scholarly journals Data Communication Security Issues of Wi-Fi over Li-Fi

2019 ◽  
Vol 8 (3) ◽  
pp. 1977-1981

Visible Light Communications (VLC) system is called Light Fidelity One such example, analog data is passed to a LED (Light-Emitting Diode) bulb (using signal processing technology), after that it transmits data (which is implanted in its beam) to the detector or photodiode. The small commutes in the brisk feeble of LED bulbs is modulated by the receiver circuit into electrical signal. The signal is then reversed into a duplex data runnel that could be recognized in the same way that of audio, video and web programs that run on devices that has internet enabled. Wi-Fi is vulnerable to breaches involving various security issues such as Rouge Access Points, Denial of Service, Wireless Trespasser, Data Interruption, End point attacks etc. To overcome such restrictions, this paper proposes application level substructure for data communication using Li-Fi (Light Fidelity) Technology. By using LED lights as a transmission medium, the indoor wireless communication is achieved in much faster rate than the one WiFi (Wireless Fidelity) can provide.

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Ritvik Shukla ◽  
Salini Bose ◽  
Shubham Shukla ◽  
Kamal Kishor Upadhyay ◽  
Nikhlesh Kumar Mishra ◽  
...  

AbstractIn the current era of data communication everyone deals with the huge amount of data in form of text, audio, video and different other formats in which everyone want a secure and higher bandwidth channel to transmit and receive so, only the optical channel provides the solution of above said problem. The only difficulty with the existing model that the data from electrical domain first converted in form of light (optical domain) at the transmission end while after receiving the data at the receiver end it will be further converted in form of electrical signal for extracting the message. This type of conversion from one domain to other gives the energy loss. In the current research article, we proposed a model of optical processor which transmit and receive the data without conversion which provides an energy efficient optical technology. By adding reversibility, heat bender can be further reduced. In this manuscript, an arithmetical logic unit has been created, a photonic reversible complete subtractor and an irregular logic portal. SOA-MZI structure is the basic component of the architecture. The method is mainly carried out by the semiconductor Amplifier, using nonlinear properties such as cross-gain modulation and cross-phase modulation. The efficiency deciding factor for the whole system is 21.23 and 53.27 dB in the average extinction ratio. The cost of the arithmetic logic unit optically constructed is 9.


2019 ◽  
Vol 629 ◽  
pp. A27 ◽  
Author(s):  
A. Coffinet ◽  
C. Lovis ◽  
X. Dumusque ◽  
F. Pepe

Context. Doppler spectroscopy has been used in astronomy for more than 150 yr. In particular, it has permitted us to detect hundreds of exoplanets over the past 20 yr, and the goal today of detecting Earth-like planets requires a precision around 0.1 m s−1 or better. Doppler spectroscopy has also been and will be of major importance for other studies such as the variability of fundamental constants and cosmological studies. For all these applications, it is crucial to have the best possible wavelength calibration. Despite the fact that the HARPS spectrograph has been operational at the 3.6-m ESO telescope for more than 15 yr, and that it provides among the most precise Doppler measurements, improvements are still possible. One known problem, for instance, is the non-fully regular block-stitching of the charge-coupled devices (CCDs), which in some cases introduces one-year period parasitic signals in the measured radial velocity. Aims. The aim of the presented work is to improve the wavelength calibration of the HARPS spectrograph to push further its planet-detection capabilities. Methods. The properties of the CCD stitching-induced pixel-size anomalies were determined with light-emitting-diode (LED) flat-field frames, and then a physical, gap-corrected map of the CCDs is used for the fitting model of the spectral orders. We also used a new thorium line list, based on much higher-accuracy measurements than the one used up to now. We derive new wavelength solutions for the 15 yr of HARPS data, both before and after the fibre upgrade that took place in 2015. Results. We demonstrate that we do indeed correct the gap anomalies by computing the wavelength solutions of laser frequency comb exposures, known to have a very low dispersion, both with and without taking the gap correction into account. By comparing the rms of the most stable stars of the HARPS sample, we show that we globally decrease the radial velocity (RV) dispersion of the data, especially for the data acquired after the change of fibres of 2015. Finally, the comparative analysis of several individual systems shows that we manage to attenuate the periodogram power at one year in most cases. The analysis of the RVs derived from individual stellar lines also shows that we indeed correct the stitching-induced RV variation. Conclusions. This improved calibration of the HARPS spectrograph allows to go deeper in the search for low-amplitude radial-velocity signals. This new calibration process will be further improved by combining the thorium calibration spectra with laser frequency comb and Fabry–Perot calibration spectra, and this will not only be used for HARPS but notably also for HARPS-N and the new ESPRESSO spectrograph.


Author(s):  
Dominic O'Brien ◽  
Sujan Rajbhandari ◽  
Hyunchae Chun

Providing a reliable link, with sufficient signal-to-noise ratio (SNR) and bandwidth to deliver high-capacity communications is a critical challenge for optical wireless (OW) communications and understanding and jointly optimizing the performance of the transmitter and receiver subsystems is a key part of this. At the transmitter a source of light, either a laser or a light-emitting diode, must be modulated with the communications signal. The resulting emission must be directed, using optics or steering systems, as required for the particular application, and must be within any safety levels set by relevant standards. The receiver is the most critical part of any optical link, as its design is a dominant factor in determining the received SNR, which determines the capacity and ultimately the utility of the link. A receiver must collect, filter and concentrate signal radiation, then detect and amplify the resulting electrical signal. This review surveys the state-of–the-art transmitter and receiver technologies. Details of design constraints are discussed, and potential future directions discussed. This article is part of the theme issue ‘Optical wireless communication’.


Plants ◽  
2020 ◽  
Vol 9 (10) ◽  
pp. 1351
Author(s):  
Chia-Chen Chen ◽  
Maw-Rong Lee ◽  
Chi-Rei Wu ◽  
Hsin-Ju Ke ◽  
Hui-Min Xie ◽  
...  

Investigations were carried out to study the effects of light-emitting diode (LED) lights on growth and development of isosteroidal alkaloids in embryogenic calli of Fritillaria cirrhosa D. Don, an important traditional Chinese medicine herb. Calli were cultured in glass bottles, each containing 100 mL of Murashige and Skoog’s basal medium supplemented with 2% sucrose and 0.4% gellan gum powder, a gelling agent. These bottles were incubated in a specially designed plant growth chamber equipped with eight different LED lights consisting of single or combinations of four different light spectra emitting blue (450 nm), green (525 nm), red (660 nm), and far-red (730 nm) light. After three months of incubation, morphological changes in embryogenic calli were recorded, and LC-MS/MS analysis of cultures was carried out for peimisine, sipeimine, peiminine, and peimine. The highest number of somatic embryos and the maximum fresh weight was recorded in calli incubated under red (9R), infrared (9IR), and a combination of red+blue+infrared (3R3B3IR), respectively, in decreasing order. The highest contents of peimisine, peiminine, and peimine were recorded under red (9R) and infrared (9IR) lights, respectively. Eight LED lights had significant effects on the morphogenesis of embryogenic calli of F. cirrhosa D. Don and contents of isosteroidal alkaloids.


2020 ◽  
Vol 3 (1) ◽  
pp. 12
Author(s):  
Noah de Castro ◽  
Robin Lewis Cooper

Monitoring movements of larval Drosophila with electrical detection allows one to record the behaviors without the use of lights and cameras. This is a suitable technique when studying the use of light-sensitive proteins in optogenetic studies. Electrical measures are feasible to use in determining when a larva starts to move or continues to move after a light induced activation of channelrhodopsin. We have developed a technique using an electrical measure of the media as an index of larval movement. As a proof of concept, recordings with an infrared camera of the larval movement were simultaneous made with electrical measures. The two techniques parallel each other in their ability to index larval movements. Bright light-emitting diode (LED) lights used in optogenetic experiments tend to saturate the detectors of the camera unless filters are used and different filters maybe necessary depending on the LED spectrum and sensitivity of the camera. Impedance measures are independent of the type of LED or brightness. We also assessed the use of a non-solvent based glue (3M Vetbond) to hold larvae in place while measuring synaptic function of neuromuscular junctions, cardiac function and influence of modulators, or activation of light-sensitive channels.


2017 ◽  
Vol 50 (6) ◽  
pp. 921-936 ◽  
Author(s):  
WJ Huang ◽  
Y Yang ◽  
M Ronnier Luo

This paper describes an experiment to investigate discomfort glare caused by white light-emitting diode (LED) lights having different spectral power distributions. It included two groups: a ‘Metamerism’ group and a ‘correlated colour temperatures (CCT)’ group. In the former group, it was found that white lights at 7000 K constructed from different blue LEDs and the same red and green LEDs gave about the same glare perception. In the latter group, there was a significant difference in glare perception between white lights having different CCTs. Finally, glare models, including unified glare rating (UGR) and the newly derived QUGRspd, and mUGRspd models, were tested using the data from the experiment. All of them gave quite accurate predictions of the data.


Author(s):  
Kil-Nam Kim ◽  
Hye-Sung Song ◽  
Ryong-Jin Choe ◽  
Zhi-Juan Huang ◽  
Qiu-Ying Huang ◽  
...  

Recently, light traps using light-emitting diode (LED) lights have been applied to monitor or control insect pests. The oriental armyworm, Mythimna separata Walker, is an important insect pest that has caused damage to several cereal crops, including corn, wheat and rice. The present study aims to seek out a sensitive wavelength causing high phototactic response in M. separata. The study evaluated the phototactic responses of M. separata moths to several LED lights of different wavelengths and luminance intensities under laboratory condition. Results showed that green (520 nm) LED light resulted in significant phototactic response of M. separata moths compared to LED lights of other wavelengths. Additionally, the highest attraction rate of the moths to green LED light appeared in luminance intensity group of 200 lux compared to the other intensities groups. Experiments under optimum conditions based on the above experiments revealed that the green LED light exhibited the strongest attraction rate (64.44%) among all experimental groups. An experiment performed in a net cage also showed that green LED light resulted in the highest phototactic response of M. separata moths, 1.7 times more than a commercial black light used as control. These findings clearly demonstrate that M. separata moths have a high sensitivity to the green LED light. Therefore, a light trap equipped with green LED light could be useful for monitoring and controlling M. separata moths.


2021 ◽  
Vol 40 (1) ◽  
Author(s):  
Emerson Roberto Santos ◽  
Hélio Akira Furuya ◽  
Elvo Calixto Burini Junior

In this study, optical and lifetime analyses of commercial light-emitting diode (LED) lamps were carried out with the objective to better understand these characteristics. Lamps of different manufacturers and powers were used: Ourolux of 9 watts, Kian of 9 watts, Black+Decker of 9 watts, FLC of 8 watts, Galaxy of 7 watts and Brilia of 7 watts. These LED lamps remained on by 24 hours/day for 4,291.16 hours. Illuminance measurements were analyzed once a week by each lamp inside the integrating sphere with a sensor of lux meter coupled. Results showed decrease of illuminance by elapsed time, due to the degradation. Results of the illuminance obtained between the initial moment of the experiment and the final one were calculated, revealing degradation of 19% to Ourolux, 20% to FLC, 26% to Black+Decker, 28% to Kian, 29% to Galaxy and 33% to Brilia. This study suggests that the diffusers can have different transmittance values interfering on the illuminance, since the FLC LED lamp presented illuminance with highest values than the other LED lamps tested with similar electrical and optical characteristics. This experiment showed that the nominal power of the LED lamp has no direct relation to the illuminance and, comparing the lifetime, the LED lamp manufactured by Black+Decker was the only one to reach 5,521 hours, that is a lifetime much shorter than the one described at the packages (25,000 hours) for all LED lamps tested


2018 ◽  
Vol 4 (2) ◽  
pp. 52
Author(s):  
Anwar Mujadin ◽  
Suci Rahmatia

<p><em>Abstrak – </em><strong>Joule-Thief adalah salah satu rangkaian listrik  untuk konservasi  energi dengan menggunakan teknis medan elektromagnetik arus transien pada sebuah coil. Sirkuit ini dioperasikan menggunakan  sebuah MOSFET sebagai saklar untuk meregenerasi  tegangan dan arus listrik dalam satuan waktu kemudian disalurkan pada beban light emitting diode (LED). Dari hasil eksperimental,  sel volta berbasis air laut dengan tegangan jepit 0.8V mampu mengaktifkan lampu LED dengan konfigurasi rangkaian serial. Hasilnya menunjukkan bahwa power transfer maksimum dari sirkuit Joule-thief sangat efektif sebagai pemasok daya beban 60 LED.</strong></p><p><strong> </strong></p><p><strong><em>Kata Kunci </em></strong><em>- <strong> </strong>Joule Thief, Boost Converter Daya LED, Sel Volta Berbasis Air Laut<strong></strong></em></p><p><em> </em></p><p><em>Abstract –</em> <strong>Joule-Thief is one of the electric circuits for conservation energy by using electromagnetic field trancient current in a coil. This circuit is operated using a MOSFET as a switch to regenerating the voltage and current flowing along the coil. The electric current accumulates in the coil then in unity of time will be supplied to the light emitting diode (LED) load. From experimental results, water sea voltaic cells based with 0.8V clamp voltage are able to activate LED lights in serial circuit configurations. The results shown that power transfer joule-thief circuit is very effective capable of supplying LED up to 60 LEDs.</strong></p><p><strong> </strong></p><p><strong><em>Keywords </em></strong><em>- Joule Thief, </em><em>Boost Converter Power LED</em><em>, </em><em>Sea-Based Voltaic Cells</em><em></em></p>


Author(s):  
Prof. Bhushan Thakre, Dr. R.M Thakre

A novel highly dimmable current controller which is a linear one is employed in the application of low power automotive is discussed here. Light Emitting Diode is the one which drives current that is linearly controlled to decrease the intensity of LED to limit the destruction of the LED and improve its reliability. Although many dimming techniques for LED lighting are available, our proposed method outperforms the existing methods in terms of power consumption and the no. of transistors used in the proposed design. This emits 100mA and decrease the LED current which is going linearly based on the theory of dimming control voltage. Toggling of LED is avoided finally in comparison with the existing system. This circuit is developed in 0.18μm process technology and Cadence ADE with Spectre is employed for simulation purpose. The proposed method utilizes a maximum power of 392.85 mW when the supply voltage is 4V and the control voltage is 4V at the temperature of 27oC.


Sign in / Sign up

Export Citation Format

Share Document