Effect of H2 and CO Content in Syngas on the Performance and Emission of Syngas-Diesel Dual Fuel Engine - A Review

2014 ◽  
Vol 699 ◽  
pp. 648-653 ◽  
Author(s):  
Bahaaddein K.M. Mahgoub ◽  
Suhaimi Hassan ◽  
Shaharin Anwar Sulaiman
Keyword(s):  
Carbon Monoxide ◽  
Diesel Engines ◽  
Combustion Process ◽  
Exhaust Emission ◽  
Dual Fuel ◽  
Pure Liquid ◽  
Compression Ignition ◽  
Performance And Emission ◽  
Combustion Duration ◽  
Combustible Gases

In this review, a series of research papers on the effects of hydrogen and carbon monoxide content in syngas composition on the performance and exhaust emission of compression ignition diesel engines, were compiled. Generally, the use of syngas in compression ignition (CI) diesel engine leads to reduce power output due to lower heating value when compared to pure liquid diesel mode. Therefore, variation in syngas composition, especially hydrogen and carbon monoxide (Combustible gases), is suggested to know the appropriate syngas composition. Furthermore, the simulated model of syngas will help to further explore the detailed effects of engine parameters on the combustion process including the ignition delay, combustion duration, heat release rate and combustion phasing. This will also contribute towards the efforts of improvement in performance and reduction in pollutants’ emissions from CI diesel engines running on syngas at dual fuel mode. Generally, the database of syngas composition is not fully developed and there is still room to find the optimum H2 and CO ratio for performance, emission and diesel displacement of CI diesel engines.

scholarly journals A dual-fuel compression ignition engine – distinctive features

2010 ◽  
Vol 141 (2) ◽  
pp. 33-39
Author(s):  
Sławomir LUFT
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Process ◽  
Diesel Oil ◽  
Gas Analysis ◽  
Exhaust Emission ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Spark Ignition Engines ◽  
Compression Ignition Engine ◽  
Distinctive Features

For many years in the Department of Automobiles and Internal Combustion Engines in Technical University of Radom there are carried out investigations on dual-fuel compression ignition engine in which the ignition is initiated by a pilot diesel oil dose and the applied main fuels have properties similar to those applied in spark ignition engines. The tested fuels were methanol, ethanol, LPG and natural gas. Analysis of the obtained results allowed to make some generalizations and to determine advantages as well as problems which should be solved for higher efficiency, power and durability. The paper will present information on efficiency, power, toxic exhaust emission and chosen parameters of combustion process of a dual-fuel compression ignition engine as well as on a difficult to control – knock combustion which may result in lower engine durability and piston crank mechanism failure.

scholarly journals Influence of Gasoline Addition on Biodiesel Combustion in a Compression-Ignition Engine with Constant Settings

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1499
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik
Keyword(s):  
Diesel Fuel ◽  
Ignition Delay ◽  
Combustion Process ◽  
Gasoline Fraction ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Combustion Duration ◽  
Fuel Technology

This paper presents results of investigation of co-combustion process of biodiesel with gasoline, in form of mixture and using dual fuel technology. The main objective of this work was to show differences in both combustion systems of the engine powered by fuels of different reactivity. This paper presents parameters of the engine and the assessment of combustion stability. It turns out that combustion process of biodiesel was characterized by lower ignition delay compared to diesel fuel combustion. For 0.54 of gasoline energetic fraction, the ignition delay increased by 25% compared to the combustion of the pure biodiesel, but for dual fuel technology for 0.95 of gasoline fraction it was decreased by 85%. For dual fuel technology with the increase in gasoline fraction, the specific fuel consumption (SFC) was decreased for all analyzed fractions of gasoline. In the case of blend combustion, the SFC was increased in comparison to dual fuel technology. An analysis of spread of ignition delay and combustion duration was also presented. The study confirmed that it is possible to co-combust biodiesel with gasoline in a relatively high energetic fraction. For the blend, the ignition delay was up to 0.54 and for dual fuel it was near to 0.95.

scholarly journals Electronic control unit development and emissions evaluation for hydrogen–diesel dual-fuel engines

2018 ◽  
Vol 10 (12) ◽  
pp. 168781401881407
Author(s):  
Yasin Karagöz ◽  
Majid Mohammad Sadeghi
Keyword(s):  
Diesel Engines ◽  
Working Condition ◽  
Electronic Control Unit ◽  
Control Unit ◽  
Dual Fuel ◽  
Hydrogen Energy ◽  
Compression Ignition ◽  
Electronic Control ◽  
Fuel System ◽  
Compression Ignition Engines

In this study, it was aimed to operate today’s compression ignition engines easily in dual-fuel mode with a developed electronic control unit. Especially, diesel engines with mechanical fuel system can be easily converted to common-rail fuel system with a developed electronic control unit. Also, with this developed electronic control unit, old technology compression ignition engines can be turned into dual-fuel mode easily. Thus, thanks to the flexibility of engine maps to be loaded into the electronic control unit, diesel engines can conveniently be operated with alternative gas fuels and diesel dual fuel. In particular, hydrogen, an alternative, environmentally friendly, and clean gas fuel, can easily be used with diesel engines by pilot spraying. Software and hardware development of electronic control unit are made, in order to operate a diesel engine with diesel+hydrogen dual fuel. Finally, developed electronic control unit was reviewed on 1500 r/min stable engine speed on different hydrogen energy rates (0%, 15%, 30%, and 45% hydrogen) according to thermic efficiency and emissions (CO, total unburned hydrocarbons, NOx, and smoke), and apart from NOx emissions, a significant improvement has been obtained. There was no increased NOx emission on 15% hydrogen working condition; however, on 45% hydrogen working condition, a dramatic increase arose.

scholarly journals Quantitative analysis of combustion process of marine dual fuel engine under the framework of iconology

2021 ◽  
Vol 9 (4B) ◽  
Author(s):  
Hongliang Yu ◽  
◽  
Weiwei Wang ◽  
Shulin Duan ◽  
Peiting Sun ◽  
...  
Keyword(s):  
Combustion Process ◽  
Image Feature ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Flame Velocity ◽  
Combustion Duration ◽  
Engine Cylinder ◽  
Characteristic Values ◽  
Feature Values ◽  
Logical Mapping

The methane (CH4) burning interruption factor and the characteristic values characterizing the flame combustion state in the engine cylinder were defined. The logical mapping relationship between image feature values and combustion conditions in the framework of iconology was proposed. Results show that there are two periods of combustion instability and combustion stability during the combustion of dual fuel. The high temperature region with a cylinder temperature greater than 1800K is the largest at 17°CA after top dead center (TDC), accounting for 73.25% of the combustion chamber area. During the flame propagation, the radial flame velocity and the axial flame velocity are “unimodal” and “wavy,” respectively. During the combustion process, the CH4 burning interruption factor first increased and then decreased. The combustion duration in dual fuel mode is 21.25°CA, which is 15.5°CA shorter than the combustion duration in pure diesel mode.

An integrated effort of medium reactivity fuel, in-cylinder, and after-treatment strategies to demonstrate potential reduction in challenging emissions of reactivity controlled compression ignition combustion

2019 ◽  
Vol 234 (5) ◽  
pp. 1260-1278
Author(s):  
R Murugan ◽  
D Ganesh ◽  
G Nagarajan
Keyword(s):  
Carbon Monoxide ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Oxidation Catalyst ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Potential Reduction ◽  
Carbon Monoxide Emission ◽  
Compression Ignition Combustion

Previous studies on reactivity controlled compression ignition combustion indicated that, reducing the hydrocarbon and carbon monoxide emissions at low load conditions still remains a challenge because of lower in-cylinder temperatures due to lower global reactivity gradient and reduced oxidation process. Research in this direction has not been reported so far and with this motivation, an attempt has been made to increase the global reactivity gradient and oxidation of fuel–air mixture by converting the low reactivity fuel methanol into medium reactivity fuel. This is achieved by mixing high octane oxygenated fuel, methanol (Octane Number: 110), with an oxygenated better cetane and volatility fuels like polyoxymethylene dimethyl ether (Cetane Number: 78) and isobutanol (Cetane Number: 15). The medium reactivity fuel with multiple direct injection of diesel fuel timed the combustion of dual fuel–air mixture to avoid too late or too advanced combustion which are the prime factors in controlling the unburnt emissions in a low temperature combustion process. Four medium reactivity fuel samples, M80IB20, M60IB40, M90P10, and M80P20, on percentage volume basis have been prepared and tested on the modified on-road three-cylinder turbocharged common rail direct injection diesel engine to demonstrate higher indicated thermal efficiency and potential reduction in unburnt and oxides of nitrogen/particulate matter emissions from reactivity controlled compression ignition combustion. Experimental results show that, use of medium reactivity fuel with optimized diesel injection strategy resulted in 66% decrease in hydrocarbon emission and 74% decrease in carbon monoxide emission by enhancing the oxidation of fuel–air mixture at lower temperatures which is evidently noticed in the combustion characteristics. Further reduction in hydrocarbon and carbon monoxide emission of about 90% has been achieved by integrating the diesel oxidation catalyst with the engine.

scholarly journals An Experimental Study on the Performance and Emission of the diesel/CNG Dual-Fuel Combustion Mode in a Stationary CI Engine

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3857 ◽  
Author(s):  
Arkadiusz Jamrozik ◽  
Wojciech Tutak ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Fuel ◽  
Carbon Dioxide Emissions ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Stable Operation ◽  
Performance And Emission ◽  
Ci Engine

One of the possibilities to reduce diesel fuel consumption and at the same time reduce the emission of diesel engines, is the use of alternative gaseous fuels, so far most commonly used to power spark ignition engines. The presented work concerns experimental research of a dual-fuel compression-ignition (CI) engine in which diesel fuel was co-combusted with CNG (compressed natural gas). The energy share of CNG gas was varied from 0% to 95%. The study showed that increasing the share of CNG co-combusted with diesel in the CI engine increases the ignition delay of the combustible mixture and shortens the overall duration of combustion. For CNG gas shares from 0% to 45%, due to the intensification of the combustion process, it causes an increase in the maximum pressure in the cylinder, an increase in the rate of heat release and an increase in pressure rise rate. The most stable operation, similar to a conventional engine, was characterized by a diesel co-combustion engine with 30% and 45% shares of CNG gas. Increasing the CNG share from 0% to 90% increases the nitric oxide emissions of a dual-fuel engine. Compared to diesel fuel supply, co-combustion of this fuel with 30% and 45% CNG energy shares contributes to the reduction of hydrocarbon (HC) emissions, which increases after exceeding these values. Increasing the share of CNG gas co-combusted with diesel fuel, compared to the combustion of diesel fuel, reduces carbon dioxide emissions, and almost completely reduces carbon monoxide in the exhaust gas of a dual-fuel engine.

Experimental Investigation of Performance and Emission Parameters Changes on Diesel Engines Using Anisole Additive

2014 ◽  
Vol 490-491 ◽  
pp. 987-991
Author(s):  
Mustafa Kaan Baltacioğlu ◽  
Kadi̇r Aydin ◽  
Ergül Yaşar ◽  
Hüseyi̇n Turan Arat ◽  
Çağlar Conker ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Nitrogen Oxide ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Gas Emissions ◽  
Performance And Emission

In this study, effect of anisole additive into the diesel fuel on performance and emission parameters of diesel engines was investigated. Instead of structural changes which are more difficult and expensive, development of fuel technologies is preferred to provide reduction on exhaust gas emissions which are harmful to environment and human health. Therefore, in this experimental study, anisole was used as additive into diesel fuel with the volumetric ratio of 1,5%, 3% and 5%. The performance characteristics and exhaust emissions of a four cylinder, four stroke, naturally aspirated, water cooled, direct injection compression ignition engine fueled with modified fuels were analyzed. Engine was subjected constant speed, full load conditions during tests. Engine power, torque, specific fuel consumption, carbon monoxide, nitrogen oxide and carbon dioxide emissions were measured and results were evaluated. Changes in performance parameters were negligible for all ratios of modified fuels except specific fuel consumption. Finally, while carbon monoxide gas emissions were increased with anisole additive, carbon dioxide and nitrogen oxide gas emissions were decreased.

Effect of Intake Charge Preheating and Equivalence Ratio in a Dual Fuel Diesel Engine Run on Biogas and Ethanol-Blended Diesel

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Achinta Sarkar ◽  
Ujjwal K. Saha
Keyword(s):  
Carbon Monoxide ◽  
Equivalence Ratio ◽  
Dual Fuel ◽  
Emission Characteristics ◽  
Maximum Torque ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Gaseous Fuels ◽  
Efficient Combustion ◽  
Overall Performance

Dual fuel diesel (DFD) engines have been gaining popularity due to the flexibility of using both bio and fossil liquid and gaseous fuels. Further, the efficient combustion in DFD mode with bio liquid and gaseous fuel can greatly reduce the greenhouse gas emissions as well as the dependency on fossil diesel. In recent times, a host of investigation has been done in normal dual fuel diesel (nDFD) mode with pure diesel and biogas. However, the engines with ethanol blended with diesel and intake charge (biogas–air mixture) with preheating have not been studied. In the present study, 5% ethanol blended with diesel (E5) and biogas with preheating are used in dual fuel engine (DFD-E5) to find their performance and emission characteristics. In order to have a direct comparison of performances, an engine with pure diesel (E0) and biogas with preheating is also tested in dual fuel mode (DFD-E0). In all the cases, the effect of total equivalence ratio on engine overall performance has also been investigated. In DFD-E5 mode, and at the maximum torque of 21.78 N·m, the brake thermal efficiency (BTE) increases by 2.98% as compared to nDFD mode. At the same torque, there is no trace of carbon monoxide (CO), whereas there is a reduction of hydrocarbon (HC) emission by 62.22% with respect to pure diesel (PD) mode. The nitrogen of oxides (NOx) is found to decrease in DFD modes in contrast to PD mode.

Sign in / Sign up

Export Citation Format

Share Document