The Control Technology of Pressure Vessel In-Service Quality Inspection

2013 ◽  
Vol 437 ◽  
pp. 700-704
Author(s):  
Xue Rong Ma
Keyword(s):  
Service Quality ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Control Technology ◽  
Quality Inspection ◽  
Test Results ◽  
Optimization Scheme ◽  
Test Tank ◽  
Comprehensive Test ◽  
The Cost

Aiming at the comprehensive inspection of pressure vessels in service, put forward the original test results as the basis, realize the optimization scheme of comprehensive test, the possibility is to a minimum missing caused in pressure vessel that the crack (defects) are greater than the critical, so as to ensure the safety of the structure at the same time, the workload and the cost is reduced to the lowest. Through the test tank group, this method is proved to be feasible.

Tensile Plastic Instability of Axisymmetric Pressure Vessels

1998 ◽  
Vol 120 (1) ◽  
pp. 6-11 ◽  
Author(s):  
D. P. Updike ◽  
A. Kalnins
Keyword(s):  
Pressure Vessel ◽  
Detrimental Effect ◽  
Cylindrical Shells ◽  
Plastic Instability ◽  
Pressure Vessels ◽  
Reduction Factor ◽  
Test Results ◽  
Strength Reduction Factor ◽  
Burst Data ◽  
Longitudinal Welds

This paper examines the calculated pressure at a tensile plastic instability of a pressure vessel and its relationship to burst test results. It is proposed that the instability pressure be accepted as an upper bound to the pressure at which a vessel bursts, and that a strength reduction factor be used to predict the burst. The paper also presents a suitable mathematical model for the calculation of the instability pressures for thin-walled axisymmetric vessels. The proposition is tested by applying the model to a pressurized diaphragm, four cylindrical shells, and two torispherical heads, for which experimental burst data are available. It is found that the ratio of the test burst pressure to the calculated pressure at the tensile plastic instability, expressed in percent, ranges from 71 to 96 percent. The highest ratio occurs for a pressurized diaphragm with no significant defects. The lowest ratios occur for cylindrical shells with longitudinal welds, suggesting that the presence of the welds had a detrimental effect on the burst strength. These results may be useful when designing a pressure vessel with respect to its ultimate strength.

Risk Based Inspection Planning for Deteriorating Pressure Vessels

2016 ◽  
Author(s):  
Shane Haladuick ◽  
Markus R. Dann
Keyword(s):  
Decision Analysis ◽  
Decision Maker ◽  
Pressure Vessel ◽  
Oil And Gas ◽  
Pressure Vessels ◽  
Inspection Planning ◽  
Course Of Action ◽  
Inspection Data ◽  
The Cost ◽  
Aid Decision

Pressure vessels are subject to deterioration processes, such as corrosion and fatigue. If left unchecked these deterioration processes can lead to failure; therefore, inspections and repairs are performed to mitigate this risk. Oil and gas facilities often have regular scheduled shutdown periods during which many components, including the pressure vessels, are disassembled, inspected, and repaired or replaced if necessary. The objective of this paper is to perform a decision analysis to determine the best course of action for an operator to follow after a pressure vessel is inspected during a shutdown period. If the pressure vessel is inspected and an unexpectedly deep corrosion defect is detected an operator has two options: schedule a repair for the next shutdown period, or perform an immediate unscheduled repair. A scheduled repair is the preferred option as it gives the decision maker lead time to accommodate the added labour and budgetary requirements. This preference is accounted for by a higher cost of immediate unscheduled repairs relative to the cost of a scheduled repair at the next shutdown. Depending on the severity of deterioration either option could present the optimal course of action. In this framework the decision that leads to the minimum expected cost is selected. A stochastic gamma process was used to model the future deterioration growth using the historical inspection data, considering the measurement error and uncertain initial wall thickness, to determine the probability of pressure vessel failure. The decision analysis framework can be used to aid decision makers in deciding when a repair or replacement action should be performed. This method can be used in real time decision making to inform the decision maker immediately post inspection. A numerical example of a corroding pressure vessel illustrates the method.

Paris Fatigue Life Modeling of Pressure Vessel Service Simulation Tests

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
John H. Underwood ◽  
John J. Keating ◽  
Edward Troiano ◽  
Gregory N. Vigilante
Keyword(s):  
Fatigue Life ◽  
Residual Stresses ◽  
Pressure Vessel ◽  
Base Alloy ◽  
Pressure Vessels ◽  
Full Scale ◽  
Test Results ◽  
X Ray Diffraction ◽  
Life Model ◽  
Nickel Base

Results from four groups of full-scale pressure vessel service simulation tests are described and analyzed using Paris fatigue life modeling. The objective is to determine how the vessel and initial crack configurations and applied and residual stresses control the as-tested fatigue life of the vessel. The tube inner radii are in the 40–80 mm range; wall thickness varies from 6 to 80 mm; materials are ASTM A723 pressure vessel steel and IN718 nickel-base alloy; applied internal pressure varies from 90 to 700 MPa. The Paris constant, C, and exponent, m, that describe the fatigue crack propagation rate versus stress intensity factor range for the various vessel materials, were measured as part of the investigation. Extensive, previously published fatigue life results from baseline A723 pressure vessels with well characterized autofrettage residual stresses and C and m values are used to demonstrate that a Paris fatigue life model gives a good description of the measured life. The same model is then used to determine the variables with predominant control over life in three types of pressure vessel for which less information and tests results are available. A design life for pressure vessels is calculated for a specified very low probability of fatigue failure using the log(N)-normal distribution statistics often used for fatigue of structures. The results of the work showed: (i) X-ray diffraction measurements of through-wall autofrettage residual stresses are in excellent agreement with prior neutron diffraction measurements from a baseline autofrettaged A723 pressure vessel; these verified autofrettage residual stresses then provide critical input to the baseline Paris life modeling; (ii) comparison of the various full-scale fatigue test results with results from the Paris fatigue life model shows close agreement when autofrettage residual stresses are incorporated into models; (iii) model results for A723 steel vessels with yield strength reduced from the initial 1400 MPa value and degree of autofrettage increased from the initial 40% value indicates a significantly improved resistance to brittle failure with no loss of fatigue life; (iv] comparison of model fatigue life results for IN718 nickel-base alloy vessels with their full-scale test results is improved when near-bore residual stresses measured by X-ray diffraction are included in the model calculations.

Finite Element Investigation of Bauschinger Effect in High-Strength A723 Pressure Vessel Steel

2006 ◽  
Vol 128 (2) ◽  
pp. 185-189 ◽  
Author(s):  
Edward Troiano ◽  
John H. Underwood ◽  
Anthony P. Parker
Keyword(s):  
Finite Element ◽  
Pressure Vessel ◽  
Bauschinger Effect ◽  
High Strength ◽  
Pressure Vessels ◽  
Pressure Vessel Steel ◽  
Test Results ◽  
Vessel Steel ◽  
Reverse Yielding ◽  
The Difference

The Bauschinger effect has been evaluated in high-strength pressure vessels. A simple initial test suggested that a biaxial Bauschinger effect was present and that it was different from previously published uniaxial Bauschinger results. The difference was believed to be significant, so further investigation was undertaken. Several full-size A723 steel gun sections were heavily overstrained and subjected to slit tests in order to measure opening angles and displacements. These geometries were then modeled with finite element (FE) analysis using both ideal autofrettage stresses and Bauschinger modified stresses, which were based on previously published uniaxial Bauschinger test results. Because techniques available for predicting reverse yielding for overstrained pressure vessels were limited, a simple methodology for predicting the yield surface upon reverse yielding from a series of uniaxial Bauschinger test data was developed and is presented. This methodology, when used in the FE predictions, compares favorably with analytical predictions made previously. Comparisons of slit-opening results measured from pressure vessel sections with FE calculations using uniaxial Bauschinger data are made. The opening displacements comparison between the uniaxial predictions and those measured from the heavily overstrained sections with biaxial stresses are so subtle (<1mm) that the tests appear to be inconclusive.

Stress Field Around a Large Opening in a Pressure Vessel During a Major Repair

2009 ◽  
Author(s):  
Erik Garrido ◽  
Euro Casanova
Keyword(s):  
Pressure Vessel ◽  
New Technologies ◽  
Mechanical Design ◽  
General Purpose ◽  
Pressure Vessels ◽  
Mechanical Equipment ◽  
Stress Distributions ◽  
Large Opening ◽  
Von Mises ◽  
Case Basis

It is a regular practice in the oil industry to modify mechanical equipment to incorporate new technologies and to optimize production. In the case of pressure vessels, it is occasionally required to cut large openings in their walls in order to have access to the interior part of the equipment for executing modifications. This cutting process produces temporary loads, which were obviously not considered in the original mechanical design. Up to now, there is not a general purpose specification for approaching the assessments of stress levels once a large opening in a vertical pressure vessel has been made. Therefore stress distributions around large openings are analyzed on a case-by-case basis without a reference scheme. This work studies the distribution of the von Mises equivalent stresses around a large opening in FCC Regenerators during internal cyclone replacement, which is a frequently required practice for this kind of equipment. A finite element parametric model was developed in ANSYS, and both numerical results and illustrating figures are presented.

Effect of Carbide Content on Temper Embrittlement of 2.25Cr1Mo Steel

2016 ◽  
Author(s):  
Yian Wang ◽  
Guoshan Xie ◽  
Zheng Zhang ◽  
Xiaolong Qian ◽  
Yufeng Zhou ◽  
...  
Keyword(s):  
High Temperature ◽  
Pressure Vessel ◽  
High Stress ◽  
Temper Embrittlement ◽  
Damage Mechanism ◽  
Pressure Vessels ◽  
Nondestructive Method ◽  
Operating Conditions ◽  
Low Alloy Steels ◽  
Carbide Content

Temper embrittlement is a common damage mechanism of pressure vessels in the chemical and petrochemical industry serviced in high temperature, which results in the reduction of roughness due to metallurgical change in some low alloy steels. Pressure vessels that are temper embrittled may be susceptible to brittle fracture under certain operating conditions which cause high stress by thermal gradients, e.g., during start-up and shutdown. 2.25Cr1-Mo steel is widely used to make hydrogenation reactor due to its superior combination of high mechanical strength, good weldability, excellent high temperature hydrogen attack (HTHA) and oxidation-resistance. However, 2.25Cr-1Mo steel is particularly susceptible to temper embrittlement. In this paper, the effect of carbide on temper embrittlement of 2.25Cr-1Mo steel was investigated. Mechanical properties and the ductile-brittle transition temperature (DBTT) of 2.25Cr-1Mo steel were measured by tensile test and impact test. The tests were performed at two positions (base metal and weld metal) and three states (original, step cooling treated and in-service for a hundred thousand hours). The content and distribution of carbides were analyzed by scanning electron microscope (SEM). The content of Cr and Mo elements in carbide was measured by energy dispersive X-ray analysis (EDS). The results showed that the embrittlement could increase the strength and reduce the plasticity. Higher carbide contents appear to be responsible for the higher DBTT. The in-service 2.25Cr-1Mo steel showed the highest DBTT and carbide content, followed by step cooling treated 2.25Cr-1Mo steel, while the as-received 2.25Cr-1Mo steel has the minimum DBTT and carbide content. At the same time, the Cr and Mo contents in carbide increased with the increasing of DBTT. It is well known that the specimen analyzed by SEM is very small in size, sampling SEM specimen is convenient and nondestructive to pressure vessel. Therefore, the relationship between DBTT and the content of carbide offers a feasible nondestructive method for quantitative measuring the temper embrittlement of 2.25Cr-1Mo steel pressure vessel.

A Study on Fatigue Life Evaluation of Pressure Vessel Made of ASME SA240-316L Material Using Numerical Analysis

2019 ◽  
Vol 893 ◽  
pp. 1-5 ◽  
Author(s):  
Eui Soo Kim
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Pressure Vessel ◽  
Life Prediction ◽  
Pressure Vessels ◽  
Physical Damage ◽  
Element Analysis ◽  
Internal Damage ◽  
Life Evaluation ◽  
Fatigue Life Evaluation

Pressure vessels are subjected to repeated loads during use and charging, which can causefine physical damage even in the elastic region. If the load is repeated under stress conditions belowthe yield strength, internal damage accumulates. Fatigue life evaluation of the structure of thepressure vessel using finite element analysis (FEA) is used to evaluate the life cycle of the structuraldesign based on finite element method (FEM) technology. This technique is more advanced thanfatigue life prediction that uses relational equations. This study describes fatigue analysis to predictthe fatigue life of a pressure vessel using stress data obtained from FEA. The life prediction results areuseful for improving the component design at a very early development stage. The fatigue life of thepressure vessel is calculated for each node on the model, and cumulative damage theory is used tocalculate the fatigue life. Then, the fatigue life is calculated from this information using the FEanalysis software ADINA and the fatigue life calculation program WINLIFE.

Fatigue and Burst Analysis of Hy-140(T) Steel Pressure Vessels

1970 ◽  
Vol 92 (1) ◽  
pp. 11-16 ◽  
Author(s):  
J. M. Barsom ◽  
S. T. Rolfe
Keyword(s):  
Yield Strength ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
High Yield ◽  
Corrosion Properties ◽  
Burst Analysis

Increasing use of high-strength steels in pressure-vessel design has resulted from emphasis on decreasing the weight of pressure vessels for certain applications. To demonstrate the suitability of a 140-ksi yield strength steel for use in unwelded pressure vessels, HY-140(T)—a quenched and tempered 5Ni-Cr-Mo-V steel—was fabricated and subjected to various burst and fatigue tests, as well as to various laboratory tests. In general, results of the investigation indicated very good tensile, Charpy, Nil Ductility Transition Temperature (NDT), low-cycle fatigue, and stress-corrosion properties of HY-140(T) steels, as well as very good burst tests results, in comparison with existing high-yield strength pressure-vessel steels. The results also indicate that the HY-140(T) steel should be an excellent material for its originally designed purpose, Naval hull applications.

Failure Probability Assessment for a Boiling Water Reactor Pressure Vessel Under Low Temperature Over-Pressure Event

2012 ◽  
Author(s):  
Hsoung-Wei Chou ◽  
Chin-Cheng Huang ◽  
Bo-Yi Chen ◽  
Hsien-Chou Lin ◽  
Ru-Feng Liu
Keyword(s):  
Low Temperature ◽  
Failure Probability ◽  
Pressure Vessel ◽  
Fracture Probability ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Boiling Water ◽  
Boiling Water Reactor ◽  
Water Reactor ◽  
Reactor Pressure

The fracture probability of a boiling water reactor pressure vessel for a domestic nuclear power plant in Taiwan has been numerically analyzed using an advanced version of ORNL’s FAVOR code. First, a model of the vessel beltline region, which includes all shell welds and plates, is built for the FAVOR code based on the plant specific parameters of the reactor pressure vessel. Then, a novel flaw model which describes the flaw types of surface breaking flaws, embedded weld flaws and embedded plate flaws are simulated along both inner and outer vessel walls. When conducting the fracture probability analyses, a transient low temperature over-pressure event, which has previously been shown to be the most severe challenge to the integrity of boiling water reactor pressure vessels, is considered as the loading condition. It is found that the fracture occurs in the fusion-line area of axial welds, but with only an insignificant failure probability. The low through-wall cracking frequency indicates that the analyzed reactor pressure vessel maintains sufficient stability until either the end-of-license or for doubling of the present license of operation.

Mechanical Behavior of Ti-6Al-4V Manufactured by Electron Beam Additive Fabrication

2013 ◽  
Author(s):  
Leila Ladani ◽  
Lalit Roy
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Lead Time ◽  
Aerospace Industry ◽  
Tensile Tests ◽  
Test Results ◽  
Great Resistance ◽  
Additive Fabrication ◽  
Anisotropy Effect ◽  
The Cost

Additive Layer Fabrication, in particular Electron Beam Additive Fabrication (EBAF), has recently drawn much attention for its special usability to fabricate intricately designed parts as a whole. It not only increases the production rate which reduces the production lead time but also reduces the cost by minimizing the amount of waste material to a great extent. Ti6Al4V is the most common type of material that is currently being fabricated using EBAF technique. This material has been used in aerospace industry for several reasons such as excellent mechanical properties, low density, great resistance to corrosion, and non-magnetism. The effects of build direction of layers (namely, addition of layers along one of the x, y & z directions with respect to the build table) and the anisotropy effect caused by it has not been explored vigorously. This anisotropy effect has been investigated in this work. Different mechanical properties such as Yield Strength (YS), Ultimate Tensile Strength (UTS), and Modulus of Elasticity (E) of these three types of Ti6Al4V are determined using tensile tests and are compared with literature. The tensile test results show that YS and UTS for flat-build samples have distinguishably higher values than those of the side-build and top-build samples.

Sign in / Sign up

Export Citation Format

Share Document