scholarly journals Foamability of Cellulose Palmitate Using Various Physical Blowing Agents in the Extrusion Process

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2416
Author(s):  
Teijo Rokkonen ◽  
Pia Willberg-Keyriläinen ◽  
Jarmo Ropponen ◽  
Tero Malm
Keyword(s):  
Cell Size ◽  
Extrusion Process ◽  
Foam Formation ◽  
Polymer Foams ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
Blowing Agents ◽  
Die Temperature ◽  
Carbon Dioxide Co2

Polymer foams are widely used in several fields such as thermal insulation, acoustics, automotive, and packaging. The most widely used polymer foams are made of polyurethane, polystyrene, and polyethylene but environmental awareness is boosting interest towards alternative bio-based materials. In this study, the suitability of bio-based thermoplastic cellulose palmitate for extrusion foaming was studied. Isobutane, carbon dioxide (CO2), and nitrogen (N2) were tested as blowing agents in different concentrations. Each of them enabled cellulose palmitate foam formation. Isobutane foams exhibited the lowest density with the largest average cell size and nitrogen foams indicated most uniform cell morphology. The effect of die temperature on foamability was further studied with isobutane (3 wt%) as a blowing agent. Die temperature had a relatively low impact on foam density and the differences were mainly encountered with regard to surface quality and cell size distribution. This study demonstrates that cellulose palmitate can be foamed but to produce foams with greater quality, the material homogeneity needs to be improved and researched further.

Growth and Cell-Size Distribution of Marine Planktonic Algae in Batch and Dialysis Cultures

1973 ◽  
Vol 30 (2) ◽  
pp. 143-155 ◽  
Author(s):  
A. Prakash ◽  
Liv Skoglund ◽  
Britt Rystad ◽  
Arne Jensen
Keyword(s):  
Size Distribution ◽  
Cell Size ◽  
Growth Cycle ◽  
Exponential Growth Phase ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
Planktonic Algae ◽  
Maximum Cell ◽  
Dialysis Culture

An extended exponential growth phase and a higher maximum population characterized growth of planktonic algae in a dialysis system compared with that in a batch system. Algal cells grown in a dialysis culture had higher chlorophyll content and a larger average cell size than those grown in a batch culture. In both types of culture, changes in cell-size distribution were related to the phases of the growth cycle with maximum cell-size during the stationary phase. Various interactions of the component reactions of photosynthesis leading to changes in growth pattern and cell-size distribution are discussed.

Effect of Nanoclay on the Physical-Mechanical and Thermal Properties and Microstructure of Extruded Noncross-Linked LDPE Nanocomposite Foams

2011 ◽  
Vol 471-472 ◽  
pp. 751-756 ◽  
Author(s):  
F. Zandi ◽  
M. Rezaei ◽  
A. Kasiri
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Cell Size ◽  
Flame Retardancy ◽  
Image Analyzer ◽  
Mechanical And Thermal Properties ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
Nanocomposite Foams

Novel noncross-linked low density polyethylene (LDPE) foams were produced by extrusion process. In this study the effects of Organophilic Montmorillonite (OMMT) nanoclay (DK1) on thermal conductivity, flame retardancy, morphological and mechanical properties of LDPE foams have been investigated. Nanoclay dispersion in LDPE foam structure was examined by X-ray diffraction (XRD), microstructure was observed by an optical microscope and analyzed by Bel View image analyzer, thermal conductivity was studied by a simple transient method, mechanical properties was investigated using a tensile-compression Zwick-Roell machine as well as the flame retardancy of the samples was examined by flammability test. The optimum nanoclay content was determined by comparison of the properties in nanocomposite and neat LDPE foams. Due to the presence of nanoclay in the foam and decreasing the cell nucleation energy around the nanoclay, the average cell size was decreased as well as the cell density and microstructure uniformity was increased. In XRD patterns of LDPE nanocomposite foams, OMMT (DK1) characteristic peak was not observed as evidence of nanoclay intercalation-exfoliation in the polymer matrix, which led to the production of foams with homogenous microstructure. Furthermore, this nanocomposites showed lower thermal conductivity compared to neat LDPE foam, which can be attributed to the cell size reduction as well as narrow cell size distribution in nanocomposite foams. Compression test results demonstrated that LDPE nanocomposite foams with proper clay contents have improved mechanical properties (Young’s modulus, compressive strength). Furthermore due to the presence of DK1 nanoclay, LDPE foam showed a good char formation as an evidence of their flame retardancy.

Characterization of LDMMs

MRS Bulletin ◽  
1990 ◽  
Vol 15 (12) ◽  
pp. 41-43
Keyword(s):  
Spatial Scale ◽  
Cell Size ◽  
Three Dimensional ◽  
Morphological Properties ◽  
Sem Images ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
Process Step ◽  
Size Standard

The previous sections of this article described the synthesis, morphologies, and properties of a variety of low-density microcellular materials. This section discusses several of the analytical methods used and developed at the DOE laboratories to characterize these state-of-the-art materials.In some LDMM applications, quantitative measurements of the material's average cell size and cell size distribution are desired. Indeed, the term “microcellular” has little meaning without such information. As seen throughout this article, however, most LDMMs do not have a readily defined cellular character. The more general problem is to quantify the spatial scale(s) of the foam. For this purpose it is necessary to define one or more “measures” of the spatial scale. The possibilities are many and include not only single numbers (e.g., cell size and cell size standard deviation, where “cell size” is meaningful) but also functional descriptions (e.g., correlation functions).SEM provides direct images and, therefore, is the most popular technique for examining LDMM morphology. SEM, however, suffers from at least three limitations: (1) SEM examines only a very small volume of material, and thus is impractical for obtaining average morphological properties; (2) SEM requires that nonconductive LDMMs be coated, a process step that can alter the structure and introduce artifacts (particularly with delicate structures); and (3) SEM images are only two-dimensional projections of real three-dimensional structures.

The Influence of Melt Elongational Properties on the Morphology of PES Cellular Materials

2002 ◽  
Vol 21 (6) ◽  
pp. 445-454 ◽  
Author(s):  
Frank Wöllecke ◽  
Volker Altstädt ◽  
Jan Sandler ◽  
Dietmar Rakutt
Keyword(s):  
Molecular Weight ◽  
Cell Size ◽  
Foam Cell ◽  
Batch Process ◽  
Processing Conditions ◽  
Compressive Properties ◽  
Polymer Molecular Weight ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell

Rheotens melt elongational experiments were performed to evaluate polyethersulfone with regard to its foamability. The effect of polymer molecular weight was correlated with the resulting foam cell morphology achieved under identical processing conditions in a batch process. It appears, that the melt strength of the polyethersulfone governs the average cell size, cell size distribution, as well as cell wall rupture during expansion and the corresponding compressive properties of the foam. These effects were further verified by a variation of the blowing agent content for polyethersulfone with a given molecular weight.

Morphological Analysis of Foamed HDPE/LLDPE Blends by X-ray Micro-Tomography: Effect of Blending, Mixing Intensity and Foaming Temperature

2017 ◽  
Vol 36 (5) ◽  
pp. 221-250 ◽  
Author(s):  
Peyman Shahi ◽  
Amir Hossein Behravesh ◽  
Sheikh Rasel ◽  
Ghaus Rizvi ◽  
Remon Pop-Iliev
Keyword(s):  
Cell Size ◽  
Void Fraction ◽  
Cellular Structure ◽  
3D Analysis ◽  
Average Cell Size ◽  
Cell Size Distribution ◽  
Average Cell ◽  
X Ray ◽  
Wide Range ◽  
Foaming Temperature

Non-invasive x-ray micro-computed tomography was employed for thorough quantitative and qualitative analysis of the cellular structure of foams made of linear low density polyethylene (LLDPE), high density polyethylene (HDPE) and their blends. Special emphasis was given to the differences between the results of 3D and 2D analyses, to evaluate the possible errors while studying the morphology using conventional 2D techniques (e.g. SEM). Blends with the weight compositions of 90%LLDPE/10%HDPE and 75%LLDPE/25%HDPE were produced at different rotor speeds of 10, 60 and 120 rpm and batch foaming was examined over a wide range of temperature. The void fraction values from 2D and 3D analysis were found to agree well with those obtained with the Archimedes method. Results showed more uniform cell size distribution for blends mixed at the lower spectrum of screw rotational speed. Among the blends with higher void fraction values and relatively uniform cellular structure, higher average cell size (3–30%) and cell population density (1.25–2.5 times) were noticed in 3D analysis compared with 2D data. The micro-CT images at different cross sections revealed anisotropic cell growth and more elongated cells along the thickness of the specimen. It was also observed that, with increase in foaming temperature, cell shrink prevailed over cell coalescence in the samples with lower viscosity (prepared at low rpm of 10), while for those with higher viscosity (prepared at an rpm of 60) cell coalescence was more dominant.

Characterization of microstructures of SAN foam core using micro-computed tomography

2021 ◽  
pp. 026248932110068
Author(s):  
Youming Chen ◽  
Raj Das ◽  
Hui Wang ◽  
Mark Battley
Keyword(s):  
Cell Wall ◽  
Cell Size ◽  
Wall Thickness ◽  
Strain Localization ◽  
Cell Wall Thickness ◽  
Micro Computed Tomography ◽  
Average Cell Size ◽  
Average Cell ◽  
3D Images ◽  
Compressive Tests

In this study, the microstructure of a SAN foam was imaged using a micro-CT scanner. Through image processing and analysis, variations in density, cell wall thickness and cell size in the foam were quantitatively explored. It is found that cells in the foam are not elongated in the thickness (or rise) direction of foam sheets, but rather equiaxed. Cell walls in the foam are significantly straight. Density, cell size and cell wall thickness all vary along the thickness direction of foam sheets. The low density in the vicinity of one face of foam sheets leads to low compressive stiffness and strength, resulting in the strain localization observed in our previous compressive tests. For M80, large open cells on the top face of foam sheets are likely to buckle in compressive tests, therefore being another potential contributor to the strain localization as well. The average cell wall thickness measured from 2D slice images is around 1.4 times that measured from 3D images, and the average cell size measured from 2D slice images is about 13.8% smaller than that measured from 3D images. The dispersions of cell wall thickness measured from 2D slice images are 1.16–1.20 times those measured from 3D images. The dispersions of cell size measured from 2D slice images are 1.12–1.36 times those measured from 3D images.

The effect of organofluorine additives on the morphology, thermal conductivity and mechanical properties of rigid polyurethane and polyisocyanurate foams

2021 ◽  
pp. 0021955X2098715
Author(s):  
Cosimo Brondi ◽  
Ernesto Di Maio ◽  
Luigi Bertucelli ◽  
Vanni Parenti ◽  
Thomas Mosciatti
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Cell Size ◽  
Flexural Properties ◽  
Anisotropy Ratio ◽  
Cell Content ◽  
Average Cell Size ◽  
Average Cell ◽  
Thermal Insulating ◽  
Liquid Type

This study investigates the effect of liquid-type organofluorine additives (OFAs) on the morphology, thermal conductivity and mechanical properties of rigid polyurethane (PU) and polyisocyanurate (PIR) foams. Foams were characterized in terms of their morphology (density, average cell size, anisotropy ratio, open cell content), thermal conductivity and compressive as well as flexural properties. Based on the results, we observed that OFAs efficiently reduced the average cell size of both PU and PIR foams, leading to improved thermal insulating and mechanical properties.

Shear Induced Low- and High-Angle Boundary Characterization Using Kikuchi Bands in Transmission Electron Microscopy

2008 ◽  
Vol 584-586 ◽  
pp. 293-299 ◽  
Author(s):  
Marcello Cabibbo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Cell Size ◽  
Grain Structure ◽  
Structure Evolution ◽  
High Angle ◽  
Boundary Misorientation ◽  
Average Cell Size ◽  
Average Cell ◽  
Transmission Electron

Microstructure evolution with equal channel angular pressing (ECAP) using route Bc, that is a 90° axial rotation of the billet between passes, up to 8 passes, was investigated by transmission electron microscopy. The study has been focused on the induced development of boundary misorientation and spacing toward microstructure refinement. Cell (low-angle) and grain (high-angle) misorientation and spacing were determined from about 250 boundaries per pass of ECAP, systematically using whether Kikuchi patterns or Moiré fringes, these latter where possible. The average cell size and misorientation saturate within the first two passes. Misorientation and spacing of high-angle boundaries decrease with the number of passes. After 8 passes, mean cell size is ≈ 1.3 µm and the fraction of high-angle boundaries is ≈ 0.7. Differences in rate of grain structure evolution per pass are linked to differences in ability of dislocations introduced in new passes to recombine with the existing ones. As ECAP strain rises, the misorientation distribution develops strong deviations from the MacKenzie distribution for statistical grain orientation. This is interpreted as a result of the tendency to form equiaxed grains in a textured grain structure.

Multiple effects of serum low-density lipoprotein on cultured human fibroblasts

1979 ◽  
Vol 57 (6) ◽  
pp. 684-691 ◽  
Author(s):  
M. J. Spain ◽  
L. O. Wosu ◽  
N. Kalant
Keyword(s):  
Cell Size ◽  
Human Fibroblasts ◽  
Density Lipoprotein ◽  
Cell Protein ◽  
Temporary Increase ◽  
Low Density ◽  
Cell Content ◽  
Average Cell Size ◽  
Platelet Factor ◽  
Average Cell

The effects of serum low-density lipoproteins (LDL) were studied in cultures of human skin fibroblasts grown in medium supplemented with human serum deficient in lipoproteins and in platelet factor. The LDL led to a temporary increase in the rate of cell replication, to increases in the cell content of protein and cholesterol, to an increase in average cell size, and to an increased secretion of glycosaminoglycans. The increases in cholesterol and protein were proportional to the increase in cell size, suggesting that the additional protein and cholesterol were of a structural, rather than a storage, nature. The increase in cell protein during the first few days of exposure to LDL was due to a decrease in the rate of protein degradation. Ultrafiltration of the serum to remove substances of molecular weight < 30 000 did not reduce the basal rate of cell proliferation but did prevent the stimulation of proliferation by LDL; it did not alter the effect of LDL on cell protein and cholesterol, indicating that the latter responses are independent of the mitogenic action. The response of cells from diabetic donors did not differ from that of normal cells.

DAPI direct counting underestimates bacterial abundances and average cell size compared to AO direct counting

1993 ◽  
Vol 38 (7) ◽  
pp. 1566-1570 ◽  
Author(s):  
Marcelino T. Suzuki ◽  
Evelyn B. Sherr ◽  
Barry F. Sherr
Keyword(s):  
Cell Size ◽  
Average Cell Size ◽  
Average Cell ◽  
Direct Counting
Sign in / Sign up

Export Citation Format

Share Document