scholarly journals Use of Biochar as Filler for Biocomposite Blown Films: Structure-Processing-Properties Relationships

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3953
Author(s):  
Luigi Botta ◽  
Rosalia Teresi ◽  
Vincenzo Titone ◽  
Giusi Salvaggio ◽  
Francesco Paolo La Mantia ◽  
...  
Keyword(s):  
Tensile Tests ◽  
Film Blowing ◽  
Water Contact ◽  
Blown Films ◽  
Angle Measurements ◽  
Biocomposite Films ◽  
Oxidative Resistance ◽  
Twin Screw ◽  
Mechanical Performances ◽  
Processing Properties

In this work, biocomposite blown films based on poly(butylene adipate-co-terephthalate) (PBAT) as biopolymeric matrix and biochar (BC) as filler were successfully fabricated. The materials were subjected to a film-blowing process after being compounded in a twin-screw extruder. The preliminary investigations conducted on melt-mixed PBAT/BC composites allowed PBAT/BC 5% and PBAT/BC 10% to be identified as the most appropriate formulations to be processed via film blowing. The blown films exhibited mechanical performances adequate for possible application as film for packaging, agricultural, and compost bags. The addition of BC led to an improvement of the elastic modulus, still maintaining high values of deformation. Water contact angle measurements revealed an increase in the hydrophobic behavior of the biocomposite films compared to PBAT. Additionally, accelerated degradative tests monitored by tensile tests and spectroscopic analysis revealed that the filler induced a photo-oxidative resistance on PBAT by delaying the degradation phenomena.

scholarly journals Preparation and characterization of polyethylene glycol/poly(L-lactic acid) blends

2017 ◽  
Vol 89 (1) ◽  
pp. 141-152 ◽  
Author(s):  
Ioanna-Georgia Athanasoulia ◽  
Petroula A. Tarantili
Keyword(s):  
Contact Angle ◽  
Lactic Acid ◽  
Degradation Process ◽  
Water Contact ◽  
Wetting Ability ◽  
Angle Measurements ◽  
Low Concentrations ◽  
Contact Angle Measurements ◽  
Twin Screw ◽  
Poly Ethylene

AbstractThe effect of incorporation of poly(ethylene glycol) (PEG) on thermomechanical and hydrophilicity properties of poly(L-lactic acid) (PLLA) was investigated. PEG/PLLA blends, containing 10, 20, 30 and 40 wt% PEG, were prepared by melt-extrusion in a co-rotating twin-screw extruder. By DSC analysis, it was observed that the Tg of PLLA phase in PEG/PLLA blends decreased accompanied by a significant decrease in Tcc and increase in their melting enthalpy. Therefore, the addition of PEG enhances the crystallization ability of PLLA phase due to its lubricating effect which increased mobility of PLLA chains. From TGA it was observed that low concentrations of PEG (10 & 20 wt%) increase the Tonset of thermal degradation, probably due to improved heat resistance of the crystalline phase. At higher PEG content, the Tonset decreases, as the lubricating effect becomes the controlling mechanism for the initiation of degradation process. Decrease in tensile strength and modulus was recorded especially in PLLA blends with PEG content higher than 20 wt%. The elongation at break decreases reaching a maximum at 20 wt% PEG and then dropped again. To investigate the effect of PEG on the wetting ability of PLLA, water contact angle measurements were performed. The results indicate that the introduction of PEG lowers the contact angle values in PEG/PLLA film surfaces, as compared to pure PLLA, suggesting improved hydrophilic properties.

scholarly journals Bionanocomposite Blown Films: Insights on the Rheological and Mechanical Behavior

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1167
Author(s):  
Maria Chiara Mistretta ◽  
Luigi Botta ◽  
Rossella Arrigo ◽  
Francesco Leto ◽  
Giulio Malucelli ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Viscoelastic Behavior ◽  
Elongational Flow ◽  
Marginal Effect ◽  
Film Blowing ◽  
Rheological Characterization ◽  
Polyethylene Matrix ◽  
Blown Films ◽  
Twin Screw ◽  
Industrial Level

In this work, bionanocomposites based on two different types of biopolymers belonging to the MaterBi® family and containing two kinds of modified nanoclays were compounded in a twin-screw extruder and then subjected to a film blowing process, aiming at obtaining sustainable films potentially suitable for packaging applications. The preliminary characterization of the extruded bionanocomposites allowed establishing some correlations between the obtained morphology and the material rheological and mechanical behavior. More specifically, the morphological analysis showed that, regardless of the type of biopolymeric matrix, a homogeneous nanofiller dispersion was achieved; furthermore, the established biopolymer/nanofiller interactions caused a restrain of the dynamics of the biopolymer chains, thus inducing a significant modification of the material rheological response, which involves the appearance of an apparent yield stress and the amplification of the elastic feature of the viscoelastic behavior. Besides, the rheological characterization under non-isothermal elongational flow revealed a marginal effect of the embedded nanofillers on the biopolymers behavior, thus indicating their suitability for film blowing processing. Additionally, the processing behavior of the bionanocomposites was evaluated and compared to that of similar systems based on a low-density polyethylene matrix: this way, it was possible to identify the most suitable materials for film blowing operations. Finally, the assessment of the mechanical properties of the produced blown films documented the potential exploitation of the selected materials for packaging applications, also at an industrial level.

Nanostructured Polymer Brushes With Reversibly Changing Properties

2002 ◽  
Vol 727 ◽  
Author(s):  
Denys Usov ◽  
Manfred Stamm ◽  
Sergiy Minko ◽  
Christian Froeck ◽  
Andreas Scholl ◽  
...  
Keyword(s):  
Polymer Brushes ◽  
Phase Segregation ◽  
Water Contact ◽  
Angle Measurements ◽  
Nanostructured Polymer ◽  
Contact Angle Measurements ◽  
Vertical Segregation ◽  
Oxygen Plasma Etching ◽  
Grafting From ◽  
Photoemission Electron

AbstractWe investigated the interplay between different mechanisms of the lateral and vertical segregation in the synthesized via “grafting from” approach symmetric A/B (where A and B are poly(styrene-co-2,3,4,5,6-pentafluorostyrene) and poly(methylmethacrylate), respectively) polymer brushes upon exposure to different solvents. We used X-ray photoemission electron spectroscopy and microscopy (X-PEEM), AFM, water contact angle measurements, and oxygen plasma etching to study morphology of the brushes. The ripple morphology after toluene (nonselective solvent) revealed elongated lamellar-like domains of A and B polymers alternating across the surface. The dimple-A morphology consisting of round clusters of the polymer A was observed after acetone (selective solvent for B). The top layer was enriched with the polymer B showing that the brush underwent both the lateral and vertical phase segregation. A qualitative agreement with predictions of SCF theory was found.

Effect of Microcrystalline Cellulose from Banana Stem Fiber on Mechanical Properties and Crystallinity of PLA Composite Films

2011 ◽  
Vol 695 ◽  
pp. 170-173 ◽  
Author(s):  
Voravadee Suchaiya ◽  
Duangdao Aht-Ong
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Microcrystalline Cellulose ◽  
Young's Modulus ◽  
Agricultural Waste ◽  
Composite Films ◽  
Sem Image ◽  
Biocomposite Films ◽  
Twin Screw ◽  
Banana Stem

This work focused on the preparation of the biocomposite films of polylactic acid (PLA) reinforced with microcrystalline cellulose (MCC) prepared from agricultural waste, banana stem fiber, and commercial microcrystalline cellulose, Avicel PH 101. Banana stem microcrystalline cellulose (BS MCC) was prepared by three steps, delignification, bleaching, and acid hydrolysis. PLA and two types of MCC were processed using twin screw extruder and fabricated into film by a compression molding. The mechanical and crystalline behaviors of the biocomopsite films were investigated as a function of type and amount of MCC. The tensile strength and Young’s modulus of PLA composites were increased when concentration of MCC increased. Particularly, banana stem (BS MCC) can enhance tensile strength and Young’s modulus of PLA composites than the commercial MCC (Avicel PH 101) because BS MCC had better dispersion in PLA matrix than Avicel PH 101. This result was confirmed by SEM image of fractured surface of PLA composites. In addition, XRD patterns of BS MCC/PLA composites exhibited higher crystalline peak than that of Avicel PH 101/PLA composites

scholarly journals On the Effectiveness of Oxygen Plasma and Alkali Surface Treatments to Modify the Properties of Polylactic Acid Scaffolds

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1643
Author(s):  
Ricardo Donate ◽  
María Elena Alemán-Domínguez ◽  
Mario Monzón
Keyword(s):  
Surface Properties ◽  
Enzymatic Degradation ◽  
Oxygen Plasma ◽  
Physicochemical Characterization ◽  
Surface Treatments ◽  
Carboxyl Groups ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Angle Measurements ◽  
3D Printed

Surface modification of 3D-printed PLA structures is a major issue in terms of increasing the biofunctionality and expanding the tissue engineering applications of these parts. In this paper, different exposure times were used for low-pressure oxygen plasma applied to PLA 3D-printed scaffolds. Alkali surface treatments were also evaluated, aiming to compare the modifications introduced on the surface properties by each strategy. Surface-treated samples were characterized through the quantification of carboxyl groups, energy-dispersive X-ray spectroscopy, water contact angle measurements, and differential scanning calorimetry analysis. The change in the surface properties was studied over a two-week period. In addition, an enzymatic degradation analysis was carried out to evaluate the effect of the surface treatments on the degradation profile of the 3D structures. The physicochemical characterization results suggest different mechanism pathways for each type of treatment. Alkali-treated scaffolds showed a higher concentration of carboxyl groups on their surface, which enhanced the enzymatic degradation rate, but were also proven to be more aggressive towards 3D-printed structures. In contrast, the application of the plasma treatments led to an increased hydrophilicity of the PLA surface without affecting the bulk properties. However, the changes on the properties were less steady over time.

scholarly journals Epoxy/alumina composite coating on welded steel 316L with excellent wear and anticorrosion properties

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Maryama Hammi ◽  
Younes Ziat ◽  
Zakaryaa Zarhri ◽  
Charaf Laghlimi ◽  
Abdelaziz Moutcine
Keyword(s):  
Electrochemical Behaviour ◽  
Sem Analysis ◽  
Water Contact ◽  
Welded Steel ◽  
Melted Zone ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Alumina Composite ◽  
The Cost ◽  
Good Contrast

AbstractThe main purpose of this study is to elaborate anticorrosive coatings for the welded steel 316L, since this later is widely used in industrial field. Hence, within this work we have studied the electrochemical behaviour of different zones of the welded steel 316 in 1 M HCl media. The macrography study of the welded steel has revealed the different areas with a good contrast. We have stated three different zones, namely; melted zone (MZ), heat affected zone (HAZ) and base metal zone (BM). Impedance studies on welded steel 316L were conducted in 1 M HCl solution, coating of Epoxy/Alumina composite was applied on different zones, in order to reveal the anti-corrosion efficiency in each zone. Scanning electron microscopy (SEM) analysis was undertaken in order to check how far the used coating in such aggressive media protects the studied zones and these findings were assessed by water contact angle measurements. The choice of this coating is based on the cost and the safety. We concluded that the Epoxy/Alumina composite has a good protecting effect regarding welded steel in aggressive media.

scholarly journals Cellulose Acetate-Based Electrospun Materials with a Variety of Biological Potentials: Antibacterial, Antifungal and Anticancer

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1631
Author(s):  
Mariya Spasova ◽  
Nevena Manolova ◽  
Iliya Rashkov ◽  
Petya Tsekova ◽  
Ani Georgieva ◽  
...  
Keyword(s):  
Cellulose Acetate ◽  
Mechanical Tests ◽  
Fibrous Materials ◽  
Water Contact ◽  
Antibacterial And Antifungal Activities ◽  
3T3 Fibroblasts ◽  
Angle Measurements ◽  
Zones Of Inhibition ◽  
Model Drug ◽  
Antibacterial And Antifungal

Novel eco-friendly fibrous materials with complex activities from cellulose acetate and cellulose acetate/polyethylene glycol (CA,PEG) containing 5-chloro-8-hydroxyquinoline as a model drug were obtained by electrospinning. Several methods, including scanning electron microscopy, X-ray diffraction analysis, ultraviolet-visible spectroscopy, water contact angle measurements, and mechanical tests, were utilized to characterize the obtained materials. The incorporation of PEG into the fibers facilitated the drug release. The amounts of the released drug from CA/5-Cl8Q and CA,PEG/5-Cl8Q were 78 ± 3.38% and 86 ± 3.02%, respectively (for 175 min). The antibacterial and antifungal activities of the obtained materials were studied. The measured zones of inhibition of CA/5-Cl8Q and CA,PEG/5-Cl8Q mats were 4.0 ± 0.18 and 4.5 ± 0.2 cm against S. aureus and around 4.0 ± 0.15 and 4.1 ± 0.22 cm against E. coli, respectively. The complete inhibition of the C. albicans growth was detected. The cytotoxicity of the obtained mats was tested toward HeLa cancer cells, SH-4 melanoma skin cells, and mouse BALB/c 3T3 fibroblasts as well. The CA/5-Cl8Q and CA,PEG/5-Cl8Q materials exhibited anticancer activity and low normal cell toxicity. Thus, the obtained fibrous materials can be suitable candidates for wound dressing applications and for application in local cancer treatment.

scholarly journals PLA-Based Hybrid and Composite Electrospun Fibrous Scaffolds as Potential Materials for Tissue Engineering

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Anna Magiera ◽  
Jarosław Markowski ◽  
Elzbieta Menaszek ◽  
Jan Pilch ◽  
Stanislaw Blazewicz
Keyword(s):  
Tissue Engineering ◽  
Mechanical Tests ◽  
Hybrid Structures ◽  
Poly Lactic Acid ◽  
Electrospinning Technique ◽  
Water Contact ◽  
Human Osteoblasts ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Normal Human

The aim of the study was to manufacture poly(lactic acid)- (PLA-) based nanofibrous nonwovens that were modified using two types of modifiers, namely, gelatin- (GEL-) based nanofibres and carbon nanotubes (CNT). Hybrid nonwovens consisting of PLA and GEL nanofibres (PLA/GEL), as well as CNT-modified PLA nanofibres with GEL nanofibres (PLA + CNT/GEL), in the form of mats, were manufactured using concurrent-electrospinning technique (co-ES). The ability of such hybrid structures as potential scaffolds for tissue engineering was studied. Both types of hybrid samples and one-component PLA and CNTs-modified PLA mats were investigated using scanning electron microscopy (SEM), water contact angle measurements, and biological and mechanical tests. The morphology, microstructure, and selected properties of the materials were analyzed. Biocompatibility and bioactivity in contact with normal human osteoblasts (NHOst) were studied. The coelectrospun PLA and GEL nanofibres retained their structures in hybrid samples. Both types of hybrid nonwovens were not cytotoxic and showed better osteoinductivity in comparison to scaffolds made from pure PLA. These samples also showed significantly reduced hydrophobicity compared to one-component PLA nonwovens. The CNT-contained PLA nanofibres improved mechanical properties of hybrid samples and such a 3D system appears to be interesting for potential application as a tissue engineering scaffold.

scholarly journals Filling of Mater-Bi with Nanoclays to Enhance the Biofilm Rigidity

2018 ◽  
Vol 9 (4) ◽  
pp. 60 ◽  
Author(s):  
Giuseppe Cavallaro ◽  
Giuseppe Lazzara ◽  
Lorenzo Lisuzzo ◽  
Stefana Milioto ◽  
Filippo Parisi
Keyword(s):  
Tensile Properties ◽  
Food Packaging ◽  
Mechanical Response ◽  
Materials Science ◽  
Traction Force ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Nanocomposite Films ◽  
Preliminary Study ◽  
Mechanical Performances

We investigated the efficacy of several nanoclays (halloysite, sepiolite and laponite) as nanofillers for Mater-Bi, which is a commercial bioplastic extensively used within food packaging applications. The preparation of Mater-Bi/nanoclay nanocomposite films was easily achieved by means of the solvent casting method from dichloroethane. The prepared bio-nanocomposites were characterized by dynamic mechanical analysis (DMA) in order to explore the effect of the addition of the nanoclays on the mechanical behavior of the Mater-Bi-based films. Tensile tests found that filling Mater-Bi with halloysite induced the most significant improvement of the mechanical performances under traction force, while DMA measurements under the oscillatory regime showed that the polymer glass transition was not affected by the addition of the nanoclay. The tensile properties of the Mater-Bi/halloysite nanotube (HNT) films were competitive compared to those of traditional petroleum plastics in terms of the elastic modulus and stress at the breaking point. Both the mechanical response to the temperature and the tensile properties make the bio-nanocomposites appropriate for food packaging and smart coating purposes. Here, we report a preliminary study of the development of sustainable hybrid materials that could be employed in numerous industrial and technological applications within materials science and pharmaceutics.

scholarly journals Synthesis, Hydrophilicity and Micellization of Coil–Brush Polystyrene-b-(polyglycidol-g-polyglycidol) Copolymer—Comparison with Linear Polystyrene-b-Polyglycidol

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 253
Author(s):  
Mariusz Gadzinowski ◽  
Maciej Kasprów ◽  
Teresa Basinska ◽  
Stanislaw Slomkowski ◽  
Łukasz Otulakowski ◽  
...  
Keyword(s):  
Contact Angle ◽  
Self Assembly ◽  
Original Method ◽  
Critical Micellization Concentration ◽  
Water Contact ◽  
1H And 13C Nmr ◽  
Similar Composition ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Static Conditions

In this paper, an original method of synthesis of coil–brush amphiphilic polystyrene-b-(polyglycidol-g-polyglycidol) (PS-b-(PGL-g-PGL)) block copolymers was developed. The hypothesis that their hydrophilicity and micellization can be controlled by polyglycidol blocks architecture was verified. The research enabled comparison of behavior in water of PS-b-PGL copolymers and block–brush copolymers PS-b-(PGL-g-PGL) with similar composition. The coil–brush copolymers were composed of PS-b-PGL linear core with average DPn of polystyrene 29 and 13 of polyglycidol blocks. The DPn of polyglycidol side blocks of coil–b–brush copolymers were 2, 7, and 11, respectively. The copolymers were characterized by 1H and 13C NMR, GPC, and FTIR methods. The hydrophilicity of films from the linear and coil–brush copolymers was determined by water contact angle measurements in static conditions. The behavior of coil–brush copolymers in water and their critical micellization concentration (CMC) were determined by UV-VIS using 1,6-diphenylhexa-1,3,5-trien (DPH) as marker and by DLS. The CMC values for brush copolymers were much higher than for linear species with similar PGL content. The results of the copolymer film wettability and the copolymer self-assembly studies were related to fraction of hydrophilic polyglycidol. The CMC for both types of polymers increased exponentially with increasing content of polyglycidol.

Sign in / Sign up

Export Citation Format

Share Document