scholarly journals Effect of adding zinc oxide nanoparticles supported in 4A zeolite on antibacterial properties and flexural strength of self-curing acrylic resin used in removable orthodontic appliances

2021 ◽  
Vol 43 (3) ◽  
pp. 274-282
Author(s):  
Mahdiyeh Esmaeilzadeh ◽  
Baharak Divband ◽  
Fatemeh Yeganeh Sefidan ◽  
Mona Gholami ◽  
Mojgan Kachoei
Keyword(s):  
Flexural Strength ◽  
Antibacterial Properties ◽  
Acrylic Resin ◽  
Test Method ◽  
Bending Test ◽  
Orthodontic Appliances ◽  
X Ray ◽  
Acrylic Resins ◽  
4A Zeolite ◽  
Base Plates

Background: Self-curing acrylic resins, mainly composed of Polymethyl Methacrylate (PMMA), are widely used to manufacture removable orthodontic appliances. Self-curing acrylic resins have higher porosity than heat-curing acrylic resins leading to a susceptible place for microbial plaque colonization. Due to some of these microorganisms' activities, a very unpleasant odor is emitted from orthodontic base plates, which has adverse effects on patients' cooperation. This study aimed to investigate the antimicrobial properties of cold-curing PMMA acrylic resin containing ZnO nanoparticles supported in 4A zeolite and evaluating its mechanical properties. Methods: The synthesized nanocomposite ZnO/4A zeolite was added to SR Triplex® Cold orthodontic self-curing acrylic resin powder with 2wt% and 4wt% concentrations. X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FE-SEM), energy dispersive X-ray (EDX), MAP analysis, and Dynamic light scattering (DLS) were performed to investigate the sample's characteristics. Direct test method was used to assess the antibacterial properties of the fabricated acrylic samples against three bacterial strains Streptococcus mutans, Klebsiella Pnemoniae, and Esherichia coli. Flexural strength was evaluated by a three-point bending test, and One-way ANOVA and Tukey's post hoc test were used for statistical evaluation of data. The p-value of less than 0.05 was considered significant. Results: The addition of ZnO/4A in 2wt% and 4 wt% concentrations lead to more than 99% destruction of colonies in all three types of microorganisms. The mean flexural strength of acrylic specimens containing 2wt% and 4wt% of ZnO/4A significantly lower than the control group. Despite the considerable reduction, all mean values are greater than 50 MPa. Conclusion: The ZnO/4A zeolite nanocomposite due to its potent antibacterial properties and minimal toxicity can reduce the unfavorable odor of orthodontic base plates consequently increases patient cooperation and reaching the desired result. Method: The synthesized nanocomposite ZnO/4A zeolite was added to SR Triplex® Cold orthodontic self-curing acrylic resin powder with 2wt% and 4wt% concentrations. X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy(FE-SEM), energy dispersive X-ray (EDX), MAP analysis, and Dynamic light scattering (DLS) were performed to investigate the sample's characteristics. Direct test method was used to assess the antibacterial properties of the fabricated acrylic samples against three bacterial strains Streptococcus mutans, Klebsiella Pnemoniae, and Esherichia coli. Flexural strength was evaluated by a three-point bending test, and One-way ANOVA and Tukey's post hoc test were used for statistical evaluation of data. The p-value of less than 0.05 was considered significant. Results: The addition of ZnO/4A in 2wt% and 4 wt% concentrations lead to more than 99% destruction of colonies in all three types of microorganisms. The mean flexural strength of acrylic specimens containing 2wt% and 4wt% of ZnO/4A significantly lower than the control group. Despite the considerable reduction, all mean values are greater than 50 MPa. Conclusion: The addition of ZnO/4A zeolite nanocomposite due to its potent antibacterial properties and minimal toxicity can reduce the unfavorable odor of orthodontic base plates consequently increases patient cooperation and reaching the desired result.

scholarly journals Incorporation of Chitosan Nanoparticles into a Cold-Cure Orthodontic Acrylic Resin: Effects on Mechanical Properties

Biomimetics ◽  
2021 ◽  
Vol 6 (1) ◽  
pp. 7
Author(s):  
Mostafa Shahabi ◽  
Sorour Movahedi Fazel ◽  
Abdolrasoul Rangrazi
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Chitosan Nanoparticles ◽  
Antimicrobial Properties ◽  
Acrylic Resin ◽  
Orthodontic Appliances ◽  
Negative Effects ◽  
Acrylic Resins

Improvement of the antibacterial properties of acrylic resins, used in the construction of removable orthodontic appliances, is an important strategy to reduce the incidence of caries and oral diseases in orthodontic treatments. The addition of antimicrobial agents to acrylic resins is one of the effective methods to enhance the antimicrobial properties of these materials. However, one main concern is that modification of acrylic resin has negative effects on its mechanical properties. Recently, chitosan nanoparticles (NPs), as biocompatible and biodegradable polysaccharides with remarkable antimicrobial properties, have been used in different areas of dentistry and medicine. This study aimed to investigate the effects of adding chitosan NPs on the mechanical properties of a cold-cure orthodontic acrylic resin. The chitosan NPs were added to the acrylic resin in various weight percentages: 0% (control), 0.5%, 1%, 2%, and 4%. The flexural strength, compressive strength, Vickers microhardness, and impact strength measurements were performed for all five groups. The results showed that adding up to 1% (w/w) chitosan NPs to an acrylic resin had no significant negative effects on its flexural strength and compressive strength, while it decreased these parameters at weight percentages of 2% and 4% (w/w). The results also revealed that modification of acrylic resin with chitosan NPs up to 4% had no significant negative effects on the microhardness and impact strength of acrylic resin. In conclusion, the addition of chitosan NPs up to 1% (w/w) had no significant negative effects on the mechanical properties of cold-cure acrylic resin.

scholarly journals Evaluation Flexural Strength of PMMA Resins with the Addition of Nanoparticles

2021 ◽  
Author(s):  
Canan Akay ◽  
Duygu Karakis
Keyword(s):  
Flexural Strength ◽  
Acrylic Resin ◽  
Bending Test ◽  
Zro2 Nanoparticles ◽  
Control Group ◽  
Test Machine ◽  
Three Point Bending ◽  
Acrylic Resins ◽  
Heat Cure ◽  
Topographic Characteristics

Abstract The flexural strength of heat cure acrylic resin was investigated by adding different concentrations of TiO2 and ZrO2 nanoparticles to increase its mechanical properties. ZrO2 and TiO2 nanoparticles were added at 1, 3, and 5% concentrations to the powder portion of heat polymerized acrylic resins. A total of 49 samples were prepared in 65 × 10 × 3 mm size. The structural characterisations of all experimental groups were determined by Fourier transform infrared spectroscopy. Flexural strength of the resin specimens was evaluated with a three-point bending test in a universal test machine and then examined under by scanning electron microscope to assess its topographic characteristics. The highest flexural strength value was obtained for 3% TiO2, while the lowest values were obtained for 1% and 5% TiO2. 1% ZrO2 and 3% TiO2 groups showed statistically higher flexural strength values than the control group. Addition of 3% and 5% ZrO2 and 1% and 5% TiO2 showed statistically lower flexural strength than the control group.

scholarly journals Evaluation of flexural strength and antibacterial effect of orthodontic acrylic resins containing Galla chinensis extract

2020 ◽  
Vol 25 (6) ◽  
pp. 43-48
Author(s):  
Shabnam Ajami ◽  
Raha Habibagahi ◽  
Reza Khashei ◽  
Malihe Soroorian
Keyword(s):  
Antimicrobial Activity ◽  
Flexural Strength ◽  
Antibacterial Properties ◽  
Acrylic Resin ◽  
Study Groups ◽  
Herbal Extract ◽  
Control Group ◽  
Orthodontic Appliances ◽  
Disk Diffusion Test ◽  
Significant Difference

ABSTRACT Objective: To evaluate different concentrations of Galla chinensis extract (GCE) added to poly(methyl methacrylate) (PMMA), which is widely used for fabrication of removable orthodontic appliances, regarding the effectiveness of this herbal extract on antimicrobial effect and flexural strength of PMMA. Methods: Acrylic resin samples containing 0.4%, 0.8% and 1.6% GCE were prepared. Flexural strength was investigated via three-point flexural strength test for the 15 acrylic resin blocks of each concentration. Disk diffusion test was used to evaluate antibacterial effects of incorporating the same concentrations of GCE into acrylic resin. All these three groups were compared with the control group, with no added GCE, regarding flexural strength and antibacterial properties. Results: Comparison of flexural strength between the three study groups and the control group showed significant differences between the groups (P=0.018). However, there was no significant difference between the groups containing GCE. There were significant differences in antimicrobial activity between the four groups (P=0.026). Conclusion: Within the limitations of this study, it is suggested that incorporation of GCE into PMMA would be beneficial for antimicrobial activity and flexural strength of PMMA, but further studies on other physical properties and antimicrobial effects on other bacterial strain would be beneficial prior to clinical investigations.

The Effect of Bleach Liquid and Household Cleaner on Surface Hardness and Roughness of Acrylic Base of Orthodontic Appliances

2021 ◽  
Author(s):  
Saeed Noorollahian ◽  
Farinaz Shirban ◽  
Vahid Mojiri
Keyword(s):  
Surface Roughness ◽  
Hydrochloric Acid ◽  
Sodium Hypochlorite ◽  
Surface Hardness ◽  
Acrylic Resin ◽  
Liquid Sodium ◽  
P Value ◽  
Orthodontic Appliances ◽  
Acrylic Resins ◽  
Significant Difference

Introduction: The daily use of orthodontic removable plates can interfere with the self-cleansing function of the mouth. Although various techniques have been proposed for cleaning removable orthodontic appliances, there is no consensus on the use of a safe method that preserves the physical properties of the appliance. This study aimed to investigate the effect of using hydrochloric acid (10%, for removal of mineral deposits) and sodium hypochlorite (5.25%, to remove organic matter and discolorations) on surface hardness and roughness of self-cure orthodontic acrylic resins. Materials & Methods: This cross-sectional laboratory study was conducted in the fall of 2017 at Isfahan University of Medical science and Isfahan University of Technology. In this study two orthodontic acrylic resins (Orthocryl® and Acropars®) were used. Eighty samples (12×10×3 mm) from each one were fabricated and divided into four groups (n = 20). Group 1: 15 minutes immersion in household cleaner liquid (Hydrochloric acid, 10%) followed by15 minutes immersion in household bleach liquid (Sodium Hypochlorite, 5.25%). In group 2, immersions were repeated just like group two times and in group 3, were done three times. Group 4 was as control and had no immersion. The surface hardness and roughness of samples were measured. Data were analyzed with Two Way ANOVA and the significance level was set at 0.05. Results: The number of immersion procedures did not significantly affect the surface hardness (p value = 0.958) and surface roughness (p value = 0.657) in the different study groups. There was no significant difference in the surface hardness between the two acrylic resin brands (p value = 0.077); however, Acropars acrylic resin samples exhibited significantly higher surface roughness compared to the Orthocryl acrylic resin samples(p value < 0.001). Conclusion: 15 minutes of immersion in 10% HCl, followed by 15 minutes of immersion in 5.25% NaOCl and repetition of the procedure three times did not significantly affect the surface hardness and roughness of self-cured acrylic resins.

scholarly journals Surface morphology changes of acrylic resins during finishing and polishing phases

2013 ◽  
Vol 18 (6) ◽  
pp. 26-30 ◽  
Author(s):  
Glaucio Serra ◽  
Liliane Siqueira de Morais ◽  
Carlos Nelson Elias
Keyword(s):  
Surface Morphology ◽  
Acrylic Resin ◽  
Surface Finishing ◽  
Control Group ◽  
Orthodontic Appliances ◽  
Test Results ◽  
Good Surface ◽  
Acrylic Resins ◽  
Polishing Procedures ◽  
Removable Orthodontic Appliances

INTRODUCTION: The finishing and polishing phases are essential to improve smoothness and shining on the surface of acrylic resins used to make removable orthodontic appliances. A good surface finishing reduces roughness, which facilitates hygiene, prevents staining and provides greater comfort to the patients. OBJECTIVE: The aim of this paper was to analyze the changes on surface morphology of acrylic resins during finishing and polishing phases. METHODS: Thirty discs (10 mm in diameter and 5 mm in length) were made with acrylic resin and randomly divided into ten groups. The control group did not receive any treatment while the other groups received gradual finishing and polishing. The last group received the entire finishing and polishing procedures. Surface morphology was qualitatively analyzed through scanning electron microscopy and quantitatively analyzed through a laser profilometer test. RESULTS: The acrylic resin surfaces without treatment showed bubbles which were not observed in the subsequent phases. Wearing out with multilaminated burs, finishing with wood sandpaper and finishing with water sandpaper resulted in surfaces with decreasing irregularities. The surfaces that were polished with pumice and with low abrasive liquids showed high superficial smoothness. CONCLUSION: Highly smooth acrylic resin surfaces can be obtained after mechanical finishing and polishing performed with multilaminated burs, wood sandpaper, water sandpaper, pumice and low abrasive liquids.

scholarly journals Effect of microwave disinfection on physical and mechanical properties of acrylic resins

2008 ◽  
Vol 19 (4) ◽  
pp. 348-353 ◽  
Author(s):  
Rafael Leonardo Xediek Consant ◽  
Erica Brenoe Vieira ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
João Neudenir Arioli-Filho
Keyword(s):  
Flexural Strength ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Hardness Test ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Acrylic Resins ◽  
Strength Tests ◽  
The Impact

This study evaluated the effect of microwave energy on the hardness, impact strength and flexural strength of the Clássico, Onda-Cryl and QC-20 acrylic resins. Aluminum die were embedded in metallic or plastic flasks with type III dental stone, in accordance with the traditional packing technique. A mixing powder/liquid ratio was used according to the manufacturer's instructions. After polymerization in water batch at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling at room temperature, and submitted to finishing. Specimens non-disinfected and disinfected by microwave irradiation were submitted to hardness, impact and flexural strength tests. Each specimen was immersed in distilled water and disinfected in a microwave oven calibrated to 650 W for 3 min. Knoop hardness test was performed with 25 g load for 10 s, impact test was carried out using the Charpy system with 40 kpcm, and 3-point bending test with a crosshead speed of 0.5 mm/min until fracture. Data were submitted to statistical analysis by ANOVA and Tukey's test (?=0.05). Disinfection by microwave energy decreased the hardness of Clássico and Onda-Cryl acrylic resins, but no effect was observed on the impact and flexural strength of all tested resins.

scholarly journals A Comparative Evaluation of Flexural Strength of Commercially Available Acrylic and Modified Polymethylmethacrylate: An in vitro Study

2013 ◽  
Vol 14 (1) ◽  
pp. 80-83 ◽  
Author(s):  
Naveen S Yadav ◽  
Teerthesh Jain ◽  
Amrita Pandita ◽  
SMA Feroz ◽  
UK Kartika ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Methacrylic Acid ◽  
Comparative Evaluation ◽  
Testing Machine ◽  
Acrylic Resin ◽  
Bending Test ◽  
Control Group ◽  
Diabetic Patients ◽  
Denture Stomatitis

ABSTRACT Aim The purpose of this study was to evaluate and compare the flexural strength of commercially available acrylic (trevalone) and modified polymethylmethacrylate (PMMA). Materials and methods Four groups were tested; Group 1— control group regular MMA, group 2—2% methacrylic acid, 88% MMA, group 3—16% methacrylic acid, 84% MMA group 4— 20% methacrylic acid, 80% MMA 15 resin specimens of each group were polymerized. After processing, the specimens were subjected for flexural strength testing using three point bending test in a Universal Testing Machine. All data was statistically analyzed with one-way ANOVA, differences within the groups were analyzed by Scheffe's analysis. Results As the ratio of incorporated methacrylic acid to PMMA increased, the flexural strength decreased. Analysis of data revealed a significant decrease in flexural strength of specimens (p < 0.000) after incorporation of 12%, 16%, 20% methacrylic acid to heat polymerized acrylic resin, when compared with the control group. Lowest flexural strength was observed with specimens containing 20% methacrylic acid and highest flexural strength was observed with specimens containing conventional monomer without methacrylic acid. Conclusion It was observed that as the concentration of methacrylic acid in heat polymerized acrylic resin increases, the flexural strength decreases. Lowest flexural strength was observed with specimens containing 20% methacrylic acid and highest flexural strength was observed with specimens containing conventional monomer without methacrylic acid. Clinical significance The major advantages of addition of methacrylic acid to polymethylmethacrylate could be for the elderly people with restricted manual dexterity or cognitive disturbances, especially for patients who do not follow an adequate denture cleansing protocol and diabetic patients who are more susceptible for denture stomatitis. How to cite this article Jain T, Yadav NS, Pandita A, Feroz SMA, Kartika UK, Singh PP. A Comparative Evaluation of Flexural Strength of Commercially Available Acrylic and Modified Polymethylmethacrylate: An in vitro Study. J Contemp Dent Pract 2013;14(1):80-83.

scholarly journals Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

2009 ◽  
Vol 20 (2) ◽  
pp. 132-137 ◽  
Author(s):  
Rafael Leonardo Xediek Consani ◽  
Douglas Duenhas de Azevedo ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
Paulo César Saquy
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Denture Base ◽  
Acrylic Resins ◽  
The Impact

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

scholarly journals Antimicrobial properties, anti-virulence activities, and physico-mechanical characteristics of orthodontic adhesive containing C-phycocyanin: a promising application of natural products

Folia Medica ◽  
2021 ◽  
Vol 63 (1) ◽  
pp. 113-121
Author(s):  
Maryam Pourhajibagher ◽  
Abbas Bahador
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Antimicrobial Properties ◽  
Acrylic Resin ◽  
Inhibition Zone ◽  
Antimicrobial Activities ◽  
Microbial Biofilms ◽  
Growth Inhibition Zone ◽  
Orthodontic Adhesives ◽  
Acrylic Resins

Introduction: Antimicrobial orthodontic adhesives aim to reduce enamel demineralization, white spot lesions, and incipient tooth decay around bonded orthodontic brackets, but they should not imperil its mechanical properties.&nbsp; Aim: To evaluate the antimicrobial and physico-mechanical properties of acrylic containing different concentrations of C-phycocyanin on Streptococcus mutans, Lactobacillus acidophilus, and Candida albicans. Materials and methods: The mechanical properties of acrylic resins were measured by flexural strength test after preparation of acrylic resin samples with concentrations of 1%, 2%, 5%, 7.5%, and 10% of C-phycocyanin. Then we evaluated the antimicrobial effects of acrylic resin containing the maximum concentration of C-phycocyanin with clinically acceptable flexural strength and the changes in expression of virulence factors. Results: The highest and lowest means of flexural strength were obtained in acrylic resins containing 0% and 10% concentrations of C-phycocyanin at 50.2&plusmn;4.5 and 30.1&plusmn;3.3 MPa, respectively. Adding 1%, 2%, and 5% of C-phycocyanin showed no significant decrease in flexural strength (p>0.05). The maximum mean diameter of the growth inhibition zone was observed around discs containing 5% of C-phycocyanin. Until day 30 of the study, no microbial biofilms were formed on any acrylic disc. Only microbial biofilms of C. albicans were able to form on discs containing 5% of C-phycocyanin at 90 days. 5% C-phycocyanin could significantly decrease the expression levels of gtfB, hsp16, and ALS9 6.1-, 7.3-, and 3.9-fold, respectively. Conclusions: It can be concluded that the most acceptable concentration of C-phycocyanin in acrylic resin is 5% based on the results of flexural strength tests and antimicrobial activities of acrylic resin containing various concentrations of C-phycocyanin.

Sign in / Sign up

Export Citation Format

Share Document