scholarly journals Mechanical Properties of Fly Ash Polymer Concrete with Different Fibers

2018 ◽  
Vol 55 (3) ◽  
pp. 405-409 ◽  
Author(s):  
Marinela Barbuta ◽  
Alexandru Timu ◽  
Liliana Bejan ◽  
Roxana Dana Bucur
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Polymer Concrete ◽  
Test Results ◽  
Material Industry ◽  
Split Tensile Strength ◽  
Building Material Industry ◽  
Concrete Properties ◽  
Different Types ◽  
General Demand

The experimental results obtained by studying the influence of different types of fibers on the mechanical properties of fly ash polymer concrete are presented in the paper. The general demand of using wastes found applicability in building material industry because some of them are beneficial in improving concrete properties. The waste additions type fly ash and fibers were incorporated in polymer concrete. The study focused on fibers type glass, polyester, metallic and cellulose. The mechanical properties such as compressive strength, flexural strength and split tensile strength were investigated having in view the type, dosage and length of fibers. The results show that fibers improved mechanical properties in comparison with that of polymer concrete without fibers, the test results being differently influenced by the factors which were considered.

scholarly journals Determination of Mechanical Properties of Rubberized Concrete in Marine Environment

2019 ◽  
Vol 8 (2) ◽  
pp. 5761-5765
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Marine Environment ◽  
Concrete Specimen ◽  
Crumb Rubber ◽  
Fine Aggregate ◽  
Test Results ◽  
Rubberized Concrete ◽  
Split Tensile Strength

With an objective of saving the environment by providing crumb rubber as an alternative to natural fine aggregate this paper presents a study carried out to find the mechanical properties of rubberized concrete. Rubberized concrete is made up of waste rubber from vehicle tyres and other rubber waste which otherwise is left out polluting the environment. In this paper, 7.5% of crumb rubber (obtained by shredding the vehicle tyres) as an alternative to fine aggregate and 7.5% of fly-ash as an alternative to cement is added with other ingredients of concrete to produce an eco-friendly concrete which can be used economically and effectively for construction along the coastal areas. Various properties like workability, compressive strength, split tensile strength, and flexural strength was carried out on concrete specimens exposed to the natural marine environment along the coast of Visakhapatnam, Andhra Pradesh. The total exposure of concrete specimen was about 150 days, and various specimens were tested at 7, 28, 90, 120 and 150 days, respectively. The test results showed that with a slight compromise in strength, the workability of concrete and resistance to the effect of seawater on the strength of concrete significantly improved with the addition of crumb rubber and fly-ash.

scholarly journals The Effect of Accelerators and Mix Constituents on the High Early Strength Concrete Properties

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
V. M. Sounthararajan ◽  
A. Sivakumar
Keyword(s):  
Fly Ash ◽  
Research Study ◽  
High Strength ◽  
Dosage Level ◽  
Test Results ◽  
Strength Gain ◽  
Strength Concrete ◽  
Concrete Properties ◽  
Different Types ◽  
Early Strength

The present research study focused on the high early strength concrete properties that can be produced with large replacement of cement by fly ash. Also, the effects of adding fibres on the compressive strength gain and early age strength gain properties are determined. Tests were conducted on different high strength concrete specimens, where fly ash was substituted for cement up to 50%. Different types of concrete specimens were casted and tested for different fine-to-coarse aggregate ratio, metallic fibre content, cement-to-total-aggregate ratio, and accelerator dosage. The test results indicated that high early strength concrete (50.7 MPa at 7 days) was obtained for higher F/C ratio of 0.8, C/TA ratio of 0.24, and higher dosage level of steel fibre at 1.5%.

Durability of Red Mud Based Geopolymer Paste in Acid Solutions

2016 ◽  
Vol 866 ◽  
pp. 99-105 ◽  
Author(s):  
Smita Singh ◽  
M.U. Aswath ◽  
R.V. Ranganath
Keyword(s):  
Mechanical Properties ◽  
Acetic Acid ◽  
Fly Ash ◽  
Red Mud ◽  
Acetic Acid Solution ◽  
Strength Loss ◽  
Acid Solutions ◽  
Test Results ◽  
Acid Attack ◽  
Geopolymer Paste

The present investigation is on the effect of red mud on the mechanical properties and durability of the geopolymer paste in sulphuric and acetic acid solution. Red mud and fly ash were used to form the geopolymer paste along with the alkalies. The variation of red mud in the paste composition was from 0% to 90%. Cylindrical shaped specimens of 1 inch diameter and 1 inch height were prepared. The specimens were immersed in 5% sulphuric acid and 5% acetic acid for 1, 7, 14, 28, 56 and 84 days and tested for weight loss, visual deformation, strength loss and colour of the solvent, based on the procedure specified by ASTM C 267 – 01. SEM/EDX Tests were performed on the geopolymer specimens. Test results show that initially, the strength of the geopolymer increased upon the addition of red mud. The strength was maximum when the percentage of red mud was 30%. The maximum strength obtained was 38 MPa for the paste containing 30% red mud using 10M alkali solution as against 31.69 MPa, when only fly ash was used. Geopolymer paste containing 30% and 50% red mud showed better resistance to acid attack. The strength loss was minimum for the samples containing 30% red mud in both inorganic and organic acid i.e. sulphuric and acetic acid.

Resistance of Polymer Dispersion Additive Modified Concrete to Light Liquids Action

2014 ◽  
Vol 941-944 ◽  
pp. 730-733 ◽  
Author(s):  
Maciej Gruszczyński
Keyword(s):  
Concrete Strength ◽  
Polymer Concrete ◽  
Material Structure ◽  
Reinforced Concrete Structures ◽  
Polymer Dispersion ◽  
Petrol Station ◽  
Concrete Properties ◽  
Different Types ◽  
The Subject ◽  
Styrene Butadiene

Numerous concrete and reinforced concrete structures (industrial floors, petrol station or manoeuvring park pavements, elements of sewage system) are subjected to danger of permanent or periodical action of petroleum liquids that often causes the considerable reduction in concrete strength as well as decrease of bond between concrete and steel, which usually results in structure damages. The subject of the paper is estimation of influence of polymer dispersion additive (styrene-acrylic co-polymer and styrene-butadiene latex) onto durability of concrete subjected to action of different types of light liquids. The influence of polymer dispersion additive was confronted with the action of silica fume usually applied for sealing the structure of concrete. In the paper there are presented tests results for different types of light liquids onto such cement-polymer concrete properties as: strength, penetration depth of light liquids into material structure.

scholarly journals Research on the Dynamic Mechanical Properties and Energy Dissipation of Expansive Soil Stabilized by Fly Ash and Lime

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Sheng-quan Zhou ◽  
Da-wei Zhou ◽  
Yong-fei Zhang ◽  
Wei-jian Wang ◽  
Dongwei Li
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Expansive Soil ◽  
Dynamic Mechanical Properties ◽  
Test Results ◽  
Absorbed Energy ◽  
Dynamic Mechanical ◽  
Stabilized Soil ◽  
Dynamic Compressive Strength

To probe into the dynamic mechanical properties of expansive soil stabilized by fly ash and lime under impact load, the split-Hopkinson pressure bar (SHPB) test was carried out in this study. An analysis was made on the dynamic mechanical property and final fracture morphology of stabilized soil, and the failure mechanism was also explored from the perspective of energy dissipation. According to the test results, under the impact pressure of 0.2 MPa, plain soil and pure fly ash-stabilized soil exhibit strong plasticity. After the addition of lime, the stabilized soil shows obvious brittle failure. The dynamic compressive strength and absorbed energy of stabilized soil first increase and then decrease with the change of mix proportions. Both the dynamic compressive strength and the absorbed energy reach the peak value at the content of 20% fly ash and 5% lime (20% F + 5% L). In the process of the test, most of the incident energy is reflected back to the incident bar. The absorbed energy of stabilized soil increases linearly with the rise of dynamic compressive strength, while the absorbed energy is negatively correlated with the fractal dimension. The fractal dimension of pore morphology of the plain soil is lower than that of the fly ash-lime combined stabilized soil when it comes to the two different magnification ratios. The test results indicate that the modifier content of 20% F + 5% L can significantly improve the dynamic mechanical properties of the expansive soil.

POLYESTER GROUT INCORPORATING FLY ASH AS POTENTIAL INFILL MATERIAL FOR GROUTED CONNECTIONS

2015 ◽  
Vol 77 (12) ◽  
Author(s):  
Nuria S. Mohammed ◽  
Ahmad Baharuddin Abdul Rahman ◽  
Nur Hafizah A. Khalid
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Polyester Resin ◽  
Precast Concrete ◽  
Polymer Binder ◽  
Test Results ◽  
Polymer Additive ◽  
Direct Tension ◽  
And Performance ◽  
Infill Material

This paper presents the mechanical properties and performance of polyester grout as infill material for grouted connection in precast concrete. The mix proportions of polyester grout was properly designed and manufactured. The polymer binder with polymer additive was added together with filing materials of sand and fly ash. The binder to filler ratio was 0.43. Properties such as flowing ability and compression strength were studied by varying the level of fly ash in the mixtures. Also, to assess the efficacy of polyester grouted connections, three grouted connections were tested in direct tension. The test results show that, polyester resin grout with binder to filler ratio 0.43% and 16% fly ash perform satisfactorily. The polyester grout is suitable for use in the steel pipe splice connections.

Experimental Study on the Engineering Characteristics of Improved Soil

2010 ◽  
Vol 168-170 ◽  
pp. 1426-1431
Author(s):  
Zhi Qing Li ◽  
Zhen Dong Cui ◽  
Yan Ping Wang ◽  
Li Chao Wang ◽  
Duo Zhong
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Fly Ash ◽  
Physical And Mechanical Properties ◽  
Hybrid Structure ◽  
Strength Characteristics ◽  
Shanxi Province ◽  
Hydration Reaction ◽  
Test Results ◽  
Shearing Strength

According to the typical loess in Shuozhou in Shanxi province, tests involved in compaction characteristics, shearing strength characteristics and disintegration are carried out by using loess and three kinds of improved loess, namely lime and fly-ash, lime and cement, cement and fly-ash. The best improved soil method is selected. The test results indicate that the compact hybrid structure is formed by fly ash and loess. The activity of fly ash is activated as a result of the lime mixing. A series of hydration reaction prompt the intensity of modified loess. And the physical and mechanical properties of improved loess are improved noticeably.

FLEXURAL BEHAVIOR OF HIGH STRENGTH GEO-POLYMER CONCRETE BEAMS

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Vankudothu Bhikshma ◽  
Kandiraju Promodkumar ◽  
Putta Panduranghiah
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Research Work ◽  
High Strength ◽  
Experimental Results ◽  
Flexural Behavior ◽  
Polymer Concrete ◽  
Conventional Concrete ◽  
Granulated Blast Furnace Slag ◽  
Load Carrying

The demand for concrete is increasing day by day. As the consumption of cement is increased, environmental issues arise due to the release of CO2 during the manufacturing of cement. The objective of this research work is to produce a pollution free concrete with a combination of fly ash and GGBS (Ground granulated blast furnace slag) and without the use of cement. In this paper an attempt was made to study the mechanical properties of high strength geo-polymer concrete of grade M60 using GGBS, fly ash and micro silica. The testing program was planned for the mechanical properties of geo-polymer concrete and flexural behavior of corresponding beams. The experimental results indicated that the geo-polymer concrete M60 grade has a compressive strength of 70.45 MPa at the age of 28 days cured at ambient condition. Further, flexural strength and split tensile strengths for M60 grade high strength geo-polymer concrete at 28 days were observed to be 5.45 MPa and 3.63 MPa respectively. The modulus of elasticity was higher than the theoretical value proposed by IS 456-2000. It was also observed that the load carrying capacity of M60 grade high strength geo-polymer concrete found to be more than corresponding grade conventional concrete. The load-deflection, moment-curvature relationships were studied. The experimental results were encouraging to continue for further research in the area high strength geo-polymer concrete.

scholarly journals Impact of fibre incorporation and compaction method on properties of pervious concrete

2021 ◽  
Vol 71 (342) ◽  
pp. e245
Author(s):  
S. Juradin ◽  
I. Netinger-Grubeša ◽  
S. Mrakovčić ◽  
D. Jozić
Keyword(s):  
Mechanical Properties ◽  
Short Duration ◽  
Pervious Concrete ◽  
Cement Matrix ◽  
Viscous Layer ◽  
Concrete Properties ◽  
Different Types ◽  
Porosity And Permeability ◽  
Positive Effect ◽  
Compaction Method

This paper deals with the possibility of the improvement of pervious concrete properties by incorporation of different types of fibres and studies the effect of short duration vibration of pervious concrete properties in comparison with compaction with wooden lath and hammer. Ten mixtures of pervious concrete were prepared, five of which were compacted with wooden lath and hammer and five by short duration vibration. Density, porosity, permeability and mechanical properties were tested for in hardened pervious concrete specimens. It was concluded that mixtures compacted by short duration vibration had better mechanical properties due to the formation of a viscous layer at the contact surface between the aggregate grain and the cement matrix during the compaction, as well as pore-related properties. The addition of fibres negatively affected porosity and permeability but generally improved mechanical properties of concrete. The positive effect of fibre addition was more emphasised in cases of vibrated mixtures.

scholarly journals IMPACT OF USING STONE POWDER AND MINERAL ADMIXTURES IN HIGH STRENGTH CONCRETE

2020 ◽  
Vol 4 (5) ◽  
pp. 82-87
Author(s):  
Afzal Basha Syed ◽  
Jayarami Reddy B ◽  
Sashidhar C
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Mineral Admixtures ◽  
Test Results ◽  
Concrete Technology ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Strength Concrete

In present era, high-strength concrete is progressively utilized in modern concrete technology and particularly in the construction of elevated structures. This examination has been directed to explore the properties of high-strength concrete that was delivered by using stone powder (SP) as an option of extent on sand after being processed. The aim of the research is to study the effect of replacement of sand with stone powder and substitution of cement with mineral admixtures (GGBS & Zeolite) on the mechanical properties of high strength concrete. The test results showed clear improvement in compression and split tensile nature of concrete by using stone powder and mineral admixtures together in concrete. The increment in the magnitude of compressive strength and split tensile strength are comparable with conventional concrete.

Sign in / Sign up

Export Citation Format

Share Document