scholarly journals Optimization of machining parameters in drilling hybrid sisal-cotton fiber reinforced polyester composites

2022 ◽  
Vol 9 (1) ◽  
pp. 119-134
Author(s):  
Nurhusien Hassen Mohammed ◽  
◽  
Desalegn Wogaso Wolla
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Feed Rate ◽  
Hybrid Composite ◽  
Spindle Speed ◽  
Machining Parameters ◽  
Fiber Reinforced ◽  
Roundness Error ◽  
Pull Out ◽  
Drill Diameter

<abstract> <p>Machining natural fiber reinforced polymer composite materials is one of most challenging tasks due to the material's anisotropic property, non-homogeneous structure and abrasive nature of fibers. Commonly, conventional machining of composites leads to delamination, inter-laminar cracks, fiber pull out, poor surface finish and wear of cutting tool. However, these challenges can be significantly reduced by using proper machining conditions. Thus, this research aims at optimizing machining parameters in drilling hybrid sisal-cotton fibers reinforced polyester composite for better machining performance characteristics namely better hole roundness accuracy and surface finish using Taguchi method. The effect of machining parameters including spindle speed, feed rate and drill diameter on drill hole accuracy (roundness error) and surface-roughness of the hybrid composite are evaluated. Series of experiments based on Taguchi's L<sub>16</sub> orthogonal array were performed using different ranges of machining parameters namely spindle speed (600,900, 1200, 1600 rpm), feed rate (10, 15, 20, 25 mm/min) and drill diameter (6, 7, 8, 10 mm). Hole roundness error and surface-roughness are determined using ABC digital caliper and Zeta 20 profilometer, respectively. Optimum machining condition for drilling hybrid composite material (speed: 1600 rpm, feed rate: 25 mm/min and drill diameter: 6 mm) is determined, and the results are verified by conducting confirmation test which proves that the results are reliable.</p> </abstract>

Study on carbon epoxy composite surfaces machined by abrasive water jet machining

2018 ◽  
Vol 53 (20) ◽  
pp. 2909-2924 ◽  
Author(s):  
Ajit Dhanawade ◽  
Shailendra Kumar
Keyword(s):  
Surface Roughness ◽  
Composite Material ◽  
Process Parameters ◽  
Surface Finish ◽  
Epoxy Composite ◽  
Water Jet ◽  
Machining Parameters ◽  
Abrasive Water Jet ◽  
Abrasive Water Jet Machining ◽  
Pull Out

Traditional machining of carbon epoxy composite material is difficult due to excessive tool wear, excessive stresses and heat generation, delamination, high surface waviness, etc. In the present paper, research work involved in the experimental study of abrasive water jet machining of carbon epoxy composite material is described. The aim of present work is to improve surface finish and studying defects in machined samples. Taguchi's orthogonal array approach is used to design experiments. Process parameters namely hydraulic pressure, traverse rate, stand-off distance and abrasive mass flow rate are considered for this study. Analysis of machined surfaces and kerf quality is carried out using scanning electron microscope to evaluate microscopic features. Further, the effect of machining parameters on surface roughness is investigated using analysis of variance approach. It is found that traverse rate and pressure are most significant parameters to control surface roughness. Optimization of process parameters is performed using grey relational analysis. Thereafter, confirmation tests are carried out to verify the improvement in the surface quality with optimum set of process parameters. It is found that surface finish of machined samples is improved by 10.75% with optimum levels of process parameters. Defects like delamination, fiber pull-out and abrasive embedment are also studied using SEM. It is observed that delamination and fiber pull-out are prominent in samples machined at low pressure and high traverse rate.

scholarly journals Optimization of Surface Roughness in Deep Hole Drilling using Moth-Flame Optimization

2019 ◽  
Vol 18 (3-2) ◽  
pp. 62-68
Author(s):  
Anis Farhan Kamaruzaman ◽  
Azlan Mohd Zain ◽  
Razana Alwee ◽  
Noordin Md Yusof ◽  
Farhad Najarian
Keyword(s):  
Surface Roughness ◽  
Optimization Algorithm ◽  
Feed Rate ◽  
Spindle Speed ◽  
Hole Drilling ◽  
P Value ◽  
Machining Parameters ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Moth Flame Optimization Algorithm

This study emphasizes on optimizing the value of machining parameters that will affect the value of surface roughness for the deep hole drilling process using moth-flame optimization algorithm. All experiments run on the basis of the design of experiment (DoE) which is two level factorial with four center point. Machining parameters involved are spindle speed, feed rate, depth of hole and minimum quantity lubricants (MQL) to obtain the minimum value for surface roughness. Results experiments are needed to go through the next process which is modeling to get objective function which will be inserted into the moth-flame optimization algorithm. The optimization results show that the moth-flame algorithm produced a minimum surface roughness value of 2.41µ compared to the experimental data. The value of machining parameters that lead to minimum value of surface roughness are 900 rpm of spindle speed, 50 mm/min of feed rate, 65 mm of depth of hole and 40 l/hr of MQL. The ANOVA has analysed that spindle speed, feed rate and MQL are significant parameters for surface roughness value with P-value <0.0001, 0.0219 and 0.0008 while depth of hole has P-value of 0.3522 which indicates that the parameter is not significant for surface roughness value. The analysis also shown that the machining parameter that has largest contribution to the surface roughness value is spindle speed with 65.54% while the smallest contribution is from depth of hole with 0.8%. As the conclusion, the application of artificial intelligence is very helpful in the industry for gaining good quality of products.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

Surface Roughness Analysis of Carbon/Glass Hybrid Polymer Composites in Drilling Process Based on Taguchi and Response Surface Methodology

2015 ◽  
Vol 1119 ◽  
pp. 622-627 ◽  
Author(s):  
Chye Lih Tan ◽  
Azwan Iskandar Azmi ◽  
Noorhafiza Muhammad
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Regression Model ◽  
Response Surface ◽  
Feed Rate ◽  
Hybrid Composite ◽  
Spindle Speed ◽  
Tool Geometry ◽  
Secondary Process ◽  
Drilling Process

Drilling is an essential secondary process for near net-shape of hybrid composite as to achieve the required dimensional tolerances prior to final application. Dimensional tolerance is often influenced by the surface integrity or surface roughness of the workpart. Thus, this paper aims to employ the Taguchi and response surface methodologies in minimizing the surface roughness of drilled carbon-glass hybrid fibre reinforced polymer (CGCG) using tungsten carbide, K20 drill bits. The effects of spindle speed, feed rate and tool geometry on surface roughness were evaluated and optimum cutting conditions for minimizing the aforementioned response was determined. Subsequently, response surface methodology (RSM) was utilised in finding the empirical relationships between experimental parameters and surface roughness based on the Taguchi results. The experimental analyses reveal that surface roughness is greatly influenced by feed rate and tool geometry rather than the spindle speed. This is due to the increment of feed that attributed to the increased strain rate and hence, deteriorated the surface roughness of the hybrid composite. The predicted results (via regression model) and theoretical results (via additivity law) were in good agreement with experiment results. This indicates that the regression model from response surface methodology (RSM) can be used to predict the surface roughness in machining of CGCG hybrid composite.

scholarly journals EFFECT OF MINIMUM QUANTITY LUBRICATION ON SURFACE ROUGHNESS IN TOOL-BASED MICROMILLING

2017 ◽  
Vol 18 (1) ◽  
pp. 147-154
Author(s):  
Mohammad Yeakub Ali ◽  
Wan Norsyazila Jailani ◽  
Mohamed Rahman ◽  
Muhammad Hasibul Hasan ◽  
Asfana Banu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Spindle Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Microfluidic Channels ◽  
Machining Parameters ◽  
Machining Processes ◽  
Dry Cutting ◽  
Minimum Quantity

Cutting fluid plays an important role in machining processes to achieve dimensional accuracy in reducing tool wear and improving the tool life. Conventional flood cooling method in machining processes is not cost effective and consumption of huge amount of cutting fluids is not healthy and environmental friendly. In micromachining, flood cooling is not recommended to avoid possible damage of the microstructures. Therefore, one of the alternatives to overcome the environmental issues to use minimum quantity of lubrication (MQL) in machining process. MQL is eco-friendly and has economical advantage on manufacturing cost. However, there observed lack of study on MQL in improving machined surface roughness in micromilling. Study of the effects of MQL on surface roughness should be carried out because surface roughness is one of the important issues in micromachined parts such as microfluidic channels. This paper investigates and compares surface roughness with the presence of MQL and dry cutting in micromilling of aluminium alloy 1100 using DT-110 milling machine. The relationship among depth of cut, feed rate, and spindle speed on surface roughness is also analyzed. All three machining parameters identified as significant for surface roughness with dry cutting which are depth of cut, feed rate, and spindle speed. For surface roughness with MQL, it is found that spindle speed did not give much influence on surface roughness. The presence of MQL provides a better surface roughness by decreasing the friction between tool and workpiece.

scholarly journals Surface roughness of thermally treated wood cut with different parameters in CNC router machine

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5133-5147
Author(s):  
Hüseyin Pelit ◽  
Mustafa Korkmaz ◽  
Mehmet Budakçı
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Treatment Temperature ◽  
Spindle Speed ◽  
Numerical Control ◽  
Machining Parameters ◽  
End Mill ◽  
Cnc Machine ◽  
Cnc Router ◽  
Thermally Treated

The effects of different machining parameters on surface roughness values of thermally treated pine, beech, and linden woods cut in a computer numerical control (CNC) router machine were examined. Wood specimens were thermally treated at 170, 190, and 210 °C for 2 h. Then, specimens were cut in the radial and tangential directions with three different spindle speeds (12000, 15000, and 18000 rpm) and three different feed rates (3000, 4000, and 6000 mm/min) using two different end mill tools (spiral and straight) on the CNC machine. The end mill type significantly affected the roughness values of the untreated and thermally treated specimens in both directions. Lower roughness values were found in the specimens (especially pine) machined with the straight end mill compared to those machined with the spiral end mill. Roughness generally decreased in the thermally treated specimens. However, thermal treatment temperature did not have a notable effect on roughness. As the spindle speed increased, the roughness values of all specimens decreased. In contrast, as the feed rate increased, the roughness values increased. Therefore, the end mill type, feed rate, and spindle speed were the most influential parameters on the roughness.

scholarly journals The influence of machining parameters on surface roughness of MDF in milling operation

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 3266-3277
Author(s):  
Ümmü K. İşleyen ◽  
Mehmet Karamanoğlu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Medium Density Fiberboard ◽  
Spindle Speed ◽  
Numerical Control ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Milling Operation ◽  
Four Levels ◽  
Tool Diameter

This paper examined the effect of machining parameters on surface roughness of medium density fiberboard (MDF) machined using a computer numerical control (CNC) router. The machining parameters such as spindle speed, feed rate, depth of cut, and tool diameter were examined for milling. The experiments were conducted at two levels of spindle speeds, four levels of feed rates, two levels of tool diameters, and two levels of axial depths of cut. The surface roughness values of MDF grooved by CNC were measured with stylus-type equipment. Statistical methods were used to determine the effectiveness of the machining parameters on surface roughness. The influence of each milling parameter affecting surface roughness was analyzed using analysis of variance (ANOVA). The significant machining parameters affecting the surface roughness were the feed rate, spindle speed, and tool diameter (p < 0.05). There was no significant influence of axial depth of cut on the surface roughness. The surface roughness decreased with increasing spindle speed and decreasing feed rate. The value of surface roughness increased with the increase of tool diameter.

Study of Machining Parameter Optimization in Drilling of Magnesium Based Hybrid Composites Reinforced with SiC/CNT

2020 ◽  
Vol 846 ◽  
pp. 42-46 ◽  
Author(s):  
J.S.Suresh Babu ◽  
Min Heo ◽  
Chung Gil Kang
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Hybrid Composites ◽  
Spindle Speed ◽  
Influential Factor ◽  
Burr Formation ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Wide Range ◽  
Machining Parameter

Recently, researchers and engineers have been interested in the development of hybrid metal matrix composites (HMMCs) for the applications of automotive and aerospace industries owing to their superior properties due to the usage a wide range of material combinations in its manufacturing. The present study focuses on the machining of magnesium based hybrid composites reinforced with CNT (1vol.%) and SiC (2vol.%).The influence of machining parameters such as spindle speed, feed rate, drill diameter and point angle on burr formation and surface roughness on drilling the composites were investigated using Taguchi method. The drilling parameters were optimized by using ANOVA experimental design and also find out the percentage of contribution of each factor. Based on the results, the most influential factor for the burr thickness was spindle speed and point angle. While spindle speed and feed rate were the influencing factors for surface roughness. The analysis revealed that burr height, burr thickness, and surface roughness decreases significantly with an increase in spindle speed.

FRACTAL-BASED ANALYSIS OF THE EFFECT OF MACHINING PARAMETERS ON SURFACE FINISH OF WORKPIECE IN TURNING OPERATION

Fractals ◽  
2019 ◽  
Vol 27 (04) ◽  
pp. 1950043 ◽  
Author(s):  
GEEVIN JITHMAL PATHIRANAGAMA ◽  
HAMIDREZA NAMAZI
Keyword(s):  
Surface Quality ◽  
Surface Finish ◽  
Feed Rate ◽  
Fractal Theory ◽  
Complex Structure ◽  
Spindle Speed ◽  
Machining Parameters ◽  
Cutting Depth ◽  
Machined Surface ◽  
Turning Operation

Analysis of workpiece surface quality is one of the major issues in manufacturing engineering. Turning operation is a famous machining operation that is widely used in machining of materials. In this research, we investigate the surface finish of machined workpiece from turning operation. For this purpose, we employ fractal theory to study the complex structure of machined workpiece’s surface in different conditions. The applied parameters include the variations of cutting depth, feed rate and spindle speed in wet and dry machining conditions. Based on the obtained results, we found the correlation between the increment of fractal dimension of machined surface and the increment of cutting depth, feed rate and spindle speed in wet machining condition. The obtained results will be discussed in relation with the complexity of machined surface. The employed method of analysis in this research can be widely applied to the analysis of the effect of different machining parameters and conditions on the surface quality of machined workpiece in case of different machining operations.

Effects of Cutting Parameters on Hole Integrity when Drilling GFRP and HFRP Composites

2013 ◽  
Vol 845 ◽  
pp. 960-965
Author(s):  
Mohd Azuwan Maoinser ◽  
Faiz Ahmad ◽  
Safian Sharif
Keyword(s):  
Composite Materials ◽  
Feed Rate ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Matrix Cracking ◽  
Fiber Reinforced ◽  
Damage Factor ◽  
Electron Microscopic ◽  
Pull Out

The demand for mechanical fastening in composite materials is increasing due to their potential in large assemblies, aerospace and automotive industries. In practice, small components are integrated into large assemblies drilling holes in composite materials. Drilling defect free holes in composite presents many challenges during part assembly and services. This study presents the effects of cutting parameters used for drilling holes in glass fiber reinforced polymeric (GFRP) composites and hybrid fiber reinforced polymeric (HFRP) composites. Both the composites plates of 3 mm thickness were fabricated using a hand lay-up technique for the purpose of evaluating the effects of parameters on the quality of drilled holes. The holes were drilled using a 5 mm solid carbide twist drill at different spindle speed and feed rate. The quality of holes was assessed with respect to damage factor (Fd) and surface roughness (Ra) of the drilled holes. Results showed that the HFRP composite experienced lower damage factor (Fd) as compared to GFRP composite at lower feed rate or spindle speed. Scanning electron microscopic (SEM) examination revealed that the occurrence of delamination, fiber pull-out and matrix cracking was accelerated in the drilled holes at high spindle speed and feed rate.

Sign in / Sign up

Export Citation Format

Share Document