completely weathered zone. A total of 34 in-situ boulders were examined from two granite quarries located in Southern Johor, Malaysia. Microstructure-mineralogical alterations were analyzed based on petrographic analysis and scanning electron microscopy (SEM). The mechanical properties were including dry density, porosity, point load strength, uniaxial compressive strength and permeability. Three properties were identified as significant indicators to differentiate between tropical boulder and completely weathered granite when it is evaluated from the soil investigation drilling work namely; texture characteristics, discolourations and degree of weathering. Analysis revealed that the alteration of microstructures and minerals such as feldspar, biotite, and plagioclase from corestone (Grade I/II) to saprolite (Grade IV/V) zone were significantly reduced the dry density, point load strength, uniaxial compressive strength and permeability with 32%, 99.5%, 98.6% and 84.8%, respectively. It has also significantly increased the porosity up to 11.6 times or 1065% from corestone to saprolite. The significant different of physico-mechanical properties of material surrounding boulder due to weathering can be classified and useful in evaluation of geotechnical design and geological engineering applications.

Effect of Rock Properties on Excavation-Loading Operation in Selected Quarries

2013 ◽  
Vol 824 ◽  
pp. 86-90 ◽  
Author(s):  
B. Adebayo ◽  
A.E. Aladejare
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Strong Relationship ◽  
Strength Properties ◽  
Biotite Granite ◽  
Point Load ◽  
Rock Properties ◽  
Filling Rate ◽  
Strength Parameters ◽  
Point Load Strength

The effect of rock properties on excavation-loading operation in quarries was investigated by conducting test on the mechanical properties of selected rocks. These rock samples were tested in the laboratory for specific gravity, point load strength, uniaxial compressive strength and mineral composition using weigh balance, point load tester, 1100kN compression machine and petrological microscope respectively. The filling rates of the front end loaders bucket were determined. The result obtained show that value of uniaxial compressive strength varied from 29.22 MPa-30.87 MPa. The bucket filling rate varied from 0.180-0.250 m3/s and 0.145-0.170 m3/s for porphyritic biotite granite and coarse biotite granite respectively. There is strong relationship between bucket filling rate and strength properties with values of R2 ranging from 0.9737 to 0.9981.Therefore strength parameters of the rock have effect on excavation loading operation in quarries.

Evaluation of physical and mechanical properties of rock for drilling condition classification

2013 ◽  
Vol 10 (4) ◽  
pp. 359-366 ◽  
Author(s):  
B. Adebayo ◽  
B. Adetula
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Physical And Mechanical Properties ◽  
Point System ◽  
Drilling Rate ◽  
Quartz Content ◽  
Drilling Condition ◽  
Drilling Rate Index

This work deals with the investigation of physical and mechanical properties of selected rocks for condition of drilling categorization. Rock samples collected from five drilling locations were tested in the laboratory for uniaxial compressive strength, tensile strength, and Drilling Rate Index (DRI) using 1,100 kN compression machine, point load tester and miniature drill. Similarly, hardness, brittleness, Rock Abrasivity Index (RAI), penetration rate and bit wear rate were determined. The results showed that uniaxial compressive strength, tensile strength and Drilling Rate Index varied from 47.78 - 111.11 MPa, 8.09 - 19.44 MPa, and 20 - 52 respectively. The Nast point system chart was used to classify the rocks into drilling conditions. The drilling classification shows that the drilling condition of the rocks varied from slow to fast. The drillability characteristics of the rocks vary from extremely low to medium as specified by the Drilling rate Index (DRI). It was concluded that uniaxial compressive strength, texture and grain size, drilling rate index and Equivalent Quartz Content (EQC) are important parameters affecting drilling condition of the rocks.

Sign in / Sign up

Export Citation Format

Share Document