Experimental and Numerical Study on Seismic Performance of Flat Columns under Bilateral Cyclic Loading

2013 ◽  
Vol 302 ◽  
pp. 347-354
Author(s):  
Ze Feng Ma ◽  
Zhou Dao Lu ◽  
Jiang Tao Yu ◽  
Zi Hong Cai
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
Numerical Study ◽  
Width Ratio ◽  
Finite Element Program ◽  
Static Tests ◽  
Element Program ◽  
Energy Dissipation Capacity ◽  
Shape Curve

In order to research seismic behavior of flat columns under bilateral cyclic loading with different angles, pseudo-static tests are conducted, which includes three 1:2 scaled flat columns. The height-width ratio of the column section is 5. And the loading directions are 00, 250 and 450 respectively. By observation of the test phenomenon and analysis of the data, the seismic performance of the columns including stiffness, skeleton curves, hysteresis curves, ductility and energy dissipation are obtained. Moreover, finite element program ANSYS is employed to simulate the bearing capacity of specimens. The research shows that with the loading angles increasing from 0 to 45, the strength of the flat column decreased gradually, while the ductility and energy dissipation capacity increase, and the failure mode changed from compression-shear to compression-bending. P-Δ effect becomes evident at lager values of loading angle. The compression-shearing curve of flat column complies with a heart-shape curve.

Experimental Study on Seismic Performance of the Reinforced Concrete Grid-Mesh Frame Wall

2013 ◽  
Vol 680 ◽  
pp. 234-238
Author(s):  
Jin Li Qiao ◽  
Wen Ling Tian ◽  
Ming Jie Zhou ◽  
Fang Lu Jiang ◽  
Kun Zhao
Keyword(s):  
Experimental Study ◽  
Reinforced Concrete ◽  
Energy Dissipation ◽  
Bearing Capacity ◽  
Seismic Performance ◽  
Seismic Energy ◽  
Width Ratio ◽  
Filling Material ◽  
Energy Dissipation Capacity ◽  
Grid Mesh

In order to validate the seismic performance of reinforced concrete grid-mesh frame wall , four grid frame walls in half size is made with different height-width ratios and different grid forms in the paper. Two of them are filling with cast-in-place plaster as filling material. According to the experimental results of these four walls subjected to horizontal reciprocating loads, we know that the grid-mesh frame wall's breaking form are in stages and multiple modes, and the main influencing factors are height-width ratio and grid form, what's more, with cast-in-place plaster as fill material, could not only improve the level of the wall bearing capacity and stiffness, but also improve the ductility and seismic energy dissipation capacity.

scholarly journals Experimental Study on Cumulative Damage Behavior of Steel-Reinforced Concrete Columns

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Lianjie Jiang ◽  
Guoliang Bai
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Bearing Capacity ◽  
Ground Motions ◽  
Peak Load ◽  
Cumulative Damage ◽  
Stiffness Degradation ◽  
Static Tests ◽  
Steel Ratio ◽  
Energy Dissipation Capacity

The cumulative damage behavior of SRC columns under far-field long-period ground motions was simulated and studied by quasi-static tests with the same displacement for 10 times. Quasi-static tests of 8 SRC columns were conducted under the horizontal cyclic loading with the same displacement for 10 times or 3 times, and then the effects of steel ratio, stirrup ratio, axial compression ratio, and number of cyclic loading on the cumulative damage of SRC columns under the far-field long-period ground motions were studied. The results showed that the number of cyclic loading had little effect on the peak load of the specimens, but had a significant effect on the deformation capacity, stiffness degradation, and energy dissipation capacity. Compared with the specimens after 3 cycles, the displacement ductility coefficient of specimens after 10 cycles was reduced by about 20%–26%, the ultimate hysteresis energy dissipation was reduced by 35%–48%, while the stiffness degradation rate was accelerated. After the peak load, the cumulative damage caused by multiple cyclic loading with the same displacement was more significant, which aggravated the reduction of bearing capacity and stiffness degradation. The smaller the steel ratio and stirrup ratio, the larger the axial compression ratio, and the greater the reduction of the bearing capacity and stiffness of specimens. However, accumulated damage caused by multiple cyclic loading with the same displacement had a slight impact on the energy dissipation capacity. Increasing the steel ratio and stirrup ratio can effectively improve the deformation capacity and energy dissipation capacity of the specimens and reduce the bearing capacity and stiffness degradation caused by cumulative damage.

Experimental Research on the Influence of the Pile Type and Stirrup on the Seismic Performance of PHC Piles

2012 ◽  
Vol 256-259 ◽  
pp. 2079-2084 ◽  
Author(s):  
Tie Cheng Wang ◽  
An Gao ◽  
Hai Long Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
High Strength ◽  
Loading Tests ◽  
Energy Dissipation Capacity ◽  
Pile Type ◽  
Cyclic Loading Tests ◽  
Reversed Cyclic

The influence of the pile type and the stirrup on the seismic performance was evaluated based on the results of reversed cyclic loading tests on the four prestressed high strength concrete (PHC) piles. It is indicated that the AB-type pile has the better seismic performance than the A-type pile from the results. The bearing capacity does not increase obviously with decreasing of the stirrup spacing and increasing of the stirrup diameter. The degradation of stiffness does not decrease significantly with decreasing of the stirrup spacing and increasing of the stirrup diameter. The energy dissipation capacity is improved with increasing of the stirrup diameter and decreasing of the stirrup spacing.

Seismic performance of concrete walls reinforced by high-strength bars: cyclic loading test and numerical simulation

2021 ◽  
Author(s):  
Xiangyong Ni ◽  
Shuangyin Cao ◽  
Hassan Aoude
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
Numerical Study ◽  
Shear Walls ◽  
High Strength ◽  
Test Results ◽  
3D Fem ◽  
Seismic Behaviour ◽  
Loading Test

This study examines the influence of cross-section shape on the seismic behaviour of high-strength steel reinforced concrete shear walls (HSS-RC) designed with Grade HRB 600 MPa reinforcement. As part of the study, two flexure-dominant walls with rectangular and T-shaped cross-sections, are tested under reversed cyclic loading. Seismic performance is evaluated by studying the failure characteristics, hysteretic curves, energy dissipation, ductility and reinforcing bar strains in the two walls. As part of the numerical study, two-dimensional (2D) and three-dimensional (3D) finite element modelling (FEM) are used to predict the seismic response of the rectangular and T-shaped walls, respectively. The test results show that compared to the rectangular wall, the flange in the T-shaped HSS-RC wall increased strength, energy dissipation and stiffness, but decreased ductility. The analytical hysteretic curves calculated using 2D and 3D FEM analyses show good agreement with the experimental test results.

scholarly journals Seismic Performance of RC Beam-Column Connections with Continuous Rectangular Spiral Transverse Reinforcements for Low Ductility Classes

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Mohammadamin Azimi ◽  
Azlan Bin Adnan ◽  
Abdul Rahman Bin Mohd Sam ◽  
Mahmood Md Tahir ◽  
Iman Faridmehr ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Numerical Methods ◽  
Seismic Performance ◽  
Brittle Failure ◽  
Rc Beam ◽  
Seismic Behaviour ◽  
Simultaneous Application ◽  
Lateral Resistance ◽  
Energy Dissipation Capacity

The seismic performance of RC columns could be significantly improved by continuous spiral reinforcement as a result of its adequate ductility and energy dissipation capacity. Due to post-earthquake brittle failure observations in beam-column connections, the seismic behaviour of such connections could greatly be improved by simultaneous application of this method in both beams and columns. In this study, a new proposed detail for beam to column connection introduced as “twisted opposing rectangular spiral” was experimentally and numerically investigated and its seismic performance was compared against normal rectangular spiral and conventional shear reinforcement systems. In this study, three full scale beam to column connections were first designed in conformance with Eurocode (EC2-04) for low ductility class connections and then tested by quasistatic cyclic loading recommended by ACI Building Code (ACI 318-02). Next, the experimental results were validated by numerical methods. Finally, the results revealed that the new proposed connection could improve the ultimate lateral resistance, ductility, and energy dissipation capacity.

Comparing the Seismic Performance of Beam-Column Joints with and without SFRC when Subjected to Cyclic Loading

2012 ◽  
Vol 626 ◽  
pp. 85-89 ◽  
Author(s):  
Kay Dora Abdul Ghani ◽  
Nor Hayati Hamid
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
Experimental Work ◽  
Concrete Beam ◽  
Steel Fiber ◽  
Precast Concrete ◽  
Experimental Results ◽  
Column Joint ◽  
Initial Cracks

The experimental work on two full-scale precast concrete beam-column corner joints with corbels was carried out and their seismic performance was examined. The first specimen was constructed without steel fiber, while second specimen was constructed by mixed up steel fiber with concrete and placed it at the corbels area. The specimen were tested under reversible lateral cyclic loading up to ±1.5% drift. The experimental results showed that for the first specimen, the cracks start to occur at +0.5% drifts with spalling of concrete and major cracks were observed at corbel while for the second specimen, the initial cracks were observed at +0.75% with no damage at corbel. In this study, it can be concluded that precast beam-column joint without steel fiber has better ductility and stiffness than precast beam-column joint with steel fiber. However, precast beam-column joint with steel fiber has better energy dissipation and fewer cracks at corbel as compared to precast beam-column joint without steel fiber.

PRELIMINARY STUDY ON NOVEL BEAM-TO-COLUMN CONNECTION BASED ON SMA PLATE

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Michael CH Yam ◽  
Ke Ke ◽  
Ping Zhang ◽  
Qingyang Zhao
Keyword(s):  
Friction Coefficient ◽  
Energy Dissipation ◽  
Numerical Study ◽  
Numerical Models ◽  
Numerical Technique ◽  
The Self ◽  
Hysteretic Behavior ◽  
The Novel ◽  
Energy Dissipation Capacity ◽  
Preliminary Study

A novel beam-to-column connection equipped with shape memory alloy (SMA) plates has been proposed to realize resilient performance under low-to-medium seismic actions. In this conference paper, the detailed 3D numerical technique calibrated by the previous paper is adopted to examine the hysteretic behavior of the novel connection. A parametric study covering a reasonable range of parameters including the thickness of the SMA plate, friction coefficient between SMA plate and beam flange and pre-load of the bolt was carried out and the influence of the parameters was characterized. In addition, the effect of the SMA Belleville washer on the connection performance was also studied. The results of the numerical study showed that the initial connection stiffness and the energy-dissipation capacity of the novel connection can be enhanced with the increase of the thickness of the SMA plate. In addition, the initial connection stiffness and energy-dissipation behavior of the novel connection can be improved by increasing the friction coefficient or pre-load of bolts, whereas the increased friction level could compromise the self-centering behavior of the connection. The hysteretic curves of the numerical models of the connection also implied that the SMA washers may contribute to optimizing the connection behavior by increasing the connection stiffness and energy-dissipation capacity without sacrificing the self-centering behavior.

Experimental study on seismic performance of suspended ceiling components

2021 ◽  
Author(s):  
Yong Wang ◽  
Huanjun Jiang ◽  
Chen Wu ◽  
Zihui Xu ◽  
Zhiyuan Qin
Keyword(s):  
Experimental Study ◽  
Energy Dissipation ◽  
Seismic Performance ◽  
Seismic Vulnerability ◽  
Axial Loading ◽  
Deformation Capacity ◽  
Severe Damage ◽  
Strong Earthquakes ◽  
Static Tests ◽  
Load Carrying

<p>Suspended ceiling systems (SCSs) experienced severe damage during strong earthquakes that occurred in recent years. The capacity of the ceiling component is a crucial factor affecting the seismic performance of SCS. Therefore, a series of static tests on suspended ceiling components under monotonic and cyclic loadings were carried out to investigate the seismic performance of the ceiling components. The ceiling components include main tee splices, cross tee latches and peripheral attachments. All specimens were tested under axial loading. Additionally, the static tests of cross tee latches subjected to shear and bending loadings were performed due to their seismic vulnerability. The failure pattern, load-carrying ability, deformation capacity and energy dissipation of the ceiling components are presented in detail in this study.</p>

Performance of parking steel column damaged by fire

2019 ◽  
Vol 10 (2) ◽  
pp. 138-154
Author(s):  
Farshid Masoumi ◽  
Ebrahim Farajpourbonab
Keyword(s):  
Cyclic Loading ◽  
Seismic Performance ◽  
Numerical Study ◽  
Mechanical Analysis ◽  
Content Type ◽  
Steel Columns ◽  
Fire Engineering ◽  
Steel Column ◽  
Concrete Coating ◽  
Fire Loading

Purpose The primary purpose of this research was to expand the knowledge base regarding the behavior of steel columns during exposure to fire. This paper presents the numerical study of the effect of heat on the performance of parking steel column in a seven-story steel building under cyclic loading. Design/methodology/approach In this research, the forces and deformations developed during a fire are estimated by using detailed 3D finite-element models. The analyses are in the form of a coupled thermo-mechanical analysis in two types of loading: concurrent loading (fire and cyclic loading) and non-concurrent loading (first fire and then cyclically), and the analyses have been conducted in both states of the fire loading with cooling and without cooling using the ABAQUS software. Further, it was investigated whether, during the fire loading, the specimen was protected by a 3-cm-thick concrete coating and how much it changes the seismic performance. After verification of the specimen with the experimental test results, the column model was investigated under different loading conditions. Findings The result of analyses indicates that the effect of thermal damage on the performance of steel columns, when cooling is happening late, is more than the state in which cooling occurs immediately after the fire. In this paper, thermal–seismic performance of parking steel columns has been specified and the effect of the fire damage has been investigated for the protected steel by concrete coating and to the non-protected steel, under both cooling and non-cooling states. Originality/value This study led to recommendations based on the findings and suggestions for additional work to support performance-based fire engineering. It is clear that predicting force and deformation on steel column during fire is complex and it is affected by many variables. Here in this paper, those variables are examined and proper results have been achieved.

Sign in / Sign up

Export Citation Format

Share Document