scholarly journals Organic-Inorganic Hybrid Materials for Room Temperature Light-Activated Sub-ppm NO Detection

Nanomaterials ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 70 ◽  
Author(s):  
Abulkosim Nasriddinov ◽  
Marina Rumyantseva ◽  
Tatyana Shatalova ◽  
Sergey Tokarev ◽  
Polina Yaltseva ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Room Temperature ◽  
Single Point ◽  
Environmental Pollutants ◽  
Chemical Precipitation ◽  
Drift Spectroscopy ◽  
Semiconductor Oxides ◽  
Vis Spectroscopy ◽  
Homo And Lumo ◽  
Nanocrystalline Oxides

Nitric oxide (NO) is one of the main environmental pollutants and one of the biomarkers noninvasive diagnosis of respiratory diseases. Organic-inorganic hybrids based on heterocyclic Ru (II) complex and nanocrystalline semiconductor oxides SnO2 and In2O3 were studied as sensitive materials for NO detection at room temperature under periodic blue light (λmax = 470 nm) illumination. The semiconductor matrixes were obtained by chemical precipitation with subsequent thermal annealing and characterized by XRD, Raman spectroscopy, and single-point BET methods. The heterocyclic Ru (II) complex was synthesized for the first time and characterized by 1H NMR, 13C NMR, MALDI-TOF mass spectrometry and elemental analysis. The HOMO and LUMO energies of the Ru (II) complex are calculated from cyclic voltammetry data. The thermal stability of hybrids was investigated by thermogravimetric analysis (TGA)-MS analysis. The optical properties of Ru (II) complex, nanocrystalline oxides and hybrids were studied by UV-Vis spectroscopy in transmission and diffuse reflectance modes. DRIFT spectroscopy was performed to investigate the interaction between NO and the surface of the synthesized materials. Sensor measurements demonstrate that hybrid materials are able to detect NO at room temperature in the concentration range of 0.25–4.0 ppm with the detection limit of 69–88 ppb.

scholarly journals Photosensitive Organic-Inorganic Hybrid Materials for Room Temperature Gas Sensor Applications

Nanomaterials ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 671 ◽  
Author(s):  
Marina Rumyantseva ◽  
Abulkosim Nasriddinov ◽  
Svetlana Vladimirova ◽  
Sergey Tokarev ◽  
Olga Fedorova ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Room Temperature ◽  
Single Point ◽  
Red Light ◽  
Chemical Precipitation ◽  
Sensor Applications ◽  
Semiconductor Oxides ◽  
Ms Analysis ◽  
Vis Spectroscopy ◽  
Homo And Lumo

In this work, the hybrids based on nanocrystalline SnO2 or In2O3 semiconductor matrixes and heterocyclic Ru(II) complex are studied as materials for gas sensors operating at room temperature under photoactivation with visible light. Nanocrystalline semiconductor oxides are obtained by chemical precipitation with subsequent thermal annealing and characterized by XRD, SEM and single-point BET methods. The heterocyclic Ru(II) complex is synthesized for the first time and investigated by 1H NMR, 13C NMR APT, MALDI-MS analysis, and UV-Vis spectroscopy. The HOMO and LUMO energies of the Ru(II) complex are calculated from cyclic voltammetry data. The hybrid materials are characterized by TGA-MS analysis and EDX mapping. The optical properties of hybrids are studied by UV-Vis spectroscopy in the diffuse reflection mode. The investigation of spectral dependencies of photoconductivity of hybrid samples demonstrates that the role of organic dye consists in shifting the photosensitivity range towards longer wavelengths. Sensor measurements demonstrate that hybrid materials are able to detect NO2 in the concentration range of 0.25–2 ppm without the use of thermal heating under periodic illumination with even low-energy long-wavelength (red) light.

Seed-mediated synthesis and PEG coating of gold nanoparticles for controlling morphology and sizes

MRS Advances ◽  
2020 ◽  
Vol 5 (63) ◽  
pp. 3353-3360
Author(s):  
Susana Helena Arellano Ramírez ◽  
Perla García Casillas ◽  
Christian Chapa González
Keyword(s):  
Gold Nanoparticles ◽  
Polyethylene Glycol ◽  
Room Temperature ◽  
Colloidal Stability ◽  
Infrared Spectrometry ◽  
Ammonium Bromide ◽  
Chloroauric Acid ◽  
Vis Spectroscopy ◽  
Seed Mediated ◽  
Peg Coating

AbstractA significant area of research is biomedical applications of nanoparticles which involves efforts to control the physicochemical properties through simple and scalable processes. Gold nanoparticles have received considerable attention due to their unique properties that they exhibit based on their morphology. Gold nanospheres (AuNSs) and nanorods (AuNRs) were prepared with a seed-mediated method followed of polyethylene glycol (PEG)-coating. The seeds were prepared with 0.1 M cetyltrimethyl-ammonium bromide (CTAB), 0.005 M chloroauric acid (HAuCl4), and 0.01 M sodium borohydride (NaBH4) solution. Gold nanoparticles with spherical morphology was achieved by growth by aggregation at room temperature, while to achieve the rod morphology 0.1 M silver nitrate (AgNO3) and 0.1 M ascorbic acid solution were added. The gold nanoparticles obtained by the seed-mediated synthesis have spherical or rod shapes, depending on the experimental conditions, and a uniform particle size. Surface functionalization was developed using polyethylene glycol. Morphology, and size distribution of AuNPs were evaluated by Field Emission Scanning Electron Microscopy. The average size of AuNSs, and AuNRs was 7.85nm and 7.96 x 31.47nm respectively. Fourier transform infrared spectrometry was performed to corroborate the presence of PEG in the AuNPs surface. Additionally, suspensions of AuNSs and AuNRs were evaluated by UV-Vis spectroscopy. Gold nanoparticles were stored for several days at room temperature and it was observed that the colloidal stability increased once gold nanoparticles were coated with PEG due to the shield formed in the surface of the NPs and the increase in size which were 9.65±1.90 nm of diameter for AuNSs and for AuNRs were 29.03±5.88 and 8.39±1.02 nm for length and transverse axis, respectively.

Green synthesis of mixed metallic nanoparticles using room temperature self-assembly

2017 ◽  
Vol 13 (2) ◽  
pp. 4671-4677 ◽  
Author(s):  
A. M. Abdelghany ◽  
A.H. Oraby ◽  
Awatif A Hindi ◽  
Doaa M El-Nagar ◽  
Fathia S Alhakami
Keyword(s):  
Self Assembly ◽  
Metallic Nanoparticles ◽  
Room Temperature ◽  
Bimetallic Nanoparticles ◽  
Reduction Process ◽  
Nano Particles ◽  
Nano Structure ◽  
Small Shift ◽  
Molar Ratios ◽  
Vis Spectroscopy

Bimetallic nanoparticles of silver (Ag) and gold (Au) were synthesized at room temperature using Curcumin. Reduction process of silver and gold ions with different molar ratios leads to production of different nanostructures including alloys and core-shells. Produced nanoparticles were characterized simultaneously with FTIR, UV/vis. spectroscopy, transmission electron microscopy (TEM), and Energy-dispersive X-ray (EDAX). UV/vis. optical absorption spectra of as synthesized nanoparticles reveals presence of surface palsmon resonance (SPR) of both silver at (425 nm) and gold at (540 nm) with small shift and broadness of gold band after mixing with resucing and capping agent in natural extract which suggest presence of bimetallic nano structure (Au/Ag). FTIR and EDAX data approve the presence of bimetallic nano structure combined with curcumin extract. TEM micrographs shows that silver and gold can be synthesized separately in the form of nano particles using curcumin extract. Synthesis of gold nano particles in presence of silver effectively enhance and control formation of bi-metallic structure.

scholarly journals Preparation and Gas Sensing Properties of PANI/SnO2 Hybrid Material

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1360
Author(s):  
Qiaohua Feng ◽  
Huanhuan Zhang ◽  
Yunbo Shi ◽  
Xiaoyu Yu ◽  
Guangdong Lan
Keyword(s):  
Hybrid Material ◽  
Room Temperature ◽  
Tin Dioxide ◽  
Gas Adsorption ◽  
Gas Sensing ◽  
Oxidative Polymerization ◽  
Environmental Pollutants ◽  
Decomposition Temperature ◽  
Benzene Vapor ◽  
Thermo Gravimetric Analyzer

A sensor operating at room temperature has low power consumption and is beneficial for the detection of environmental pollutants such as ammonia and benzene vapor. In this study, polyaniline (PANI) is made from aniline under acidic conditions by chemical oxidative polymerization and doped with tin dioxide (SnO2) at a specific percentage. The PANI/SnO2 hybrid material obtained is then ground at room temperature. The results of scanning electron microscopy show that the prepared powder comprises nanoscale particles and has good dispersibility, which is conducive to gas adsorption. The thermal decomposition temperature of the powder and its stability are measured using a differential thermo gravimetric analyzer. At 20 °C, the ammonia gas and benzene vapor gas sensing of the PANI/SnO2 hybrid material was tested at concentrations of between 1 and 7 ppm of ammonia and between 0.4 and 90 ppm of benzene vapor. The tests show that the response sensitivities to ammonia and benzene vapor are essentially linear. The sensing mechanisms of the PANI/SnO2 hybrid material to ammonia and benzene vapors were analyzed. The results demonstrate that doped SnO2 significantly affects the sensitivity, response time, and recovery time of the PANI material.

scholarly journals Back protection of canvas paintings

2020 ◽  
Vol 8 (1) ◽  
Author(s):  
Tim Padfield ◽  
Nicolas Padfield ◽  
Daniel Sang-Hoon Lee ◽  
Anne Thøgersen ◽  
Astrid Valbjørn Nielsen ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Relative Humidity ◽  
Temperature Variation ◽  
Room Temperature ◽  
Single Point ◽  
Confined Space ◽  
Constant Wall Temperature ◽  
Back Plate ◽  
Inner Surface

Abstract In this paper different scenarios for back protection of a canvas painting and their effect on the stability of the relative humidity behind the painting are tested. A painting on canvas, stretched on a wooden frame, was fitted with various styles of back protection and then exposed to a cycle of temperature variation at the back, with the front exposed to a constant room temperature. The painting was also exposed to a constant wall temperature and varying room temperature. The space between the canvas and the back board was fitted with temperature and relative humidity (RH) sensors. The sensors were used to provide the essential single-point data of temperature and RH at the given locations. For more comprehensive understanding of the rather confined space, further numerical simulation (computational fluid dynamics) was adopted as part of the investigation. The computational fluid dynamics was used to understand the natural convection within the microclimate through the depictions of temperature distribution, as well as the corresponding airflow. The unprotected painting suffered a large RH variation at its back, because of the varying canvas temperature interacting with the constant room air moisture content. Effective stabilisation of the RH behind the canvas against temperature variation was provided by a shiny aluminium alloy sheet sealed against the frame. The non-absorbent back board experienced a strong variation in RH, because of humidity buffering of the space by the painting canvas at a different temperature. Either a space or insulation between this back plate and the wall reduced the risk of condensation on the inner surface of the back plate. Insulation will however increase the risk of condensation on the wall surface behind the painting. An absorbent back board de-stabilised the RH at the painting canvas surface by providing a competing humidity buffer at a different temperature. To provide protection against moisture exchange with an unsuitable room RH, extra humidity buffer was placed 3 mm behind the painting canvas, kept close to the painting temperature by insulation between this buffer and the back board. This stabilised RH at the canvas surface but increased both the temperature and the RH variation at the back board and thus increased the risk of condensation on the inner surface of the back board. The RH and the temperature in the narrow spaces between the painting canvas and the wooden stretcher frame were always more nearly constant than in the open canvas area, which suggests an explanation for the widely observed better condition of the areas of canvas paintings which lie close over the support structure. Our conclusion is that a non-absorbent, impermeable back plate gives good RH stability against a changing temperature gradient between wall and canvas painting surface.

Barium calcium titanate @carbon hybrid materials for high-efficiency room-temperature pyrocatalysis

2021 ◽  
Author(s):  
Huiying Wang ◽  
Yanmin Jia ◽  
Taosheng Xu ◽  
Xiaoxin Shu ◽  
Yiming He ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Room Temperature ◽  
High Efficiency ◽  
Calcium Titanate

Inter-Pulse Spectroscopy Based on Room-Temperature Pulsed Quantum-Cascade Laser for N2O Detection

2011 ◽  
Vol 128-129 ◽  
pp. 607-610
Author(s):  
Min Wang ◽  
Jie Chen ◽  
Niu Liu ◽  
Ya Wang
Keyword(s):  
Absorption Spectrum ◽  
Room Temperature ◽  
Single Point ◽  
High Sensitivity ◽  
Fast Response ◽  
Trace Gas ◽  
High Resolution Spectrum ◽  
Light Sources ◽  
Quantum Cascade ◽  
Pulse Spectroscopy

Mid-infrared lasers are very suitable for high-sensitive trace-gases detection for their wavelengths cover the fundamental absorption lines of most gases. Quantum-cascade (QC) lasers have been demonstrated to be ideal light sources with its special power, tuning and capability of operating in room-temperature. All these merits make it appropriate for the high resolution spectrum analysis. The absorption spectrum monitoring technology based on the QC laser pulsed operating in the room temperature, combining with the strong absorption of the gas molecule in the basic frequency, has become an effective way to monitor the trace gas with the characteristic of high sensitivity, good selectivity and fast response. In this paper, the inter-pulse spectroscopy based on a room-temperature distributed-feedback pulsed QC laser was introduced. Our approach to trace gas monitoring with QC lasers relies on short current pulses which are designed to produce even shorter light pulses. Each pulse corresponds to a single point in a spectrum. The N2O absorption spectrum centered at 2178.2cm-1was also obtained.

The role of platinum on the NOx storage and desorption behavior of ceria: An online FT-IR study combined with in situ Raman and UV-Vis spectroscopy

2020 ◽  
Author(s):  
Anastasia Filtschew ◽  
Pablo Beato ◽  
Søren Birk Rasmussen ◽  
Christian Hess
Keyword(s):  
Gas Phase ◽  
Phase Analysis ◽  
Room Temperature ◽  
Storage Mechanism ◽  
In Situ Raman ◽  
Vis Spectroscopy ◽  
Ft Ir ◽  
Ir Study

The role of platinum on the room temperature NOx storage mechanism and the NOx desorption behavior of ceria was investigated by combining online FT-IR gas-phase analysis with in situ Raman...

scholarly journals Crystal Chemistry and Luminescence Properties of Eu-Doped Polycrystalline Hydroxyapatite Synthesized by Chemical Precipitation at Room Temperature

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 250 ◽  
Author(s):  
Francesco Baldassarre ◽  
Angela Altomare ◽  
Nicola Corriero ◽  
Ernesto Mesto ◽  
Maria Lacalamita ◽  
...  
Keyword(s):  
Fourier Transform ◽  
High Temperature ◽  
Inductively Coupled Plasma ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Chemical Precipitation ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled

Europium-doped hydroxyapatite Ca10(PO4)6(OH)2 (3% mol) powders were synthesized by an optimized chemical precipitation method at 25 °C, followed by drying at 120 °C and calcination at 450 °C and 900 °C. The obtained nanosized crystallite samples were investigated by means of a combination of inductively coupled plasma (ICP) spectroscopy, powder X-ray diffraction (PXRD), Fourier Transform Infrared (FTIR), Raman and photoluminescence (PL) spectroscopies. The Rietveld refinement in the hexagonal P63/m space group showed europium ordered at the Ca2 site at high temperature (900 °C), and at the Ca1 site for lower temperatures (120 °C and 450 °C). FTIR and Raman spectra showed slight band shifts and minor modifications of the (PO4) bands with increasing annealing temperature. PL spectra and decay curves revealed significant luminescence emission for the phase obtained at 900 °C and highlighted the migration of Eu from the Ca1 to Ca2 site as a result of increasing calcinating temperature.

Sign in / Sign up

Export Citation Format

Share Document