Effect of Material Constitution on the Properties of Thermal Insulation Materials

2014 ◽  
Vol 541-542 ◽  
pp. 141-145
Author(s):  
Bo Liu ◽  
Shou De Wang ◽  
Shuai Yang ◽  
Chen Chen Gong ◽  
Ling Chao Lu
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Cementitious Materials ◽  
Cellulose Ether ◽  
Dry Density ◽  
Ratio Test ◽  
Insulation Material ◽  
Material Constitution ◽  
Insulation Materials

Cement-based foam insulation board is a lightweight thermal insulation and have a characteristic of energy saving. The effects of material constitution on the properties of mechanical properties, dry densityand thermal conductivity for thermal insulation materials. The subject of fast hardening sulphoaluminate cement as cementitious materials, polystyrene particles as a lightweight thermal insulation material, adding a certain amount of water reducer, cellulose ethers, air entraining agent to make thermal insulation materials. The experimental results shows that the appropriate material constitution is following: the cement-bead ratio is 12, the ratio is 0.65, the water-cement ratio is 0.4, the content of water reducer is 0.5%, the content of cellulose ether is 0.4%, the content of the air entraining agent is 0.4% .This mix ratio test of mechanical properties are: flexural strength is 0.72MPa, compressive strength is 1.24MPa, dry density is 375kg/m3, water content is 2.3%, water absorption is 10.8%, softening coefficient is 0.95 and coefficient of thermal conductivity is 0.053 W/ (m K).

scholarly journals Analysis of new inorganic exterior insulation materials and thermal energy storage

2020 ◽  
Vol 24 (5 Part B) ◽  
pp. 3195-3203
Author(s):  
Jianying Wang
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Insulation ◽  
Glass Bead ◽  
Water Retention ◽  
Raw Materials ◽  
Retention Rate ◽  
Cellulose Ether ◽  
Dry Density ◽  
Insulation Materials

In order to reduce the energy efficiency of the construction industry and improve the building safety, in this research, a new type of inorganic insulation material ? vitreous bead insulation mortar is studied and its properties are analyzed. Quantitative method is used to analyze the influence of glass bead mixing amount, cellulose ether mixing amount and redispersible emulsion powder mixing amount on the consistency, water retention rate, dry density, softening coefficient and compressive strength of glass bead insulation mortar. The effect of different raw materials allocation on the thermal conductivity of vitrified microbeads thermal insulation mortar is explored. The results show that the performance of insulation mortar decreases significantly with the increase of glass bubbles. With the increase of cellulose ether content, the consistency and compressive strength of insulation mortar first increased and then decreased, the water retention rate increased significantly, but the dry density decreased significantly. With the increase of the content of redispersible emulsion powder, the consistency and compressive strength of insulation mortar first increased and then decreased, but the dry density decreased gradually. Glass bubbles and fly ash parameters are the main factors that affect the thermal conductivity of thermal insulation mortar, and their thermal conductivity decreases with the increase of the proportion of air-entraining agent. As a result, the performance of vitreous microbeads thermal insulation mortar will change to a certain extent with the different proportion of raw materials, which provides data support for the preparation and application of inorganic external wall thermal insulation materials.

Cryogenic thermal insulating and mechanical properties of rigid polyurethane foams blown with hydrofluoroolefin: Effect of perfluoroalkane

2021 ◽  
pp. 0021955X2110626
Author(s):  
Tae Seok Kim ◽  
Yeongbeom Lee ◽  
Chul Hyun Hwang ◽  
Kwang Ho Song ◽  
Woo Nyon Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Stability ◽  
Cell Size ◽  
Thermal Insulation ◽  
Coefficient Of Thermal Expansion ◽  
Lower Surface ◽  
Polyurethane Foams ◽  
Insulation Material ◽  
Pu Foams

The effect of perfluoroalkane (PFA) on the morphology, thermal conductivity, mechanical properties and thermal stability of rigid polyurethane (PU) foams was investigated under ambient and cryogenic conditions. The PU foams were blown with hydrofluorolefin. Morphological results showed that the minimum cell size (153 μm) was observed when the PFA content was 1.0 part per hundred polyols by weight (php). This was due to the lower surface tension of the mixed polyol solution when the PFA content was 1.0 php. The thermal conductivity of PU foams measured under ambient (0.0215 W/mK) and cryogenic (0.0179 W/mK at −100°C) conditions reached a minimum when the PFA content was 1.0 php. The low value of thermal conductivity was a result of the small cell size of the foams. The above results suggest that PFA acted as a nucleating agent to enhanced the thermal insulation properties of PU foams. The compressive and shear strengths of the PU foams did not appreciably change with PFA content at either −170°C or 20°C. However, it shows that the mechanical strengths at −170°C and 20°C for the PU foams meet the specification. Coefficient of thermal expansion, and thermal shock tests of the PU foams showed enough thermal stability for the LNG carrier’s operation temperature. Therefore, it is suggested that the PU foams blown by HFO with the PFA addition can be used as a thermal insulation material for a conventional LNG carrier.

Effect of Operating Temperatures on Thermal Conductivity of Polystyrene Insulation Material: Impact on Envelope-Induced Cooling Load

2014 ◽  
Vol 564 ◽  
pp. 315-320 ◽  
Author(s):  
Maatouk Khoukhi ◽  
Mahmoud Tahat
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Energy Performance ◽  
Building Envelope ◽  
Insulation Material ◽  
Cooling Load ◽  
Thermal Insulation Material ◽  
Insulation Materials ◽  
Energy Performance Of Buildings ◽  
The Impact

The impact of the thermal conductivity (k-value) change of polystyrene insulation material in building envelope due to changes in temperature on the thermal and energy performance of a typical residential building under hot climate is investigated. Indeed, the thermal and energy performance of buildings depends on the thermal characteristics of the building envelope, and particularly on the thermal resistance of the insulation material used. The thermal insulation material which is determined by its thermal conductivity, which describes the ability of heat to flow cross the material in presence of a gradient of temperature, is the main key to assess the performance of the thermal insulation material. When performing the energy analysis or calculating the cooling load for buildings, we use published values of thermal conductivity of insulation materials, which are normally evaluated at 24°C according to the ASTM standards. In reality, thermal insulation in building is exposed to significant and continuous temperature variations, due essentially to the change of outdoor air temperature and solar radiation. Many types of insulation materials are produced and used in Oman, but not enough information is available to evaluate their performance under the prevailing climatic condition. The main objective of this study is to investigate the relationship between the temperature and thermal conductivity of various densities of polystyrene, which is widely used as building insulation material in Oman. Moreover, the impact of thermal conductivity variation with temperature on the envelope-induced cooling load for a simple building model is discussed. This work will serve as a platform to investigate the effect of the operating temperature on thermal conductivity of other building material insulations, and leads to more accurate assessment of the thermal and energy performance of buildings in Oman.

Possibilities of Using Natural Fibres for Production of Particular Insulation for Use in Civil Engineering

2015 ◽  
Vol 1124 ◽  
pp. 111-116
Author(s):  
Martina Reif ◽  
Jitka Peterková ◽  
Jiri Zach
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Civil Engineering ◽  
Research Work ◽  
Natural Fibers ◽  
Cellulose Fibers ◽  
Natural Fibres ◽  
Insulation Materials ◽  
Bast Fibers

The paper deals with the development options of particular insulation based on a blend of recycled cellulose fibers and natural (mainly) bast fibers. The paper presents the results of research work in the field of addiction thermal insulation, acoustic and mechanical properties of experimentally produced insulators on density..Keywords: Natural fibers, thermal conductivity, insulation materials, straw, fibreboard, cellulose fibers

Environmentally Friendly Cellular Concrete for Wall Insulation

2013 ◽  
Vol 539 ◽  
pp. 271-275 ◽  
Author(s):  
Ya Qing Jiang ◽  
Jun Yang ◽  
Yun Chen
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mass Density ◽  
Polypropylene Fiber ◽  
Cementitious Materials ◽  
Dry Density ◽  
Insulation Material ◽  
Good Market ◽  
Cellular Concrete

Cellular concrete characterizes low mass density and low thermal conductivity is one of the durable and economic wall insulation materials which have good market prospects. The present paper investigated the composition of ternary cementitious materials, mixture design and production process of cellular concrete panel (CCP). Experimental results indicated that a higher compressive strength of CCP may be obtained by blended PⅡ52.5 Portland cement with pulverized low temperature clinker (PLWC) made of water treatment sludge and fly ash in the mass ratio of 0.70: 0.15: 0.15. CCP with dry density of 226 kg/m3, thermal conductivity of 0.056 W/ (m•K), compressive strength of 0.6 MPa and water absorption ratio of 7.6 vol. % was modified by high range water reducer, polypropylene fiber and water resistant agent. Mathematic models for controlling temperature of mixing water and for calculation quantity of gas forming admixture were established. Insulated moulds were specially designed for taking advantage of hydration heat of cement to speed up moulds turnover. Meanwhile, internal microcrack of CCP was avoided. CCP incorporating PLWC and fly ash may be used as external insulation material of walls.

scholarly journals Characterization of Thermal Bio-Insulation Materials Based on Oil Palm Wood: The Effect of Hybridization and Particle Size

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3287
Author(s):  
Indra Mawardi ◽  
Sri Aprilia ◽  
Muhammad Faisal ◽  
Samsul Rizal
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Particle Size ◽  
Water Absorption ◽  
Thermal Insulation ◽  
Oil Palm ◽  
Bending Strength ◽  
Fine Particles ◽  
Biomass Waste ◽  
Insulation Materials

Oil palm wood is the primary biomass waste produced from plantations, comprising up to 70% of the volume of trunks. It has been used in non-structural materials, such as plywood, lumber, and particleboard. However, one aspect has not been disclosed, namely, its use in thermal insulation materials. In this study, we investigated the thermal conductivity and the mechanical and physical properties of bio-insulation materials based on oil palm wood. The effects of hybridization and particle size on the properties of the panels were also evaluated. Oil palm wood and ramie were applied as reinforcements, and tapioca starch was applied as a bio-binder. Panels were prepared using a hot press at a temperature of 150 °C and constant pressure of 9.8 MPa. Thermal conductivity, bending strength, water absorption, dimensional stability, and thermogravimetric tests were performed to evaluate the properties of the panels. The results show that hybridization and particle size significantly affected the properties of the panels. The density and thermal conductivity of the panels were in the ranges of 0.66–0.79 g/cm3 and 0.067–0.154 W/mK, respectively. The least thermal conductivity, i.e., 0.067 W/mK, was obtained for the hybrid panels with coarse particles at density 0.66 g/cm3. The lowest water absorption (54.75%) and thickness swelling (18.18%) were found in the hybrid panels with fine particles. The observed mechanical properties were a bending strength of 11.49–18.15 MPa and a modulus of elasticity of 1864–3093 MPa. Thermogravimetric analysis showed that hybrid panels had better thermal stability than pure panels. Overall, the hybrid panels manufactured with a coarse particle size exhibited better thermal resistance and mechanical properties than did other panels. Our results show that oil palm wood wastes are a promising candidate for thermal insulation materials.

Study on Polyurethane Foam Insulation Materials

2014 ◽  
Vol 563 ◽  
pp. 41-47
Author(s):  
Zhang Lu ◽  
Dan Xia ◽  
Zhen An
Keyword(s):  
Mechanical Properties ◽  
Polyurethane Foam ◽  
Thermal Insulation ◽  
Nucleating Agent ◽  
Insulation Material ◽  
Foam Material ◽  
Thermal Insulation Material ◽  
Insulation Materials ◽  
Best Value ◽  
Stannous Octoate

The foaming reaction so that all water-gel reaction and foaming reaction to reach equilibrium, the excellent thermal insulation material was prepared by the regulation of the catalyst, a nucleating agent and an isocyanate. By experiment we know that the amount of stannous octoate catalyst 6%, 4% of the amount of nucleating agent CaCO3, and the case of 100% of the amount of isocyanate, the density of the foam material and the mechanical properties of the insulation material to achieve the best value.

Study on Preparation and Properties of Cement-Based Foamed Lightweight Thermal Insulation Material

2011 ◽  
Vol 306-307 ◽  
pp. 994-997
Author(s):  
Cong Cong Jiang ◽  
Guo Zhong Li ◽  
Shui Zhang
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Thermal Insulation ◽  
Thermal Conductivity Coefficient ◽  
Steel Slag ◽  
Activation Mechanism ◽  
Dry Density ◽  
Insulation Material ◽  
Thermal Insulation Material

A cement-based foamed lightweight thermal insulation material was prepared with cement, industrial waste (fly ash, steel slag) as the main raw materials, by using self-developed composite activator and foaming agent. The influence of foam content on dry density, compressive strength and thermal conductivity coefficient of material was studied, the activation mechanism of composite activator to fly ash and steel slag was discussed. Results showed that, the dry density and compressive strength of material decreased, and thermal conductivity coefficient decreased first and then increased with the increasing foam content.

Robust and superhydrophobic thiourethane bridged polysilsesquioxane aerogels as potential thermal insulation materials

2016 ◽  
Vol 4 (28) ◽  
pp. 10801-10805 ◽  
Author(s):  
Fangxin Zou ◽  
Peng Yue ◽  
Xinghua Zheng ◽  
Dawei Tang ◽  
Wenxin Fu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Sol Gel ◽  
Vacuum Drying ◽  
Drying Method ◽  
Low Thermal Conductivity ◽  
Insulation Materials ◽  
Sol Gel Process ◽  
Bridged Polysilsesquioxane

Novel thiourethane bridged polysilsesquioxane aerogels prepared by a sol–gel process and vacuum drying method exhibit extraordinary mechanical properties and low thermal conductivity.

Evaluation of Structure Influence on Thermal Conductivity of Thermal Insulating Materials from Renewable Resources

1970 ◽  
Vol 17 (2) ◽  
pp. 208-212 ◽  
Author(s):  
Jolanta VĖJELIENĖ ◽  
Albinas GAILIUS ◽  
Sigitas VĖJELIS ◽  
Saulius VAITKUS ◽  
Giedrius BALČIŪNAS
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Renewable Resources ◽  
Raw Materials ◽  
Raw Material ◽  
Barley Straw ◽  
Insulation Material ◽  
Insulating Materials ◽  
Insulation Materials ◽  
Thermal Insulating

The development of new thermal insulation materials needs to evaluate properties and structure of raw material, technological factors that make influence on the thermal conductivity of material. One of the most promising raw materials for production of insulation material is straw. The use of natural fibres in insulation is closely linked to the ecological building sector, where selection of materials is based on factors including recyclable, renewable raw materials and low resource production techniques In current work results of research on structure and thermal conductivity of renewable resources for production thermal insulating materials are presented. Due to the high abundance of renewable resources and a good its structure as raw material for thermal insulation materials barley straw, reeds, cattails and bent grass stalks are used. Macro- and micro structure analysis of these substances is performed. Straw bales of these materials are used for determining thermal conductivity. It was found that the macrostructure has the greatest effect on thermal conductivity of materials. Thermal conductivity of material is determined by the formation of a bale due to the large amount of pores among the stalks of the plant, inside the stalk and inside the stalk wall.http://dx.doi.org/10.5755/j01.ms.17.2.494

Sign in / Sign up

Export Citation Format

Share Document