scholarly journals Mechanical, Wear and Thermal Behavior of Polyethylene Blended with Graphite Treated in Ball Milling

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 975
Author(s):  
Annamaria Visco ◽  
Antonio Grasso ◽  
Giuseppe Recca ◽  
Domenico Carmelo Carbone ◽  
Alessandro Pistone
Keyword(s):  
Ball Milling ◽  
Treatment Time ◽  
Wear Behavior ◽  
Low Cost ◽  
Market Demand ◽  
Low Friction ◽  
Mechanical Joints ◽  
Shock Absorbers ◽  
Previously Treated

Additive manufacturing, civil, and biomechanical applications are among the most important sectors, where the filler’s presence can significantly improve the quality of polymeric products blends. The high market demand of new low-cost material to be used as shock absorbers and mechanical joints arouses our curiosity to study a relatively common commercial polymer and filler. The possible improvement by blending high-density polyethylene (HDPE) and graphite was investigated for these sectors. To achieve this objective, we have prepared HDPE/graphite nanocomposites following mechanical treatment to understand which parameter provides the researched properties. As widely reported in the literature, milling treatment leads to the decrease of the particle size and the exfoliation of graphitic layers. Therefore, graphite has been previously treated with a ball mill for different times (1–16 h) to enhance its lubricating action. We checked an improvement in stiffness, yielding strength, thermal stability, and, in particularly, wear resistance that increased by 65% with respect to that of polyethylene (PE). A treatment time of eight hours in ball milling could be enough to give an appreciable improvement. The wear behavior of HDPE with treated graphite has not been deeply investigated so far, and it could be important because HDPE is considered a “carrier polymer” for different low-friction applications.

Effect of Computerized Auditory Training on Speech Perception of Adults With Hearing Impairment

2013 ◽  
Vol 20 (3) ◽  
pp. 91-106 ◽  
Author(s):  
Rachel Pizarek ◽  
Valeriy Shafiro ◽  
Patricia McCarthy
Keyword(s):  
Hearing Loss ◽  
Speech Perception ◽  
Literature Review ◽  
Low Cost ◽  
Experimental Designs ◽  
Auditory Training ◽  
Hearing Impairments ◽  
Communicative Disorders ◽  
And Training

Computerized auditory training (CAT) is a convenient, low-cost approach to improving communication of individuals with hearing loss or other communicative disorders. A number of CAT programs are being marketed to patients and audiologists. The present literature review is an examination of evidence for the effectiveness of CAT in improving speech perception in adults with hearing impairments. Six current CAT programs, used in 9 published studies, were reviewed. In all 9 studies, some benefit of CAT for speech perception was demonstrated. Although these results are encouraging, the overall quality of available evidence remains low, and many programs currently on the market have not yet been evaluated. Thus, caution is needed when selecting CAT programs for specific patients. It is hoped that future researchers will (a) examine a greater number of CAT programs using more rigorous experimental designs, (b) determine which program features and training regimens are most effective, and (c) indicate which patients may benefit from CAT the most.

The experience of using a diode laser in the herpes labial treatment

2020 ◽  
Vol 25 (1) ◽  
pp. 43-46
Author(s):  
S. L. Blashkova ◽  
E. V. Krikun ◽  
Yu. V. Fazylova ◽  
Yu. V. Blashkova
Keyword(s):  
Oral Cavity ◽  
Diode Laser ◽  
Comparison Group ◽  
Treatment Time ◽  
Local Treatment ◽  
Allergic Reactions ◽  
High Prevalence ◽  
Dental Diseases ◽  
Simplex Virus

Relevance. The relevance of the problem is in the high prevalence of the herpes simplex virus. According to WHO, nearly 90% of the population are carriers. Relapses can occur several times a year, which leads to disability and impairs the quality of life. Currently, there are a large number of drugs for general and local treatment. However, they are toxic and can cause allergic reactions. In recent years, a large number of studies have been devoted to the use of lasers in the treatment of dental diseases. Therefore, the question of the use of a laser in the treatment of herpetic lesions of the oral cavity remains relevant.Purpose. The research purpose was to determine the effectiveness of the use of a diode laser in the treatment of herpetic lesions of the lips.Materials and methods. We conducted a comparative assessment of the effectiveness of the use of a diode laser in monotherapy of herpetic lip lesions in 18 patients. The comparison group consisted of 18 patients, in the local treatment of which antiviral ointments were used.Results. The results of the study showed that the use of a diode laser can reduce treatment time, accelerate the epithelization of foci.Conclusion. The results of our study allow us to recommend the use of a diode laser in the complex treatment of herpetic lesions of the oral cavity.

The system of indicators of the quality of the carbon-carbon composite materials and technologies of their production

2018 ◽  
pp. 127-132
Author(s):  
T. N. Antipova ◽  
D. S. Shiroyan
Keyword(s):  
Composite Material ◽  
Low Cost ◽  
Experimental Studies ◽  
Carbon Matrix ◽  
Carbon Composite ◽  
Optimal Number ◽  
Laboratory Equipment ◽  
Carbon Composite Material ◽  
Carbon Composite Materials

The system of indicators of quality of carbon-carbon composite material and technological operations of its production is proved in the work. As a result of the experimental studies, with respect to the existing laboratory equipment, the optimal number of cycles of saturation of the reinforcing frame with a carbon matrix is determined. It was found that to obtain a carbon-carbon composite material with a low cost and the required quality indicators, it is necessary to introduce additional parameters of the pitch melt at the impregnation stage.

scholarly journals Preparation of Zn-MOFs by microwave-assisted ball milling for removal of tetracycline hydrochloride and Congo red from wastewater

2021 ◽  
Vol 10 (1) ◽  
pp. 125-133
Author(s):  
Qinhui Ren ◽  
Fuhua Wei ◽  
Hongliang Chen ◽  
Ding Chen ◽  
Bo Ding
Keyword(s):  
Ball Milling ◽  
Congo Red ◽  
Low Cost ◽  
Metal Organic Framework ◽  
Tetracycline Hydrochloride ◽  
Infrared Spectrometry ◽  
X Ray Diffraction ◽  
Wastewater Purification ◽  
Microwave Assisted ◽  
Metal Organic

Abstract In this study, we prepared Zn-MOFs as an ordinary, low-cost, and efficiency method taking advantage of zinc(ii) acetate monohydrate and 1,3,5-benzenetricarboxylic acid in microwave-assisted ball milling. The Zn-MOFs were measured via scanning electron microscopy, infrared spectrometry, X-ray diffraction, and thermogravimetry. We explored its use as a photocatalyst for the degradation of tetracycline hydrochloride and Congo red from aqueous solutions. The results demonstrate that the kinetic model was appropriate for the removal of organic pollutants. In general, it is feasible, inexpensive, and effective to use metal organic framework (MOF) to treat waste liquid. Therefore, our findings indicate that Zn-MOFs have broad application vista in wastewater purification.

scholarly journals Evaluation of Changes in Protein Quality of High-Pressure Treated Aqueous Aquafaba

Molecules ◽  
2021 ◽  
Vol 26 (1) ◽  
pp. 234
Author(s):  
Fatemah B. Alsalman ◽  
Hosahalli S. Ramaswamy
Keyword(s):  
High Pressure ◽  
Protein Quality ◽  
Treatment Time ◽  
Control Sample ◽  
Thermal Characteristics ◽  
Protein Digestibility ◽  
Foaming Properties ◽  
Freeze Dried ◽  
Cooking Water

Chickpea cooking water (CCW), known as aquafaba, has potential as a replacement for egg whites due to its emulsion and foaming properties which come from the proteins and starch that leach out from chickpeas into the cooking water. High pressure (HP) processing has the ability to modify the functional characteristics of proteins. It is hypothesized that HP processing could favorably affect the functional properties of CCW proteins by influencing their structure. The objective of this study to evaluate the effect of HP treatment on the associated secondary structure, emulsion properties and thermal characteristics of CCW proteins. A central composite rotatable design is used with pressure level (227–573 MPa) and treatment time (6–24 min) as HP variables, and concentration of freeze dried CCW aquafaba powder (11–29%) as product variable, and compared to untreated CCW powder. HP improves aquafaba emulsion properties compared to control sample. HP reduces protein aggregates by 33.3%, while β-sheets decreases by 4.2–87.6% in which both correlated to increasing protein digestibility. α-helices drops by 50%. It affects the intensity of some HP treated samples, but not the trend of bands in most of them. HP treatment decreases Td and enthalpy because of increasing the degree of denaturation.

scholarly journals Influence of End Mill Manufacturing on Cutting Edge Quality and Wear Behavior

2021 ◽  
Vol 5 (3) ◽  
pp. 77
Author(s):  
Berend Denkena ◽  
Alexander Krödel-Worbes ◽  
Sascha Beblein ◽  
Markus Hein
Keyword(s):  
Wear Behavior ◽  
Cutting Edge ◽  
End Mills ◽  
Edge Quality ◽  
Manufacturing Process Chain ◽  
The Individual ◽  
Application Specific ◽  
Milling Tools ◽  
Edge Preparation

One of the decisive factors for the performance of milling tools is the quality of the cutting edge. The latter results from the process control of the individual steps along the tool manufacturing process chain, which generally includes the sintering or pressing of the blanks, grinding, cutting edge preparation, and coating of the tools. However, the targeted and application-specific design of the process steps in terms of high economic efficiency is currently limited by a lack of knowledge regarding the influence of the corresponding process parameters on the resulting cutting edge quality. In addition, there is a lack of suitable parameters that adequately represent the characteristics of the cutting edge microtopography. This publication therefore investigates the influence of manufacturing processes on cutting edge quality and wear behavior of end mills. On this basis, different characterization parameters for the cutting edge quality are derived and evaluated with regard to their ability to predict the wear behavior.

scholarly journals Diagnostic Capabilities of a Smartphone- Based Low-Cost Microscope

2020 ◽  
Vol 6 (3) ◽  
pp. 522-525
Author(s):  
Dorina Hasselbeck ◽  
Max B. Schäfer ◽  
Kent W. Stewart ◽  
Peter P. Pott
Keyword(s):  
Low Cost ◽  
Field Of View ◽  
Parasitic Diseases ◽  
Optical Parameters ◽  
Trade Off ◽  
Resource Limited ◽  
Wide Range ◽  
Diagnostic Applications ◽  
Diagnostic Capabilities

AbstractMicroscopy enables fast and effective diagnostics. However, in resource-limited regions microscopy is not accessible to everyone. Smartphone-based low-cost microscopes could be a powerful tool for diagnostic and educational purposes. In this paper, the imaging quality of a smartphone-based microscope with four different optical parameters is presented and a systematic overview of the resulting diagnostic applications is given. With the chosen configuration, aiming for a reasonable trade-off, an average resolution of 1.23 μm and a field of view of 1.12 mm2 was achieved. This enables a wide range of diagnostic applications such as the diagnosis of Malaria and other parasitic diseases.

scholarly journals Current Trends in Polymer Based Sensors

Chemosensors ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 108
Author(s):  
Giancarla Alberti ◽  
Camilla Zanoni ◽  
Vittorio Losi ◽  
Lisa Rita Magnaghi ◽  
Raffaela Biesuz
Keyword(s):  
Chemical Structure ◽  
Low Cost ◽  
Sensing Applications ◽  
Current Trends ◽  
Manufacturing Methods ◽  
New Devices

This review illustrates various types of polymer and nanocomposite polymeric based sensors used in a wide variety of devices. Moreover, it provides an overview of the trends and challenges in sensor research. As fundamental components of new devices, polymers play an important role in sensing applications. Indeed, polymers offer many advantages for sensor technologies: their manufacturing methods are pretty simple, they are relatively low-cost materials, and they can be functionalized and placed on different substrates. Polymers can participate in sensing mechanisms or act as supports for the sensing units. Another good quality of polymer-based materials is that their chemical structure can be modified to enhance their reactivity, biocompatibility, resistance to degradation, and flexibility.

Sign in / Sign up

Export Citation Format

Share Document