Experimental Study on Carbonation Resistance of Ready-Mixed Concrete

2012 ◽  
Vol 174-177 ◽  
pp. 152-158 ◽  
Author(s):  
Jing Song Zhu ◽  
Ya Li Sun ◽  
Yue Feng Zhu ◽  
Dan Fei Chen
Keyword(s):  
Fly Ash ◽  
Service Life ◽  
Early Stage ◽  
Ash Content ◽  
Design Criteria ◽  
Carbonation Depth ◽  
Curing Conditions ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Carbonation Resistance

By means of accelerated carbonation tests, the carbonation resistance of concrete in relation to the variation of water-cement ratio, fly ash content and curing conditions is studied in this article. The results show that under the standard curing conditions, with the fly ash content of 20%, in response to different water-cement ratio, the carbonation depth of concrete and the water-cement ratio are presented more or less in a linear relationship. At the water-cement ratio of 0.40, there is hardly any carbonation effect onto the concrete. However, at the ratio of bigger than 0.60, the carbonation depth of concrete increases in a speedy way. Under the standard curing conditions, at the water-cement ratio of 0.55, with the fly ash content of lower than or equal to 30%, the carbonation resistance of concrete is good enough to fulfill the design criteria of 50~100 years for service life of important and general buildings, while the compressive strength declines by less than 10%. But under the condition of 1d curing with retention of moisture followed by curing in the air until 28d, with no fly ash content, the carbonation depth of concrete has reached 35mm, which fails to fulfill the design criteria of 50 years for service life of general buildings. It is therefore concluded that the control of water-cement ratio, the control of fly ash content, and the sufficient curing with retention of moisture in early stage are all the essential factors to ensure the durability against carbonation for the concrete with fly ash content.

Assessment of Hydration Degree of Cement in the Fly Ash-Cement Pastes Based on the Calcium Hydroxide Content

2014 ◽  
Vol 875-877 ◽  
pp. 177-182 ◽  
Author(s):  
Xiang Li ◽  
Hua Quan Yang ◽  
Ming Xia Li
Keyword(s):  
Fly Ash ◽  
Calcium Hydroxide ◽  
Cement Hydration ◽  
Ash Content ◽  
Content Increase ◽  
Hydration Degree ◽  
Equilibrium Calculation ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water Cement Ratio

The hydration degree of fly ash and the calcium hydroxide (CH) content were measured. Combined with the equilibrium calculation of cement hydration, a new method for assessment of the hydration degree of cement in the fly ash-cement (FC) pastes based on the CH content was developed. The results reveal that as the fly ash content increase, the hydration degree of fly ash and the CH content decrease gradually; at the same time, the hydration degree of cement increase. The hydration degree of cement in the FC pastes containing a high content of fly ash (more than 35%) at 360 days is as high as 80%, even some of which hydrates nearly completely. The effect of water-cement ratio to the hydration degree of cement in the FC pastes is far less distinct than that of the content of fly ash.

Variation of Carbonation Coefficient of Pumping Concrete with Moist-Curing Time at early Ages and Fly-Ash Content

2011 ◽  
Vol 287-290 ◽  
pp. 899-905
Author(s):  
Qing Ye ◽  
Zhi Wei Song ◽  
Guo Rong Yu
Keyword(s):  
Fly Ash ◽  
Concrete Cover ◽  
Ash Content ◽  
Curing Time ◽  
Accelerated Carbonation ◽  
Carbonation Depth ◽  
Carbonation Resistance

Based on accelerated carbonation test, the variation of carbonation resistance of pumping concrete (C40 grade) with moist-curing time at early ages and fly-ash content was studied. Results indicate that the carbonation coefficient and the accelerated carbonation depth of the concrete increased obviously with a reduction in the moist-curing time at early ages and with an increase in the fly-ash content. For example, in conditions of curing schedules with 28, 7, 3, 2 and 1 d moist-curing at 20 0C with above 95% RH at early ages and then 0, 21, 25, 26 and 27 d air curing at 20 0C with 60% RH, respectively, carbonation coefficients of the concrete incorporated with 30% fly-ash were 2.04, 2.49, 3.16, 3.86 and 5.42 mm/a0.5 respectively, and thus it can be seen that the calculated times when concrete cover (25 mm) was completely carbonated naturally in now atmosphere (0.04% CO2) were 164, 104, 66, 44 and 21 years respectively. The results suggest that for the carbonation resistance of the C40 concrete incorporated with up to 30% fly-ash, the moist-curing time of 7 days at early ages should be necessary.

Research on the Variation of pH Value of the Ordinary Concrete and Fly Ash Concrete in the Carbonation Process

2011 ◽  
Vol 374-377 ◽  
pp. 1934-1937 ◽  
Author(s):  
Guang Zheng Qi ◽  
Di Tao Niu ◽  
Cheng Fang Yuan ◽  
Fu Zhen Duan
Keyword(s):  
Fly Ash ◽  
High Performance ◽  
Ph Value ◽  
Economic Benefits ◽  
Carbonation Depth ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Ordinary Concrete ◽  
Fly Ash Concrete ◽  
Carbonation Process

The accelerated carbonation test was carried out for the ordinary concrete and fly ash concrete. Influences of water-cement ratio, carbonation age and fly ash content on pH value were researched. The results show that carbonation depth, including incomplete carbonized zone, can be effectively reduced by reducing water-cement ratio. So lower water-cement ratio means high performance of resistance of carbonate. The use of fly ash can optimize concrete pore morphology, it’s beneficial for anti-carbonation. However, It disadvantageous to anti-carbonation because of less carbonation material. By taking appropriate mixture of fly ash we can not only enhance the anti-carbonation ability of concrete, but also reduce the use of cement to get well economic benefits.

Microscopic Mechanism of the Diffusivity of Concrete Chloride Ion

2013 ◽  
Vol 773 ◽  
pp. 687-692 ◽  
Author(s):  
Jun Liu ◽  
Feng Xing ◽  
Bi Qing Dong
Keyword(s):  
Fly Ash ◽  
Early Stage ◽  
Great Influence ◽  
Chloride Ion ◽  
Test Method ◽  
Mineral Admixture ◽  
Microscopic Mechanism ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
The Impact

Use concrete specimens with different mix proportions to conserve them for 90d taking into account the influence of mineral admixture material---fly ash. Then adopts the RCM test method to measure the rapid diffusivity of chloride ion of concrete and observes the microstructure of the cement paste using the SEM (scanning electron microscopy), aiming to study the impact of fly ash on its hydration process. The results show that the micro-pore structure of the concrete has a great influence on the rapid diffusivity of chloride ion, while its diffusivity is closely related with the water-cement ratio of concrete; after the fly ash is added, the ettringite generation of the concrete in the early stage decreases, and the interspace of the transition zone between the hydrated particles and hydration slurry is enlarged, coupled with the increase in the intercommunicating pore; after curing for 90d, the chloride ion diffusivity decreases significantly with the increase in the dosage of fly ash. For the concrete with the fly ash dosage of 15%, its chloride ion diffusivity is only 75.4% of that with the same water-cement ratio; when its fly ash content is 30%, its chloride ion diffusivity is only 32.3% of the ordinary concrete.

Survey on Factors Affecting Impermeability of Waterproof Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 1320-1323
Author(s):  
Yi Jin Li ◽  
Yun Li Gong ◽  
Jian Yin
Keyword(s):  
Fly Ash ◽  
Ash Content ◽  
Raw Material ◽  
Factors Affecting ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Mix Proportion

This paper describes the influence of raw material, water-cement ratio, sand ratio, cement-sand ratio and fly ash content on impermeability of waterproof concrete. The value ranges of several important mix parameters are summarized, that provides the reference to select the parameters of mix proportion of waterproof concrete for subway.

Effect of silica fume on durability of concrete composites containing fly ash

2013 ◽  
Vol 20 (1) ◽  
pp. 57-65 ◽  
Author(s):  
Peng Zhang ◽  
Qing-fu Li
Keyword(s):  
Fly Ash ◽  
Silica Fume ◽  
Shrinkage Strain ◽  
Carbonation Depth ◽  
Freeze Thaw ◽  
Slump Flow ◽  
Carbonation Resistance ◽  
Dry Shrinkage ◽  
Shrinkage Property ◽  
Durability Of Concrete

AbstractIn this paper, the effect of silica fume on the workability and durability of concrete composites containing fly ash, including water impermeability, dry shrinkage property, carbonation resistance and freeze-thaw resistance, are presented. Four different silica fume contents (3%, 6%, 9% and 12%) were used. The results indicate that the addition of silica fume has greatly improved the durability of water impermeability, the carbonation resistance and the freeze-thaw resistance of the concrete composites containing fly ash. With the increase in silica fume content, the length of water permeability and the carbonation depth of the specimens decrease gradually, and the relative dynamic elastic modulus of the specimens has a tendency to increase. However, the addition of silica fume has a little adverse effect on the workability and dry shrinkage property of concrete composites containing fly ash. With the increase in silica fume content, both the slump and the slump flow decrease gradually, and the dry shrinkage strain increases gradually.

Experiment Research on Plastic Strength of Grouting Materials of Desulfurization Denitration Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2093-2096
Author(s):  
Hong Hai Zhang ◽  
Ai Min Gong ◽  
Chun Yan Wang
Keyword(s):  
Fly Ash ◽  
Silicon Powder ◽  
Calculation Formula ◽  
Experiment Research ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Plastic Strength ◽  
Two Factors ◽  
Grouting Materials

Derived calculation formula of plastic strength, and used mortar consistency instrument to determine plastic strength. Through experiment, the fly ash and silicon powder that desulfurized or denitrated as grouting materials, its change rules of plastic strength were studid under different water cement ratio and different dosage conditions. Results shows that, between the two factors of water cement ratio and dosage, the water cement ratio affect significantly the plastic strength. The smaller the water cement ratio, the more obvious the increase of the plastic strength as time growth. Early plastic strength of silicon powder grouts is growing rapidly.

Study of Sleeper Concrete early Strength Based on Orthogonal Experiment

2013 ◽  
Vol 448-453 ◽  
pp. 1316-1320
Author(s):  
Hai Chao Wang ◽  
Ke Qiu ◽  
Shu Ling Gao
Keyword(s):  
Fly Ash ◽  
Design Method ◽  
Orthogonal Experiment ◽  
Orthogonal Design ◽  
Steam Curing ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Early Strength ◽  
The Difference ◽  
Railway Sleeper

Using orthogonal design method of four factors and three levels, make a mix ratio experiment on sleeper concrete of China's railway sleepers, used steam curing concrete early compressive strength (stripping strength) as evaluation index. Study on different experimental factors of water-cement ratio, sand ratio, fly ash and admixture differently influenced on the early strength of sleeper concrete and analyze the difference impact of each factor and level for the orthogonal experiment. The result shows that the admixture is the main factor for early strength of concrete, followed by fly ash, water-cement ratio and sand ratio. It can provide technical guidance for railway sleeper field and has practical value.

Laboratory Experimental Research on Mix Ratio Test of Cement Soil

2013 ◽  
Vol 438-439 ◽  
pp. 197-201
Author(s):  
Xian Hua Yao ◽  
Peng Li ◽  
Jun Feng Guan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Ratio Test ◽  
Curing Time ◽  
Curing Conditions ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Cement Soil

Based on the generalization and analysis of laboratory experimental results on mix ratio, the effects of various factors such as cement content, water-cement ratio, curing time, curing conditions and types of cement on the mechanical properties of unconfined compressive strength of cement soil are presented. Results show that the unconfined compressive strength of cement soil increases with the growing curing time, and it is greatly affected by the cement content, water-cement ratio, cement types and curing time, while the effect of curing conditions is weak with a cement content of more than 10%. Moreover, the stress-strain of the cement soil responds with the cement content and curing time, increasing curing time and cement content makes the cement soil to be harder and brittle, and leads to a larger Young's modulus.

Research of Performance of Low Amount of Cement Manufactured-Sand Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1200-1205
Author(s):  
Chun Hui Yu ◽  
Gu Hua Li ◽  
Jin Liang Gao ◽  
Qun Wei ◽  
Da Zhen Xu
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Grain Shape ◽  
Great Influence ◽  
Cementitious Materials ◽  
Natural Sand ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Manufactured Sand

Compared with natural sand, manufactured-sand is of small porosity, poor grain shape and graded, which impacts mixes workability and the properties after hardening. In Concrete, playing the role of retaining moisture water is mainly powder, including cement, powder in the sand and fly ash etc. The amount of powder has a great influence on the properties of concrete, especially on its workability. This paper mainly discusses the influence of amount of cement, cementitious materials, fly ash, water-cement ratio and other factors on the workability, compressive strength and shrinkage of concrete. The experiments show that, in the case of the low amount of cement, workability of the manufactured-sand concrete mixture, compressive strength and shrinkage deformation of test block all meet the actual requirements.

Sign in / Sign up

Export Citation Format

Share Document