scholarly journals Dog Wool Microparticles/Polyurethane Composite for Thermal Insulation

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1098 ◽  
Author(s):  
Francisco Claudivan da Silva ◽  
Helena P. Felgueiras ◽  
Rasiah Ladchumananandasivam ◽  
José Ubiragi L. Mendes ◽  
Késia Karina de O. Souto Silva ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Low Cost ◽  
Thermal Capacity ◽  
Thermal And Mechanical Properties ◽  
Composite Foam ◽  
Polyurethane Composite ◽  
Wool Fibers ◽  
Minimal Environmental Impact ◽  
Pu Foams ◽  
Thermal Stability Of

A polyurethane (PU)-based eco-composite foam was prepared using dog wool fibers as a filler. Fibers were acquired from pet shops and alkaline treated prior to use. The influence of their incorporation on the PU foams’ morphological, thermal, and mechanical properties was investigated. The random and disorganized presence of the microfibers along the foam influence their mechanical performance. Tensile and compression strengths were improved with the increased amount of dog wool microparticles on the eco-composites. The same occurred with the foams’ hydration capacity. The thermal capacity was also slightly enhanced with the incorporation of the fillers. The fillers also increased the thermal stability of the foams, reducing their dilatation with heating. The best structural stability was obtained using up to 120 °C with a maximum of 15% of filler. In the end, the dog wool waste was rationally valorized as a filler in PU foams, demonstrating its potential for insulation applications, with a low cost and minimal environmental impact.

Development of Rigid Biocomposite Polyurethane Foam for Load Bearing Application

2014 ◽  
Vol 68 (3) ◽  
Author(s):  
Mohd Haziq Dzulkifli ◽  
Mohd Yazid Yahya ◽  
Farhana Shakira Md Akhir ◽  
Rohah Abd Majid
Keyword(s):  
Compressive Strength ◽  
Palm Oil ◽  
Environmental Issues ◽  
Scanning Electron Micrographs ◽  
Composite Foam ◽  
Load Bearing ◽  
Polyurethane Composite ◽  
Pu Foam ◽  
Foam Production ◽  
Pu Foams

Polyurethane (PU) foams are widely used today in automotive and as insulation system. Due to environmental issues, efforts have been made to replace petrochemical polyol with natural-based polyol in PU foam production, without sacrificing any properties. This study aims as to produce palm oil-based polyurethane composite foam for load bearing purposes. Palm oil-based polyol (POP) was reacted with polymeric 4,4-diphenylmethane diisocyanate (p-MDI) with water as blowing agent and silicone surfactant to produce rigid PU foams. The foams obtained were varied by NCO:OH ratios and water content and characterized for their morphology and compressive strength. Scanning electron micrographs (SEM) indicated the cells within the obtained foams are closed cells. Compressive strength of obtained foams shows considerable improvement but only up to NCO:OH ratio of 1:1.35. 

scholarly journals Effect of Organic Modifier Types on the Physical–Mechanical Properties and Overall Migration of Post-Consumer Polypropylene/Clay Nanocomposites for Food Packaging

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1502
Author(s):  
Eliezer Velásquez ◽  
Sebastián Espinoza ◽  
Ximena Valenzuela ◽  
Luan Garrido ◽  
María José Galotto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Food Packaging ◽  
Clay Nanocomposites ◽  
Organic Modifier ◽  
Thermal And Mechanical Properties ◽  
Chemical Safety ◽  
Elongation At Break ◽  
Fatty Food ◽  
Recycled Plastics ◽  
Thermal Stability Of

The deterioration of the physical–mechanical properties and loss of the chemical safety of plastics after consumption are topics of concern for food packaging applications. Incorporating nanoclays is an alternative to improve the performance of recycled plastics. However, properties and overall migration from polymer/clay nanocomposites to food require to be evaluated case-by-case. This work aimed to investigate the effect of organic modifier types of clays on the structural, thermal and mechanical properties and the overall migration of nanocomposites based on 50/50 virgin and recycled post-consumer polypropylene blend (VPP/RPP) and organoclays for food packaging applications. The clay with the most hydrophobic organic modifier caused higher thermal stability of the nanocomposites and greater intercalation of polypropylene between clay mineral layers but increased the overall migration to a fatty food simulant. This migration value was higher from the 50/50 VPP/RPP film than from VPP. Nonetheless, clays reduced the migration and even more when the clay had greater hydrophilicity because of lower interactions between the nanocomposite and the fatty simulant. Conversely, nanocomposites and VPP/RPP control films exhibited low migration values in the acid and non-acid food simulants. Regarding tensile parameters, elongation at break values of PP film significantly increased with RPP addition, but the incorporation of organoclays reduced its ductility to values closer to the VPP.

scholarly journals Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Cost Effective ◽  
Tensile Tests ◽  
Thermal Stability Of

AbstractAdvanced medium-Mn sheet steels show an opportunity for the development of cost-effective and light-weight automotive parts with improved safety and optimized environmental performance. These steels utilize the strain-induced martensitic transformation of metastable retained austenite to improve the strength–ductility balance. The improvement of mechanical performance is related to the tailored thermal and mechanical stabilities of retained austenite. The mechanical stability of retained austenite was estimated in static tensile tests over a wide temperature range from 20 °C to 200 °C. The thermal stability of retained austenite during heating at elevated temperatures was assessed by means of dilatometry. The phase composition and microstructure evolution were investigated by means of scanning electron microscopy, electron backscatter diffraction, X-ray diffraction and transmission electron microscopy techniques. It was shown that the retained austenite stability shows a pronounced temperature dependence and is also stimulated by the manganese addition in a 3–5% range.

scholarly journals Upcycling of Vine Shoots: Production of Fillers for PHBV-Based Biocomposite Applications

2020 ◽  
Author(s):  
Grégoire David ◽  
Laurent Heux ◽  
Stéphanie Pradeau ◽  
Nathalie Gontard ◽  
Hélène Angellier-Coussy
Keyword(s):  
Water Vapor ◽  
Gas Phase ◽  
Mechanical Performance ◽  
Low Cost ◽  
Water Vapor Permeability ◽  
Contact Angles ◽  
Vapor Permeability ◽  
Water Contact ◽  
Median Diameter ◽  
Cost Of Materials

Abstract This paper aims at investigating the potential of vine shoots (ViSh) upcycling as fillers in novel poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) based biocomposites. ViSh particles of around 50 µm (apparent median diameter) were obtained combining dry grinding processes, and mixed with PHBV using melt extrusion. Thermal stability and elongation at break of biocomposites were reduced with increasing contents of ViSh particles (10, 20 and 30 wt%), while Young’s modulus and water vapor permeability were increased. It was shown that a surface gas-phase esterification allowed to significantly increase the hydrophobicity of ViSh particles (increase of water contact angles from 59° to 114°), leading to a reduction of 27% in the water vapor permeability of the biocomposite filled with 30 wt% of ViSh. The overall mechanical performance was not impacted by gas-phase esterification, demonstrating that the interfacial adhesion between the virgin ViSh particles and the PHBV matrix was already good and that such filler surface treatment was not required in that case. It was concluded that ViSh particles can be interestingly used as low cost fillers in PHBV-based biocomposites to decrease the overall cost of materials.

scholarly journals Color-Variable Photodynamic Antimicrobial Wool/Acrylic Blended Fabrics

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4141
Author(s):  
Tingting Wang ◽  
Wangbingfei Chen ◽  
Tingting Dong ◽  
Zihao Lv ◽  
Siming Zheng ◽  
...  
Keyword(s):  
Low Cost ◽  
Pathogen Transmission ◽  
Cationic Dyes ◽  
Light Illumination ◽  
Antibacterial Studies ◽  
Wool Fibers ◽  
Visible Light Illumination ◽  
Potential Applications ◽  
Dyed Fabrics ◽  
Acrylic Fibers

Towards the goal of developing scalable, economical and effective antimicrobial textiles to reduce infection transmission, here we prepared color-variable photodynamic materials comprised of photosensitizer (PS)-loaded wool/acrylic (W/A) blends. Wool fibers in the W/A blended fabrics were loaded with the photosensitizer rose bengal (RB), and the acrylic fibers were dyed with a variety of traditional cationic dyes (cationic yellow, cationic blue and cationic red) to broaden their color range. Investigations on the colorimetric and photodynamic properties of a series of these materials were implemented through CIELab evaluation, as well as photooxidation and antibacterial studies. Generally, the photodynamic efficacy of these dual-dyed fabrics was impacted by both the choice, and how much of the traditional cationic dye was employed in the dyeing of the W/A fabrics. When compared with the PS-only singly-dyed material, RB-W/A, that showed a 99.97% (3.5 log units; p = 0.02) reduction of Staphylococcus aureus under visible light illumination (λ ≥ 420 nm, 60 min), the addition of cationic dyes led to a slight decrease in the photoinactivation ability of the dual-dyed fabrics, but was still able to achieve a 99.3% inactivation of S. aureus. Overall, our findings demonstrate the feasibility and potential applications of low cost and color variable RB-loaded W/A blended fabrics as effective self-disinfecting textiles against pathogen transmission.

Influence of Melt Temperature on Compressive Plasticity of a Cu-Zr-Al Bulk Metallic Glass

2010 ◽  
Vol 146-147 ◽  
pp. 517-521
Author(s):  
Sheng Hui Xie ◽  
Xie Rong Zeng ◽  
Dong Ju Fu ◽  
Lei Zhao ◽  
Qiang Hu
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Metallic Glasses ◽  
Mechanical Performance ◽  
Casting Temperature ◽  
Thermal And Mechanical Properties ◽  
Micro Hardness ◽  
Melt Temperature ◽  
Hardness Tests ◽  
Important Solution

Cu47.5Zr47.5Al5 bulk metallic glasses (BMGs) were cast from the melt temperature 1143 to 1373 K. The structure, thermal and mechanical properties of the BMGs were investigated by XRD, DSC, HRTEM, dilatometric measurements, micro-hardness tests and uniaxial compression. The results indicate that the microstructure and mechanical performance of BMGs are closely affected by the casting temperature. Proper casting temperature ensures the BMGs with large relaxed excess free volume (REFV) and nano-crystallites, which favor the plastic deformation in Cu47.5Zr47.5Al5 BMGs. Regulating the preparing parameters is an important solution to good plasticity in BMGs.

Sign in / Sign up

Export Citation Format

Share Document