Performance of Mortar Grouts Incorporating Rice Husk Ash and Fly Ash

2019 ◽  
pp. 31-48
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Apparent Volume ◽  
Partial Replacement ◽  
Hardened State ◽  
Strength And Durability ◽  
Penetration Tests

Chapter 3 is based on performance of mortar grouts incorporating rice husk ash (RHA) and fly ash (FA). Detailed experimental work was conducted to investigate the mechanical properties of mortar grout using RHA and FA as partial replacement of cement. This study investigated the compressive strength and durability of mortar grouts in their hardened state. Durability tests such as water absorption, apparent volume of permeable voids, sorptivity, and rapid chloride penetration tests are researched. Detailed results and discussion which focused on mechanical properties as well as durability of hardened state mortar grout are presented. It was confirmed that the inclusion of blended RHA and FA significantly improved the compressive strength of mortar grouts. The durability of mortar grout increased along with a longer curing time. Hence, RHA and FA can partially replace cement in the production of mortar grouts.

Use of Water Glass from Rice Husk and Bagasse Ashes in the Preparation of Fly Ash Based Geopolymer

2019 ◽  
Vol 798 ◽  
pp. 364-369 ◽  
Author(s):  
Khemmakorn Gomonsirisuk ◽  
Parjaree Thavorniti
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Ball Mill ◽  
Water Glass ◽  
Rice Husk Ash ◽  
Raw Materials ◽  
Agricultural Waste ◽  
Preparation Process

The aim of this work is to study the feasibility of preparation of fly ash based geopolymer using sodium water glass from agricultural waste as alternative activators. Rice husk ash and bagasse ash were used as raw materials for producing sodium water glass solution. The sodium water glass were produced by mixing rice husk ash and bagasse ash with NaOH in ball mill and boiling. The prepared sodium water glass were analyzed and used in geopolymer preparation process. The geopolymer paste were prepared by adding the obtained water glass and NaOH with fly ash. After cured at ambient temperature for 7 days, mechanical properties were investigated. Bonding and phases of the geopolymer were also characterized. The geopolymer from rice husk ash presented highest compressive strength about 23 MPa while the greatest for bagasse ash was about 16 MPa.

scholarly journals Study of Fly Ash, Rice Husk Ash and Marble Powder as Partial Replacement to Cement in Concrete

2020 ◽  
Vol 13 (3) ◽  
pp. 315-321
Author(s):  
Dhiraj Ahiwale ◽  
Rushikesh Khartode
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Scale Production ◽  
Environmental Threat ◽  
Marble Powder

Now days, the waste rice husk from rice mill, marble powder from tile industry and fly ash from steam power plant are necessary to utilize as partial replacement of cement for concrete production. Large scale production of cement required consumption of raw materials and energy as well as emissions to air which posse’s environmental threat in various areas of country. Apart from the environmental threat, there still exists the problem of shortage in many areas. Therefore, substitute material for concrete needs to be considered. The paper aims to analyze the compressive strength of concrete cubes and flexural strength of concrete beams made from partially replaced cement, sand, and coarse aggregate. This research study adopted in laboratory on 48 total specimens of grade M25 concrete cubes of size 150x150x150mm and concrte beams of size 100x100x500mm were casted. Out of the 48 concrete specimens cast, 6 each were made out 10%, 20%, and 30 % replacement of fly ash, rice husk ash and marble powder to cement in concrete. It was found that the compressive strength and flexural strength of concrete made from the mixture of 20 % partially replaced cement, sand and coarse aggregate was similar than the concrete made from without replaced cement , sand and coarse aggregate.

scholarly journals Efficiency of rice husk ash and fly ash as reactivity materials in sustainable concrete

2019 ◽  
Vol 29 (1) ◽  
Author(s):  
Mohamed Amin ◽  
Bassam Abdelsalam Abdelsalam
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Rice Husk ◽  
Water Permeability ◽  
Rice Husk Ash ◽  
Experimental Program ◽  
Hardened Concrete ◽  
Concrete Mixtures

AbstractMany environmental problems occur due to rice husk burning and emissions from coal-fired power stations. This paper presents the recycling of rice husk ash (RHA) and fly ash (FA) from power plants as reactivity materials for producing sustainable (green) concrete. This research aims to investigate the efficiency of RHA and FA replacement ratios on fresh and hardened properties of concrete mixtures. The experimental program consisted of 21 concrete mixtures, which were divided into three groups. The cementitious material contents were 350, 450 and 550 kg m−3 for groups one, two and three, respectively. The replacement ratios from the cement content were 10, 20 and 30% respectively, for each recycle material (RHA and FA). The slump and air contents of fresh concrete were measured. The compressive strength, splitting tensile strength, flexural strength, modulus of elasticity and bond strength of hardened concrete as mechanical properties were also analyzed. The compressive strength was monitored at different ages: 3, 7, 28, 60 and 90 d. The water permeability test of hardened concrete as physical properties was conducted. Test results showed that the RHA and FA enhanced the mechanical and physical properties compared with the control mixture. The cementitious content of 450 kg m−3 exhibited better results than other utilized contents. In particular, the replacement ratios of 10 and 30% of RHA presented higher mechanical properties than those of FA for each group. The water permeability decreased as the cementitious content increased due to the decrease in air content for all mixtures. The water permeability loss ratios increased as the cementitious content decreased.

scholarly journals Review on Accelerated Carbonation on the Properties of Concrete

2021 ◽  
Vol 10 (3) ◽  
pp. 63-66
Author(s):  
Rajani V Akki ◽  
K.E. Prakash
Keyword(s):  
Carbon Dioxide ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Daily Routine ◽  
Accelerated Carbonation ◽  
Carbonation Process ◽  
Strength And Durability

Concrete is an essential material in all constructions throughout the world. It has lot of uses in our daily routine life. Every material has to deteriorate and damage due to many factors in the same way the concrete also deteriorates. The carbonation process is identified as a main reason for the corrosion in reinforcement concrete structure. The mechanism of carbonation which includes the entrance of carbon dioxide (CO2) into the solid permeable framework of concrete to shape a situation by decreasing the pH around the fortification and inception of the corrosion procedure. This paper investigates the impact of the carbonation on the characteristics of the concrete like strength in compression, split tensile strength, flexural strength, shear strength and durability. The addition of supplementary cementitious materials like fly ash, GGBFS, rice husk ash, metakaolin is known to enhance the strength and durability of concrete in construction. In this paper an accelerated carbonation test has been done to assess concrete carbonation on specimens made with cement and with the partial replacement of cement by fly ash GGBFS, rice husk ash, metakaolin. An accelerated carbonation chamber has been constructed for creating an environment of carbonation process to occur and also the passage of carbon dioxide gas is kept constant for all the cubes, cylinders and beams. Concrete cubes, cylinders and beams are prepared for M30 grade subjected to different percentages of carbonation.

scholarly journals Compressive Strength of Concrete using Fly Ash and Rice Husk Ash: A Review

2020 ◽  
Vol 6 (7) ◽  
pp. 1400-1410
Author(s):  
Joel Sam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Compressive Strength Of Concrete ◽  
Minor Compounds

Decreasing our over-reliance on cement as an ingredient in the making of concrete due to its contribution to the CO2 emissions has led to numerous researches been conducted to find suitable replacement for cement in concrete mixes.  Materials like fly ash, ground granulated blast furnace slag, silica fume, rice husk ash and metakaolin among others have been identified as materials that can at the very least be used as a replacement for cement in concrete mix. These materials are referred to as supplementary cementitious materials (SCMs). This paper reviewed the work that has been done on the use of fly ash and rice husk ash as partial replacements for concrete, its chemical composition and its effect on the compressive strength of concrete. Charts, tables and figures were employed as tools to study the various chemical compounds of fly ash and rice husk ash. It was seen that depending on how the coal or rice husk was initially processed the percentage of some of the minor compounds like Sodium oxide (Na2O), Titanium oxide (TiO2) and Phosphorus pentoxide (P2O5) were sometimes very low or not recorded as part of the final product.  The data on the compressive strength of concrete after fly ash and rice husk ash had been added in percentage increments of 0%, 10%, 20%, 30%, 40%, 50% and 0%, 5%, 7.5%, 10%, 12.5%, 15% respectively analysed over a minimum period of 7 days and a maximum period of 28 days found out that the optimal percentage partial replacement of fly ash and rice husk ash for a strong compressive concrete strength is 30% of fly ash and 7.5% of rice husk ash.

Physical Properties of Cement Mortar Containing Waste Ash

2015 ◽  
Vol 804 ◽  
pp. 129-132
Author(s):  
Sumrerng Rukzon ◽  
Prinya Chindaprasirt
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Cement Mortar ◽  
Ash Content ◽  
Water Requirement ◽  
Test Results ◽  
Pozzolanic Material ◽  
Materials Used

This research studies the potential for using waste ash from industrial and agricultural by-products as a pozzolanic material. Classified fly ash (FA) and ground rice husk ash (RA) were the materials used. Water requirement, compressive strength and porosity of cement mortar were investigated. Test results indicated that FA and RA (waste ash) have a high potential to be used as a good pozzolanic material. The water requirement of mortar mix decreases with the increases in fly ash content. For ground rice husk ash (RA), the water requirement of mortar mix increases with the increases in rice husk ash content. In addition, the reduction in porosity was associated with the increase in compressive strength.

scholarly journals Strength and Durability Performance of Alkali-Activated Rice Husk Ash Geopolymer Mortar

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Yun Yong Kim ◽  
Byung-Jae Lee ◽  
Velu Saraswathy ◽  
Seung-Jun Kwon
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Polymerization Reaction ◽  
Strength Development ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Mix Proportion ◽  
Strength And Durability ◽  
Alkali Activated

This paper describes the experimental investigation carried out to develop the geopolymer concrete based on alkali-activated rice husk ash (RHA) by sodium hydroxide with sodium silicate. Effect on method of curing and concentration of NaOH on compressive strength as well as the optimum mix proportion of geopolymer mortar was investigated. It is possible to achieve compressive strengths of 31 N/mm2and 45 N/mm2, respectively for the 10 M alkali-activated geopolymer mortar after 7 and 28 days of casting when cured for 24 hours at 60°C. Results indicated that the increase in curing period and concentration of alkali activator increased the compressive strength. Durability studies were carried out in acid and sulfate media such as H2SO4, HCl, Na2SO4, and MgSO4environments and found that geopolymer concrete showed very less weight loss when compared to steam-cured mortar specimens. In addition, fluorescent optical microscopy and X-ray diffraction (XRD) studies have shown the formation of new peaks and enhanced the polymerization reaction which is responsible for strength development and hence RHA has great potential as a substitute for ordinary Portland cement concrete.

scholarly journals Mix Design of Grade M35 by Replacement of Cement with Rice Husk Ash in Concrete

2018 ◽  
Vol 8 (03) ◽  
Author(s):  
Savita Chaudhary ◽  
Aditya Pratap Singh
Keyword(s):  
Rice Husk ◽  
Carbon Dioxide Emissions ◽  
Rice Husk Ash ◽  
Strength Properties ◽  
Environmental Benefits ◽  
Partial Replacement ◽  
Pozzolanic Material ◽  
Concrete Production ◽  
Cement And Concrete ◽  
Strength And Durability

The optimized RHA, by controlled burn or grinding, has been used as a pozzolanic material in cement and concrete. Using it provides several advantages, such as improved strength and durability properties, and environmental benefits related to the disposal of waste materials and to reduced carbon dioxide emissions. Up to now, little research has been done to investigate the use of RHA as supplementary material in cement and concrete production .The main objective of this work is to study the suitability of the rice husk ash as a pozzolanic material for cement replacement in concrete. However it is expected that the use of rice husk ash in concrete improve the strength properties of concrete. Also it is an attempt made to develop the concrete using rice husk ash as a source material for partial replacement of cement, which satisfies the

scholarly journals Effect of Incorporation of Rice Husk Ash Instead of Cement on the Performance of Steel Fibers Reinforced Concrete

2021 ◽  
Vol 8 ◽  
Author(s):  
Osama Zaid ◽  
Jawad Ahmad ◽  
Muhammad Shahid Siddique ◽  
Fahid Aslam
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Steel Fibers ◽  
Concrete Compressive Strength ◽  
Brittle Behavior ◽  
Direct Combustion ◽  
Low Performance ◽  
Strength And Durability ◽  
Reference Samples

The production of rice is significant worldwide; the husk produced is generally used as a combustible material for the preparation of paddies, delivering energy through direct combustion as well as by gasifying. Annually, 7.4 million tons of Rice Husk Ash (RHA) is produced and poses an incredible danger to the environment, harming the land and the encompassing zone where it is unloaded. In the transformation of rice husk to ash, the ignition cycle eliminates the natural products, leaving silica-rich remains. These silica-rich remains have proven to have potential to be utilized in concrete as a limited substitution of cement to enhance the concrete compressive strength. Steel fibers’ incorporation increases the concrete tensile strength, balances out concrete samples, and changes their brittle behavior to a more ductile response. In the current study, the influence of various doses of Rice Husk Ash (RHA) used in concrete in the presence and absence of steel fibers and concrete performance has been examined. A total of nine mixes have been designed: one was a control, four were without steel fibers containing only RHA, and the last four mixed RHA with steel fibers from 0.5 to 2%. Tests with 5, 10, 15, and 20% percentages of RHA replacing the concrete have been targeted. Results have been compared with the reference samples and the reasonability of adding Rice Husk Ash to concrete has been studied. From the results, it was noted that about 10% of cement might be replaced with Rice Husk Ash mixed in with steel fibers with almost equal compressive strength. Replacing more than 15% of cement with RHA will produce concrete with a low performance in terms of strength and durability.

scholarly journals Development of a Zero-Cement Binder Using Slag, Fly Ash, and Rice Husk Ash with Chemical Activator

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
M. R. Karim ◽  
M. F. M. Zain ◽  
M. Jamil ◽  
F. C. Lai
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Setting Time ◽  
Time Flow ◽  
Alumina Gel ◽  
Cement Binder ◽  
Increasing Demand ◽  
Chemical Activator

The increasing demand and consumption of cement have necessitated the use of slag, fly ash, rice husk ash (RHA), and so forth as a supplement of cement in concrete construction. The aim of the study is to develop a zero-cement binder (Z-Cem) using slag, fly ash, and RHA combined with chemical activator. NaOH, Ca(OH)2, and KOH were used in varying weights and molar concentrations. Z-Cem was tested for its consistency, setting time, flow, compressive strength, XRD, SEM, and FTIR. The consistency and setting time of the Z-Cem paste increase with increasing RHA content. The Z-Cem mortar requires more superplasticizer to maintain a constant flow of110±5% compared with OPC. The compressive strength of the Z-Cem mortar is significantly influenced by the amounts, types, and molar concentration of the activators. The Z-Cem mortar achieves a compressive strength of 42–44 MPa at 28 days with 5% NaOH or at 2.5 molar concentrations. The FTIR results reveal that molecules in the Z-Cem mortar have a silica-hydrate (Si-H) bond with sodium or other inorganic metals (i.e., sodium/calcium-silica-hydrate-alumina gel). Therefore, Z-Cem could be developed using the aforementioned materials with the chemical activator.

Sign in / Sign up

Export Citation Format

Share Document