Multivariate Optimization of the Cutting Parameters when Turning Slender Components

2012 ◽  
Vol 2 (4) ◽  
pp. 12-31 ◽  
Author(s):  
A.R. Silva Filho ◽  
A.M. Abrão ◽  
A.P. Paiva ◽  
J.R. Ferreira
Keyword(s):  
Surface Roughness ◽  
Slenderness Ratio ◽  
Cutting Speed ◽  
Principal Component ◽  
Cutting Parameters ◽  
Medium Carbon Steel ◽  
Depth Of Cut ◽  
Work Piece ◽  
Multivariate Optimization

The geometric features of the work piece and the cutting parameters considerably affect the quality of a finished part subjected to any machining operation owing to the imposed elastic and plastic deformations, especially when slender components are produced. This work is focused on the influence of the work piece slenderness ratio and cutting parameters on the quality of the machined part, assessed in terms of surface roughness and both geometric (run-out) and dimensional (diameter) deviations. Turning tests with coated tungsten carbide tools were performed using AISI 1045 medium carbon steel as work material. Differently from the published literature, a statistical analysis based on the multivariate one-way analysis of variance (MANOVA) was applied to the data obtained using a Box-Behnken experimental design. In order to identify the combination of parameters (slenderness ratio, cutting speed, feed rate and depth of cut) levels which simultaneously optimize the responses of interest (surface roughness, run-out and diameter deviation), a multivariate optimization method based on principal component analysis (PCA) and generalized reduced gradient (GRG) was employed.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

scholarly journals Effects of Cutting Parameters on Quality of Surface Produced by Machining of Titanium Alloy and Their Optimization

2016 ◽  
Vol 63 (4) ◽  
pp. 531-548 ◽  
Author(s):  
◽  
B.P. Agrawal ◽  
Iqbal A. Khan ◽  
Zahid A. Khan
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
High Performance ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Poor Quality ◽  
Depth Of Cut ◽  
Turbine Engine ◽  
Marine Applications

Abstract Titanium alloy (Ti-6Al-4V) has been extensively used in aircraft turbine-engine components, aircraft structural components, aerospace fasteners, high performance automotive parts, marine applications, medical devices and sports equipment. However, wide-spread use of this alloy has limits because of difficulty to machine it. One of the major difficulties found during machining is development of poor quality of surface in the form of higher surface roughness. The present investigation has been concentrated on studying the effects of cutting parameters of cutting speed, feed rate and depth of cut on surface roughness of the product during turning of titanium alloy. Box-Behnken experimental design was used to collect data for surface roughness. ANOVA was used to determine the significance of the cutting parameters. The model equation is also formulated to predict surface roughness. Optimal values of cutting parameters were determined through response surface methodology. A 100% desirability level in the turning process for economy was indicated by the optimized model. Also, the predicted values that were obtained through regression equation were found to be in close agreement to the experimental values.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Experimental Determination of Optimal Speeds for Alloy Steels in Plane Turning

2008 ◽  
Author(s):  
T. Srikanth ◽  
V. Kamala
Keyword(s):  
Surface Roughness ◽  
Force Measurement ◽  
Cutting Speed ◽  
Vital Role ◽  
The Other ◽  
Depth Of Cut ◽  
Work Piece ◽  
Material Interface ◽  
Alloy Steels

In machining, speeds play vital role. The operator should know exactly the speed at which machining should be performed to get the required surface finish. In this paper, an attempt is made to determine the optimal cutting speed for machining of alloy steels. Three work piece materials having different hardness are taken and machined using a round nose tool with a coated tip. The tool dynamometer is attached to the tool post for force measurement. Turning operation on the work piece is performed on lathe at four different speeds, keeping the feed and depth of cut constant. Cutting forces acting on the tool, temperature at the tool and material interface are recorded. Power consumed being determined by a wattmeter and surface roughness values are measured. The same procedure is repeated for the other two work-pieces materials and optimal speeds for machining are determined for the three specimens. The results obtained are compared with the theoretical values and found to be very close.

Evaluation of Process Parameters in Machining of AA6063 Alloy

2018 ◽  
Vol 1148 ◽  
pp. 109-114
Author(s):  
M. Balaji ◽  
C.H. Nagaraju ◽  
V.U.S. Vara Prasad ◽  
R. Kalyani ◽  
B. Avinash
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Process Parameters ◽  
Single Channel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Aa6063 Alloy

The main aim of this work is to analyse the significance of cutting parameters on surface roughness and spindle vibrations while machining the AA6063 alloy. The turning experiments were carried out on a CNC lathe with a constant spindle speed of 1000rpm using carbide tool inserts coated with Tic. The cutting speed, feed rate and depth of cut are chosen as process parameters whose values are varied in between 73.51m/min to 94.24m/min, 0.02 to 0.04 mm/rev and 0.25 to 0.45 mm respectively. For each experiment, the surface roughness parameters and the amplitude plots have been noted for analysis. The output data include surface roughness parameters (Ra,Rq,Rz) measured using Talysurf and vibration parameter as vibration amplitude (mm/sec) at the front end of the spindle in transverse direction using single channel spectrum analyzer (FFT).With the collected data Regression analysis is also performed for finding the optimum parameters. The results show that significant variation of surface irregularities and vibration amplitudes were observed with cutting speed and feed. The optimum cutting speed and feed from the regression analysis were 77.0697m/min and 0.0253mm/rev. for the minimum output parameters. No significant effect of depth of cut on output parameters is identified.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Improvement of Surface Roughness in End Milling of Ti6Al4V by Coupling RSM with Genetic Algorithm

2011 ◽  
Vol 264-265 ◽  
pp. 1154-1159
Author(s):  
Anayet Ullah Patwari ◽  
A.K.M. Nurul Amin ◽  
S. Alam
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Titanium Alloys ◽  
End Milling ◽  
Fitness Function ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Resistance Surface

Titanium alloys are being widely used in the aerospace, biomedical and automotive industries because of their good strength-to-weight ratio and superior corrosion resistance. Surface roughness is one of the most important requirements in machining of Titanium alloys. This paper describes mathematically the effect of cutting parameters on Surface roughness in end milling of Ti6Al4V. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. The experimental results indicate that the proposed mathematical models suggested could adequately describe the performance indicators within the limits of the factors that are being investigated. The developed RSM is coupled as a fitness function with genetic algorithm to predict the optimum cutting conditions leading to the least surface roughness value. MATLAB 7.0 toolbox for GA is used to develop GA program. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to achieve the minimum surface roughness value.

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

Study on Factors which Make CBN Insert can Turn S45C Steel Have Surface Roughness Less than Ra 0.4

2019 ◽  
Vol 805 ◽  
pp. 3-7
Author(s):  
Manus Sriswat ◽  
Kittipong Kimapong ◽  
Atthakorn Chanchana
Keyword(s):  
Surface Roughness ◽  
Contact Area ◽  
Cubic Boron Nitride ◽  
Cutting Speed ◽  
Medium Carbon Steel ◽  
Depth Of Cut ◽  
Grinding Process ◽  
Standard Type ◽  
Good Surface ◽  
Cylindrical Parts

Grinding process is necessary final process of making cylindrical parts with less than Ra 0.4 surface roughness. Generally we cannot obtain good surface quality without grinding process. As the experience of the authors, using CBN (Cubic Boron Nitride) insert to turning cylindrical parts could be obtained Ra 0.438 surface roughness. The surface roughness result is similar to ground parts. This result becomes the main focus of the study. Authors study to find out factors affecting CBN performance in turning with CBN to obtain less than Ra 0.4 surface roughness. According to the study, it was found that tool contact area allied to surface roughness. The experiment is turning S45C medium carbon steel under the following condition: Cutting speed is 300 m./min, Feed is 0.05 mm./rev and depth of cut is 0.1 mm. Experiment under the same condition in different contact area. Modify contact area of CBN insert to be 5,10,15,20 and 25 mm. and testing in order. CBN insert standard type contact area is 0 mm. Compare test results of modified CBN inserts with standard type result. The results of experiments were as follows: 1) Turning steel with CBN contact area 10 mm. was obtained Ra 0.456 surface roughness, 2) Turning steel with CBN contact area 15 mm. was obtained Ra 0.293 surface roughness, Thus less than Ra 0.4 surface roughness.

Sign in / Sign up

Export Citation Format

Share Document