scholarly journals Development and Characterization of Liposomal Formulations Containing Phytosterols Extracted from Canola Oil Deodorizer Distillate along with Tocopherols as Food Additives

Pharmaceutics ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 185 ◽  
Author(s):  
Asmita Poudel ◽  
George Gachumi ◽  
Kishor M. Wasan ◽  
Zafer Dallal Bashi ◽  
Anas El-Aneed ◽  
...  

Phytosterols are plant sterols recommended as adjuvant therapy for hypercholesterolemia and tocopherols are well-established anti-oxidants. However, thermo-sensitivity, lipophilicity and formulation-dependent efficacy bring challenges in the development of functional foods, enriched with phytosterols and tocopherols. To address this, we developed liposomes containing brassicasterol, campesterol and β-sitosterol obtained from canola oil deodorizer distillate, along with alpha, gamma and delta tocopherol. Three approaches; thin film hydration-homogenization, thin film hydration-ultrasonication and Mozafari method were used for formulation. Validated liquid chromatographic tandem mass spectrometry (LC-MS/MS) was utilized to determine the entrapment efficiency of bioactives. Stability studies of liposomal formulations were conducted before and after pasteurization using high temperature short time (HTST) technique for a month. Vesicle size after homogenization and ultrasonication (<200 nm) was significantly lower than by Mozafari method (>200 nm). However, zeta potential (−9 to −14 mV) was comparable which was adequate for colloidal stability. Entrapment efficiencies were greater than 89% for all the phytosterols and tocopherols formulated by all three methods. Liposomes with optimum particle size and zeta potential were incorporated in model orange juice, showing adequate stability after pasteurization (72 °C for 15 s) for a month. Liposomes containing phytosterols obtained from canola waste along with tocopherols were developed and successfully applied as a food additive using model orange juice.

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Mohamed Badran ◽  
Khaled Shalaby ◽  
Abdullah Al-Omrani

This study focuses on the effect of different flexible liposomes containing sodium cholate, Tween 80, or cineol on skin deposition of carboxyfluorescein (CF). Size distribution, morphology, zeta potential, and stability of the prepared vesicles were evaluated. The influence of these systems on the skin deposition of CF utilizing rat skin as membrane model was investigated. Results showed that all of the investigated liposomes had almost spherical shapes with low polydispersity (PDI < 0.3) and particles size range from 83 to 175 nm. All liposomal formulations exhibited negative zeta potential, good drug entrapment efficiency, and stability.In vitroskin deposition data showed that flexible liposomes gave significant deposition of CF on the skin compared to conventional liposomes and drug solutions. This study revealed that flexible liposomes, containing cineole, were able to deliver higher amount of CF suggesting that the hydrophilic drugs delivery to the skin was strictly correlated to the vesicle composition.


2018 ◽  
Vol 1 (1) ◽  
pp. 10-15
Author(s):  
Sheo Datta Maurya

The objective of the present study was to investigate the effects of experimental conditions like pH, salt, temperature on the interactions of conventional liposomes. The model drug Stavudine was entrapped in the liposomes composed of Phosphotidyl Choline and cholesterol in the ratio of 200mg: 80mg and prepared by thin film hydration method. Liposomes preparation was characterized and compared for particle size, mean dispersion, entrapment efficiency, Zeta potential and the size enlargement studies were carried out in optical microscope by using Magnus.


2020 ◽  
Vol 17 (1) ◽  
pp. 172-183
Author(s):  
Nandanwadkar Shrikrishna Madhukar Hema ◽  
Mastiholimath Vinayak Shivamurthy ◽  
Pulija Karunakar

Introduction: Capsaicin (8-methy-N-vanillyl-6-nonenamide), a potential analgesic derived from Capsicum annuum (Chili peppers), widely used from ancient times for its pharmacological activities such as anti-inflammatory, anti-oxidant and analgesic and provides relief from migraine and diabetes. But for obvious reasons, capsaicin cannot be administered directly. The present work was designed with a focus to comply with mandatory requirement in various pharmacopeias to know the actual content of API present in final formulations. The formulation (TS3) consisting of 3% lipid, with 4:6 ratio of the polymer and solvent, was found to be the optimized formulation, which gave the best evaluation with regard to the particle size (97.03±2.68) nm, polydispersity index (0.20±0.00), higher zeta potential (61.28±2.06) mv, morphological studies and highest drug entrapment efficiency (68.34±4.24)%. The prepared transferosome formulation was subjected to characterization by validated HP-TLC method consisting of N-Hexane: Tert- Iso-butyl-methyl ether in ratio (5:15) v/v. Linearity was performed in the range of 50-1500 ng/spot with LOD/LOQ 50 ng and 150 ng, with regression analysis (R) of 99.91%. Recovery analysis was performed at 3 different levels at 80, 100 and 120 with an average recovery of 106.97%, respectively. Till now, no analytical method has been reported, associated with the characterization of pharmaceutical nano-forms (Capsaicin), like transferosomes. Thus, the maiden validated HP-TLC method for concurrent analysis of capsaicin as API in nano-transferosome may be employed in process quality control of formulations containing the said API. Background: The irritability and adverse effects post application, leading to inflammation and neural pain at the site of administration of newly Capsaicin API and its chemical entities and marketed formulations are usually related to poor permeability, leading to drug complex reactions in the development phases or therapeutic failure along with the quantification of the same in blood plasma. However, advancement in drug formulations with the use of polymer: alcohol ratio and modernized analytical techniques for the quantification of Pharmaceutical APIs seems to be emerging and promising for overcoming pain and related inflammatory complications by formulating the APIs in Transferosome formulation with Validated HP-TLC technique being used as an effective economic and precise tool for quantitative analysis of APIs in their respective nano-forms. Objective: The study proposes a novel standardized method development and validation of pharmaceutical nanoforms with Capsaicin as API. Method: Capsaicin Transferosomes were formulated using Ultra probe sonication by utilizing different proportions of phospholipid 90G dissolved in a mixture of ethanol and propylene glycol. The formulation was subjected to Dynamic Light Scattering (DLS) technique for nano-particle analysis followed by characterization with respect to particle size, polydispersity index, zeta potential and entrapment efficiency. The morphological study of vesicles was determined using SEM and TEM. A Validated HP-TLC method for the identification and determination of Capsaicin in transferosomes formulation was performed as per the ICH guidelines. Results: The formulation gave the best evaluation for particle size (97.03±2.68) nm, polydispersity index (0.20±0.00), higher zeta potential (61.28±2.06) mv, morphological studies (SEM & TEM) and highest drug entrapment efficiency (68.34±4.24)%. DSC thermograms and FTIR spectral patterns confirmed no physical interaction by polymers with API. The prepared formulation was then characterized using HP-TLC method. The best resolution was found in NHexane: Tert-Isobutyl methyl ether in a ratio of 5:15 v/v. The Rf was found to be 0.3±0.03. Linearity was performed in a range of 50-1500 ng/spot, with regression analysis (R) of 99.91% Further, recovery analysis was done at 3 different levels as 80, 100 and 120 with an average recovery of 106.97%. The LOD/LOQ was found to be 50 and 150 ng, respectively. Precision was carried out in which % RSD was found to be precise and accurate. Conclusion: The outcomes of the present study suggested that the proposed novel formulation analyzed by Validated planar chromatographic technique (HP-TLC) for Capsaicin quantification in nanoforms may be employed as a routine quality control method for the said API in various other formulations.


Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 42
Author(s):  
Shimrith Paul Shylendra ◽  
Wade Lonsdale ◽  
Magdalena Wajrak ◽  
Mohammad Nur-E-Alam ◽  
Kamal Alameh

In this work, a solid-state potentiometric pH sensor is designed by incorporating a thin film of Radio Frequency Magnetron Sputtered (RFMS) Titanium Nitride (TiN) working electrode and a commercial Ag|AgCl|KCl double junction reference electrode. The sensor shows a linear pH slope of −59.1 mV/pH, R2 = 0.9997, a hysteresis as low as 1.2 mV, and drift below 3.9 mV/h. In addition, the redox interference performance of TiN electrodes is compared with that of Iridium Oxide (IrO2) counterparts. Experimental results show −32 mV potential shift (E0 value) in 1 mM ascorbic acid (reducing agent) for TiN electrodes, and this is significantly lower than the −114 mV potential shift of IrO2 electrodes with sub-Nernstian sensitivity. These results are most encouraging and pave the way towards the development of miniaturized, cost-effective, and robust pH sensors for difficult matrices, such as wine and fresh orange juice.


Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 923
Author(s):  
Shadab Md ◽  
Nabil A. Alhakamy ◽  
Hibah M. Aldawsari ◽  
Mohammad Husain ◽  
Nazia Khan ◽  
...  

Plumbagin (PLM) is a phytochemical which has shown cytotoxicity against of cancer cells both in vitro and in vivo. However, the clinical application of PLM has been hindered due to poor aqueous solubility and low bioavailability. The aim of the present study was to develop, optimize and evaluate PLM-loaded glycerosome (GM) gel and compare with conventional liposome (CL) for therapeutic efficacy against skin cancer. The GM formulations were optimized by employing design expert software by 3-level 3-factor design. The prepared GMs were characterized in vitro for vesicle size, size distribution, zeta potential, vesicle deformability, drug release, skin permeation, retention, texture, antioxidant and cytotoxicity activities. The optimized formulation showed a vesicle size of 119.20 ± 15.67 nm with a polydispersity index (PDI) of 0.145 ± 0.02, the zeta potential of −27 ± 5.12 mV and entrapment efficiency of 76.42 ± 9.98%. The optimized PLM-loaded GM formulation was transformed into a pre-formed gel which was prepared using Carbopol 934 polymer. The drug diffusion fluxes of CL gel and GM-loaded gel were 23.31 ±6.0 and 79.43 ± 12.43 µg/ cm2/h, respectively. The result of texture analysis revealed the adequate hardness, cohesiveness, consistency, and viscosity of the developed GM-loaded gel compared to CL gel. The confocal images showed that glycerosomal gel has deeper skin layer penetration as compared to the control solution. GM-loaded gel treated rat skin showed significantly (p < 0.05) higher drug accumulation in the dermis, higher cytotoxicity and higher antioxidant activity as compared to CL gel and PLM suspension. Thus, findings revealed that novel GM-loaded gel could be potential carriers for therapeutic intervention in skin cancer.


Author(s):  
RISA AHDYANI ◽  
LARAS NOVITASARI ◽  
RONNY MARTIEN

Objective: The objectives of this study were to formulate and characterize nanoparticles gel of timolol maleate (TM) by ionic gelation method using chitosan (CS) and sodium alginate (SA). Methods: Optimization was carried out by factorial design using Design Expert®10.0.1 software to obtain the concentration of CS, SA, and calcium chloride (CaCl2) to produce the optimum formula of TM nanoparticles. The optimum formula was characterized for particle size, polydispersity index, entrapment efficiency, Zeta potential, and molecular structure. Hydroxy Propyl Methyl Cellulose (HPMC) K15 was incorporated into optimum formula to form nanoparticles gel of TM and carried out in vivo release study using the Franz Diffusion Cell. Results: TM nanoparticles was successfully prepared with concentration of CS, SA, and CaCl2 of 0.01 % (w/v), 0.1 % (w/v), and 0.25 % (w/v), respectively. The particle size, polydispersity index, entrapment efficiency, and Zeta potential were found to be 200.47±4.20 nm, 0.27±0.0154, 35.23±4.55 %, and-5.68±1.80 mV, respectively. The result of FTIR spectra indicated TM-loaded in the nanoparticles system. In vitro release profile of TM-loaded nanoparticles gel showed controlled release and the Korsmeyer-Peppas model was found to be the best fit for drug release kinetics. Conclusion: TM-loaded CS/SA nanoparticles gel was successfully prepared and could be considered as a promising candidate for controlled TM delivery of infantile hemangioma treatment.


Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 290
Author(s):  
Yannic Ramaye ◽  
Marta Dabrio ◽  
Gert Roebben ◽  
Vikram Kestens

Zeta potential is frequently used to examine the colloidal stability of particles and macromolecules in liquids. Recently, it has been suggested that zeta potential can also play an important role for grouping and read-across of nanoforms in a regulatory context. Although the measurement of zeta potential is well established, only little information is reported on key metrological principles such as validation and measurement uncertainties. This contribution presents the results of an in-house validation of the commonly used electrophoretic light scattering (ELS) and the relatively new particle tracking analysis (PTA) methods. The performance characteristics were assessed by analyzing silica and polystyrene reference materials. The ELS and PTA methods are robust and have particle mass working ranges of 0.003 mg/kg to 30 g/kg and 0.03 mg/kg to 1.5 mg/kg, respectively. Despite different measurement principles, both methods exhibit similar uncertainties for repeatability (2%), intermediate precision (3%) and trueness (4%). These results confirm that the developed methods can accurately measure the zeta potential of silica and polystyrene particles and can be transferred to other laboratories that analyze similar types of samples. If direct implementation is impossible, the elaborated methodologies may serve as a guide to help laboratories validating their own methods.


2021 ◽  
Vol 17 ◽  
Author(s):  
Swayamprakash Patel ◽  
Ashish Patel ◽  
Mruduka Patel ◽  
Umang Shah ◽  
Mehul Patel ◽  
...  

Background: Probe sonication and High-speed homogenizer are comparatively costly equipment to fabricate the nanoparticles. Many academic and research institutions cannot afford the procurement and maintenance of such sophisticated equipment. In the present work, a newer idea is conceptualized, which can be adopted by the underprivileged research institutions to fabricate solid lipid nanoparticles (SLN) in the absence of sophisticated equipment. The current work describes the pilot-level trials of this novel approach. This study represents the preliminary proof-of-concept trials for which the Indian patent application (3508/MUM/2015) is filed. Method: A frugal piece of equipment was made using a 50 ml centrifuge tube with conical bottom and a piezoelectric mist maker or humidifier. SLNs were prepared by combining the quasi-emulsion solvent evaporation approach and ultrasonic vibration approach. A quasi-emulsion was composed by the dropwise mixing of the organic solvent containing drug & lipid with an aqueous solution containing surfactant under continuous ultrasonic vibration in the piezoelectric chamber. The size of the droplets was significantly reduced due to piezoelectric ultrasonic vibration. Under the provision of mild vacuum and heat generated by vibration, the organic solvent was evaporated, which leaves behind a suspension of SLN. In the present work, albendazole was selected as a model drug. Various trials with Compritol 888 ATO® and Precirol ATO 5® as a lipid carrier and Tween 80 and Poloxamer 188 as a surfactant were performed. Zeta potential of SLNs was improved by the addition of polyelectrolytes like K2SO4 and Na4P2O7. Result and Conclusion: The ratio of drug to lipid was optimized to 1:4 for the most favorable results. SLN with a minimum Z-average diameter of 98.59 nm, -21 mV zeta potential, and 34.064 % (SD 10.78, n=9) entrapment efficiency were developed using the Precirol ATO 5 ® as a lipid carrier. The proof of concept for this novel approach is established through the development of Albendazole SLNs. This approach must also be evaluated for the development of polymeric nanoparticles and vesicular formulations. The further sophistication of the frugal equipment may allow more control over the quality of SLN. This approach will enable underprivileged researchers to prepare Nanopharmaceuticals. Researchers and students of such institutions can focus on the application of SLN by resolving the constraint of sophisticated equipment with this novel approach. This novel approach should also be tried for polymeric and vesicular nanopharmaceuticals.


2019 ◽  
Vol 41 (6) ◽  
pp. 983-983
Author(s):  
Hadia Shoaib Hadia Shoaib ◽  
Sarfaraz Ahmed Mahesar Sarfaraz Ahmed Mahesar ◽  
Saeeduddin Saeeduddin ◽  
Parisa Jafarian Parisa Jafarian ◽  
Razieh Niazmand Razieh Niazmand ◽  
...  

Aim of present study was to evaluate quality of three collected sets of canola oil containing crude oil, neutralized oil, bleached oil, deodorized oil and canola oil deodorizer distillate (DD) form three different edible oil processing industries. Physiochemical properties such as moisture, color, free fatty acid (FFA), acid value (AV), peroxide value (PV), p-Anisidine value (AV), total oxidative (totox) value, saponification value (SV), iodine value (IV), unsaponifiable matter and soap content were evaluated. The results of the present study indicated that each stage of processing has different impact on the determined quality parameters. Overall processing was well controlled and final product i.e. refined, bleached and deodorized (RBD) canola oil was found to be fit for human consumption. Only soap contents should be further controlled during neutralization process to avoid extra processing time and losses in the bleaching process. High FFA contents in DD samples indicated that it could be used as a potential and cheap source for biodiesel production.


Author(s):  
Mohammad Reza Mehrabi ◽  
Mohammad Ali Shokrgozar ◽  
Tayebeh Toliyat ◽  
Masoomeh Shirzad ◽  
Azadeh Izadyari ◽  
...  

: Clinical application of vincristine sulfate as a chemotherapeutic agent is limited because of its low aqueous solubility and severe side effects. This study aimed to improve the bioavailability and reduce side effects of vincristine sulfate through entrapping in PEGylated niosomes. We evaluated the anticancer activity of PEGylated niosomal vincristine sulfate (PEG-nVCR) in a mouse model of lymphoma induced by BCL1 clone 5B1b cell line. PEG-nVCR was prepared by the thin-film hydration method. The prepared niosomes were characterized by size, zeta potential, and entrapment efficiency. The drug release pattern, neurotoxicity experiment, and in vivo anticancer activity of PEG-nVCR were evaluated by the dialysis diffusion method, rotarod performance test, and flow cytometry, respectively. The mean particle size, zeta potential, and entrapment efficiency of nisomes were obtained around 220 nm, -19 mV, and 81%, respectively. A sustained release behavior was indicated by PEG-nVCR so that the maximum release of VCR from niosomes reached to 69% after 36h of incubation. After the treatment of mice by different formulations, a significant reduction in lymphoma cells in the spleen was obtained for the PEG-nVCR, as compared to the free vincristine sulfate. In the neurotoxicity experiment, a 2.5-fold lower motor incoordination effect was observed for the PEG-nVCR group with respect to the free VCR group. According to these findings, it can be concluded that the PEGylated niosomal formulation could be a suitable carrier for the delivery of VCR to the lymphoma cells or other related cancer cells.


Sign in / Sign up

Export Citation Format

Share Document