scholarly journals Testing And Determining The Temperature Characteristics Of Heat Pipes (HP)

2020 ◽  
Vol 02 (11) ◽  
pp. 151-166
Author(s):  
A.A. Kholikov ◽  
◽  
F.S. Quldosheva ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Pipes ◽  
Working Fluid ◽  
Medium Temperature ◽  
Test Setup ◽  
Temperature Characteristics ◽  
Fluid Body ◽  
Efficient Heat Transfer ◽  
Vegetables And Fruits

The article describes the tests and determination of the temperature characteristics of highly efficient heat transfer units (heat pipes (HP)), which can be used in heat and mass transfer devices, for example, in the process of drying vegetables and fruits. To test and determine the temperature characteristics of HP, a test setup for medium-temperature HP was created and a number of tests were carried out to determine how the dependence of the temperature change of the condenser and the HP evaporator at various angles of inclination, the working fluid, body material, HP wick material was selected, the influence of the number of mesh wick and influence of pressure. All characteristics are presented in graphs and tables.

scholarly journals The effect of operating parameters on the heat transfer in the heat pipe

2021 ◽  
Vol 2119 (1) ◽  
pp. 012088
Author(s):  
A. A. Litvintceva ◽  
N. I. Volkov ◽  
N. I. Vorogushina ◽  
V. A. Moskovskikh ◽  
V. V. Cheverda
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Pipes ◽  
Working Fluid ◽  
Operating Parameters ◽  
Temperature Stabilization ◽  
Ir Camera ◽  
Fluid Properties

Abstract Heat pipes are a good solution for temperature stabilization, for example, of microelectronics, because these kinds of systems are without any moving parts. Experimental research of the effect of operating parameters on the heat transfer in a cylindrical heat pipe has been conducted. The effect of the working fluid properties and the porous layer thickness on the heat flux and temperature difference in the heat pipe has been investigated. The temperature field of the heat pipe has been investigated using the IR-camera and K-type thermocouples. The data obtained by IR-camera and K-type thermocouples have been compared. It is demonstrated the power transferred from the evaporator to the condenser is a linear function of the temperature difference between them.

scholarly journals An investigation on effect of EDL on heat transfer of micro heat pipe with square and triangular cross section

2020 ◽  
Vol 21 (3) ◽  
pp. 309
Author(s):  
Maryam Fallah Abbasi ◽  
Hossein Shokouhmand ◽  
Morteza Khayat
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Double Layer ◽  
Electric Double Layer ◽  
Heat Pipes ◽  
The Body ◽  
Working Fluid ◽  
Two Phase ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Electronic industries have always been trying to improve the efficiency of electronic devices with small dimensions through thermal management of this equipment, thus increasing the use of small thermal sinks. In this study micro heat pipes with triangular and square cross sections have been manufactured and tested. One of the main objectives is to obtain an understanding of micro heat pipes and their role in energy transmission with electrical double layer (EDL). Micro heat pipes are highly efficient heat transfer devices, which use the continuous evaporation/condensation of a suitable working fluid for two-phase heat transport in a closed system. Since the latent heat of vaporization is very large, heat pipes transport heat at small temperature difference, with high rates. Because of variety of advantage features these devices have found a number of applications both in space and terrestrial technologies. The theory of operation micro heat pipes with EDL is described and the micro heat pipe has been studied. The temperature distribution have achieved through five thermocouples installed on the body. Water and different solution mixture of water and ethanol have used to investigate effect of the electric double layer heat transfer. It was noticed that the electric double layer of ionized fluid has caused reduction of heat transfer.

Effects of Surface Coating of Nanoparticles on Thermal Performance of Open Loop Pulsating Heat Pipes

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Ali Adibnia ◽  
Hossein Afshin ◽  
Mohammad Hassan Saidi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Surface Coating ◽  
Heat Pipes ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Performance Of Heat Transfer

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated. Experimental results show that ferrofluid has better heat transport capability relative to SC ferrofluid. Furthermore, application of magnetic field improves the heat transfer performance of OLPHPs charged with both ferrofluids.

Heat Transfer Enhancement of Horizontal Oscillating Heat Pipes With Micro-/Nanostructured Surface

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Tingting Hao ◽  
Huiwen Yu ◽  
Xuehu Ma ◽  
Zhong Lan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Capillary Flow ◽  
Pure Water ◽  
Heat Pipes ◽  
Contact Angles ◽  
Horizontal Direction ◽  
Working Fluid ◽  
Transfer Performance ◽  
Nanostructured Surface

Abstract For oscillating heat pipes (OHPs) with low turn number (<9) positioned in the horizontal direction, the working fluid could not easily flow back to the evaporator due to the absence of gravity. Based on this, copper OHP with superhydrophilic micro-/nanostructured surface was investigated to enhance the heat transfer performance by introducing additional capillary force. OHPs with six turns were fabricated with bare copper and micro-/nanostructured inner surfaces for comparison. Pure water was used as the working fluid. Contact angles of water on the copper and superhydrophilic surfaces were 36.7 and 0 deg, respectively. The filling ratios of water were 50%, 65%, and 80%, respectively. Thermal resistance and liquid slug oscillations of OHPs were investigated at the heat input ranging from 100 to 380 W. Experimental results showed that OHPs with the superhydrophilic micro-/nanostructured surface showed an enhanced heat transfer performance due to the micro-/nanostructure-induced capillary flow in the horizontal direction. The optimum filling ratio was 65% in this work. The superhydrophilic micro-/nanostructured surface could significantly facilitate the backflow of the working fluid to the evaporator section and accelerate oscillating motions of liquid slugs. With the increasing of 0–70% in slug oscillating amplitude and 0–100% in slug oscillating velocity, micro-/nanostructured OHPs improved the heat transfer performance by up to 10% compared with the copper OHPs due to the wicking effect.

Oscillating Heat Pipes for Waste Heat Recovery in HVAC Systems

2015 ◽  
Author(s):  
Govinda Mahajan ◽  
Heejin Cho ◽  
Scott M. Thompson ◽  
Harrison Rupp ◽  
Kevin Muse
Keyword(s):  
Heat Transfer ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Heat Pipes ◽  
Hvac Systems ◽  
Operating Conditions ◽  
Working Fluid ◽  
Low Grade ◽  
Potential Cost

Oscillating heat pipes (OHPs) were experimentally assessed as a passive-type heat transfer device for air-to-air heat exchange in a typical Heating Ventilation & Air conditioning system (HVAC) with adjacent air streams at different temperatures. The objective is to utilize, otherwise wasted thermal energy to pre-heat or pre-cool air in order to reduce the payload on HVAC systems, thus reducing energy consumption. OHPs can achieve effective thermal conductivities on-the-order of 10,000 W/m-K via no internal wicking structure and hence can perform aforementioned heat transfer task while providing an aerodynamic form factor. A unique working fluid with limited research inside OHPs, but with properties desirable for low grade heat fluxes, i.e. n-pentane with 70 % fill ratio, was chosen as the working fluid to achieve maximum heat transfer. Aerodynamic performance, in terms of pressure drop, was evaluated and juxtaposed with heat transfer gain/loss. The OHP thermal performance and total heat transfer for hot-environment HVAC operation was benchmarked with an empty/evacuated OHP with same overall dimensions. Results indicate that the current, atypically-long OHP is fully-capable of operating in the air-to-air convection mode for waste heat recovery for typical HVAC operating conditions. Since the OHP is passive, cost effective, and relatively aerodynamic (no fins were used), the potential cost savings for its integration into HVAC systems can be significant.

Steady State Parametric Modeling of Non-Conventional Loop Heat Pipes

2013 ◽  
Author(s):  
Karthik S. Remella ◽  
Frank M. Gerner ◽  
Ahmed Shuja
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Steady State ◽  
Transfer Coefficient ◽  
Thermal Energy ◽  
Heat Pipes ◽  
Parametric Model ◽  
Parametric Modeling ◽  
Working Fluid ◽  
Loop Heat Pipes

Loop Heat Pipes (LHPs) are used in many thermal management applications, especially for micro-electronics cooling, because of their ability to passively transport thermal energy from a source to a sink. This paper describes the development of a parametric model for a non-conventional LHP operating in steady state, employed to cool Light Emitting Diodes (LEDs). This device is comprised of a flat evaporator, and a finned circular loop wherein condensation and sub-cooling of the working fluid takes place. Unlike a conventional LHP, this device has no compensation chamber. In the mesh screen of the evaporator, the vapor flow entrains liquid and hence the quality of the two-phase mixture leaving the evaporator (xevap) is less than unity (unlike in a conventional LHP where saturated vapor leaves the evaporator). Since this lower quality (approximately 0.2) results in a smaller ratio of latent energy to sensible energy being removed by the condenser and sub-cooler respectively; the ratio of the length of the sub-cooler to condenser length is significantly larger. This results in more stable and controlled operation of the device. Mathematical models of the evaporator, the condenser and the sub-cooler sections are developed, and two closure conditions are employed in this model. For consistency and accuracy, some parameters in the model, such as the natural convection heat transfer coefficient (h o) and a few thermal resistances in the evaporator, are estimated empirically from test data on the device. The empirically obtained value of the heat transfer coefficient is in very good agreement with correlations from the literature. The parametric model accurately predicts the LED board temperature and other temperatures for a specific amount of thermal energy dissipated by the LEDs.

Circulation Effectiveness of Working Fluid in Inclined Micro Heat Pipes

2015 ◽  
Vol 789-790 ◽  
pp. 422-425
Author(s):  
Fun Liang Chang ◽  
Yew Mun Hung
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Pipes ◽  
Operating Conditions ◽  
Circulation Rate ◽  
Working Fluid ◽  
High Heat Flux ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Micro heat pipe is a two-phase heat transfer device offering effective high heat-flux removal in electronics cooling. Essentially, micro heat pipe relies on the phase change processes, namely evaporation and condensation, and the circulation of working fluid to function as heat transfer equipment. The vast applications of micro heat pipe in portable appliances necessitate its functionality under different orientations with respect to gravity. Therefore, its thermal performance is strongly related to its orientation. By incorporating solid wall conduction, together with the continuity, momentum, and energy equations of the working fluid, a mathematical model is developed to investigate the heat and fluid flow characteristics of inclined micro heat pipes. We investigate both the favorable and adverse effects of gravity on the circulation rate which is intimately related to the thermal performance of micro heat pipes. The effects of gravity, through the angle of inclination, on the circulation strength and heat transport capacity are analysed. This study serves as a useful analytical tool in the micro heat pipe design and performance analysis, associated with different inclinations and operating conditions.

scholarly journals Estimation of Cement Thermal Properties through the Three-Phase Model with Application to Geothermal Wells

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2839 ◽  
Author(s):  
Adonis Ichim ◽  
Catalin Teodoriu ◽  
Gioia Falcone
Keyword(s):  
Heat Transfer ◽  
Thermal Properties ◽  
Working Fluid ◽  
Geothermal Systems ◽  
Well Performance ◽  
Three Phase ◽  
Geothermal Wells ◽  
Ancient Times ◽  
Efficient Heat Transfer ◽  
Selection Of

Geothermal energy has been used by mankind since ancient times. Given the limited geographical distribution of the most favorable resources, exploration efforts have more recently focused on unconventional geothermal systems targeting greater depths to reach sufficient temperatures. In these systems, geothermal well performance relies on efficient heat transfer between the working fluid, which is pumped from surface, and the underground rock. Most of the wells designed for such environments require that the casing strings used throughout the well construction process be cemented in place. The overall heat transfer around the wellbore may be optimized through accurate selection of cement recipes. This paper presents the application of a three-phase analytical model to estimate the cement thermal properties. The results show that cement recipes can be designed to enhance or minimize heat transfer around wellbore, extending the application of geothermal exploitation.

Use of an Inorganic Aqueous Solution to Prevent Non-Condensable Gas Formation in Aluminum Heat Pipes

2013 ◽  
Author(s):  
Michael Stubblebine ◽  
Sean Reilly ◽  
Qi Yao ◽  
Ivan Catton
Keyword(s):  
Heat Transfer ◽  
Aqueous Solution ◽  
Heat Pipe ◽  
Heat Pipes ◽  
Solid Metal ◽  
Aluminum Surface ◽  
Working Fluid ◽  
Water Based ◽  
Inorganic Aqueous Solution ◽  
Over Time

Heat pipes are used in many applications as an effective means for transferring heat from a source to a sink. The basic heat pipe typically consists of a solid metal casing within which a working fluid is sealed inside at a given pressure. The latent heat transfer via the heat pipe’s working fluid allows it to carry a larger amount of heat energy than would normally be possible with an identically dimensioned solid metal rod. Water is often used as a working fluid due to its high heat of vaporization and suitable operating range for electronics cooling. For many applications, especially space, aluminum is desired as a casing material for its high thermal conductivity, low weight, and low cost. However, water is incompatible for use with aluminum heat pipes because it forms a non-condensable gas (NCG), hydrogen, when they contact. In this work, an inorganic aqueous solution (IAS), which has thermophysical properties similar to water, has been used as the working fluid with an aluminum alloy 5052-H2 casing. The prepared thermosiphon underwent long-term lifetime testing and the results indicate no tube failure or significant NCG formation for the duration of the 9 week study. Furthermore, the data indicate that the IAS fluid not only inhibited NCG production but also led to a reduction in heat pipe thermal resistance over time. It is believed that the chemicals in IAS react with the aluminum surface to create a compact oxide layer and electrochemical reaction which prevents hydrogen generation. A secondary, hydrophilic surface coating is also generated by the fluid on top of the first oxide (passivation) layer. This hydrophilic layer is believed to be responsible for the heat transfer enhancement which was observed during testing and the reduction in ΔT (defined as Tevap−Tcond) over time. Aluminum heat pipes used currently in practice utilize ammonia, or other non-water based working fluids, which have inferior latent heats of vaporization compared to water or an aqueous-based fluid such as IAS. The use of aluminum heat pipe casings in combination with a water-based fluid such as IAS has the potential to provide a significant increase in heat transport capability per device unit mass over traditional ammonia charged aluminum heat pipes.

Sign in / Sign up

Export Citation Format

Share Document