Influence of Laser Cladding Parameters on γ-TiAl Coatings

2014 ◽  
Vol 698 ◽  
pp. 273-276
Author(s):  
Iuliia N. Maliutina ◽  
Hocine Si-Mohand ◽  
Romain Piolet
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
Laser Cladding ◽  
Structural Characteristics ◽  
Maximum Value ◽  
Powder Density

Relationships between laser cladding parameters (i.e. powder density) and structural characteristics as well as mechanical properties of γ-TiAl-based clads on titanium alloys were investigated. The conducted study revealed that the height of the formed clads increases linearly with powder density. The maximum value of microhardness corresponds to clad produced at the lowest powder density.

The Influence of Thermocyclic Treatment on the Structure and Mechanical Properties of Pseudo-Alpha Titanium Alloys for Steam Turbine Blades

2021 ◽  
Vol 1031 ◽  
pp. 117-124
Author(s):  
Vladimir Gadalov ◽  
Irina Vornacheva ◽  
Sergey Voinash ◽  
Vitaly Ignatenko ◽  
Evgeny Remshev
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
Structural Characteristics ◽  
Turbine Blades ◽  
Strength Properties ◽  
High Temperature Strength ◽  
Cycling Treatment ◽  
Thermocyclic Treatment ◽  
Alpha Titanium ◽  
Steam Turbine Blades

The influence of thermal cycling treatment of pseudo-α-titanium alloys OT4 and VT20 on their structural and substructural characteristics, as well as their mechanical properties is considered. A significant change in structural characteristics is established. This contributes to an increase in the strength properties of alloys with satisfactory ductility and high-temperature strength.

scholarly journals Modification of Mechanical Properties of High-Strength Titanium Alloys VT23 and VT23M Due to Impact-Oscillatory Loading

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 80 ◽  
Author(s):  
Mykola Chausov ◽  
Janette Brezinová ◽  
Andrii Pylypenko ◽  
Pavlo Maruschak ◽  
Liudmyla Titova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
High Strength ◽  
The Self ◽  
Self Organization ◽  
Two Phase ◽  
Rolled Metal ◽  
Technological Method ◽  
Equilibrium Processes ◽  
Production Conditions

A simple technological method is proposed and tested experimentally, which allows for the improvement of mechanical properties in sheet two-phase high-strength titanium alloys VT23 and VT23M on the finished product (rolled metal), due to impact-oscillatory loading. Under impact-oscillatory loading and dynamic non-equilibrium processes (DNP) are realized in titanium alloys, leading to the self-organization of the structure. As a result, the mechanical properties of titanium alloys vary significantly with subsequent loading after the realization of DNP. In this study, the test modes are found, which can be used in the production conditions.

scholarly journals Fabrication of Polycaprolactone/Nano Hydroxyapatite (PCL/nHA) 3D Scaffold with Enhanced In Vitro Cell Response via Design for Additive Manufacturing (DfAM)

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1394
Author(s):  
Yong Sang Cho ◽  
So-Jung Gwak ◽  
Young-Sam Cho
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Structural Characteristics ◽  
Structure Design ◽  
Compressive Modulus ◽  
Control Group ◽  
Design For Additive Manufacturing ◽  
3D Scaffold ◽  
3D Printed

In this study, we investigated the dual-pore kagome-structure design of a 3D-printed scaffold with enhanced in vitro cell response and compared the mechanical properties with 3D-printed scaffolds with conventional or offset patterns. The compressive modulus of the 3D-printed scaffold with the proposed design was found to resemble that of the 3D-printed scaffold with a conventional pattern at similar pore sizes despite higher porosity. Furthermore, the compressive modulus of the proposed scaffold surpassed that of the 3D-printed scaffold with conventional and offset patterns at similar porosities owing to the structural characteristics of the kagome structure. Regarding the in vitro cell response, cell adhesion, cell growth, and ALP concentration of the proposed scaffold for 14 days was superior to those of the control group scaffolds. Consequently, we found that the mechanical properties and in vitro cell response of the 3D-printed scaffold could be improved by kagome and dual-pore structures through DfAM. Moreover, we revealed that the dual-pore structure is effective for the in vitro cell response compared to the structures possessing conventional and offset patterns.

scholarly journals A Review on Microstructural Features and Mechanical Properties of Wheels/Rails Cladded by Laser Cladding

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 152
Author(s):  
Xinlin Wang ◽  
Lei Lei ◽  
Han Yu
Keyword(s):  
Mechanical Properties ◽  
Service Life ◽  
Process Optimization ◽  
Laser Cladding ◽  
Future Development ◽  
Heat Affected Zone ◽  
Small Deformation ◽  
Microstructural Characteristics ◽  
Low Input ◽  
Recent Developments

The service life of rails would be remarkably reduced owing to the increase of axle load, which can induce the occurrence of damages such as cracks, collapse, fat edges, etc. Laser cladding, which can enhance the mechanical properties of the rail by creating a coating, has received great attention in the area of the rails due to the attractive advantages such as low input heat, small heat-affected zone, and small deformation. In this paper, recent developments in the microstructural characteristics and mechanical properties of a cladded layer on the rail are reviewed. The method of process optimization for enhancing the properties of a cladded layer are discussed. Finally, the trend of future development is forecasted.

Structural characteristics and mechanical properties of Ti(Cr) films produced on Si substrate

2009 ◽  
Vol 517 (19) ◽  
pp. 5715-5721
Author(s):  
Fanhao Zeng ◽  
Xiang Xiong ◽  
Guodong Li ◽  
Boyun Huang
Keyword(s):  
Mechanical Properties ◽  
Structural Characteristics ◽  
Si Substrate

scholarly journals Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1954
Author(s):  
Yang Liu ◽  
Xun Zhang ◽  
Quanxin Gao ◽  
Hongliang Huang ◽  
Yongli Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Maleic Anhydride ◽  
Ag Nanoparticles ◽  
Decomposition Temperature ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Maximum Value ◽  
Polyolefin Elastomer ◽  
Local Defects

In the present study, silver (Ag) nanoparticles and maleic anhydride-grafted polyolefin elastomer (MAH-g-POE) were used as enhancement additives to improve the performance of the polyoxymethylene (POM) homopolymer. Specifically, the POM/Ag/MAH-g-POE ternary nanocomposites with varying Ag nanoparticles and MAH-g-POE contents were prepared by a melt mixing method. The effects of the additives on the microstructure, thermal stability, crystallization behavior, mechanical properties, and dynamic mechanical thermal properties of the ternary nanocomposites were studied. It was found that the MAH-g-POE played a role in the bridging of the Ag nanoparticles and POM matrix and improved the interfacial adhesion between the Ag nanoparticles and POM matrix, owing to the good compatibility between Ag/MAH-g-POE and the POM matrix. Moreover, it was found that the combined addition of Ag nanoparticles and MAH-g-POE significantly enhanced the thermal stability, crystallization properties, and mechanical properties of the POM/Ag/MAH-g-POE ternary nanocomposites. When the Ag/MAH-g-POE content was 1 wt.%, the tensile strength reached the maximum value of 54.78 MPa. In addition, when the Ag/MAH-g-POE content increased to 15wt.%, the elongation at break reached the maximum value of 64.02%. However, when the Ag/MAH-g-POE content further increased to 20 wt.%, the elongation at break decreased again, which could be attributed to the aggregation of excessive Ag nanoparticles forming local defects in the POM/Ag/MAH-g-POE ternary nanocomposites. Furthermore, when the Ag/MAH-g-POE content was 20 wt.%, the maximum decomposition temperature of POM/Ag/MAH-g-POE ternary nanocomposites was 398.22 °C, which was 71.39 °C higher than that of pure POM. However, compared with POM, the storage modulus of POM/Ag/MAH-g-POE ternary nanocomposites decreased with the Ag/MAH-g-POE content, because the MAH-g-POE elastomer could reduce the rigidity of POM.

Sign in / Sign up

Export Citation Format

Share Document