Effect of Ethylene Vinyl Axetate (EVA) on the Mechanical Properties of Low-Density Polyethylene/EVA Blends

2019 ◽  
Vol 889 ◽  
pp. 223-230
Author(s):  
Thi Hong Nga Pham ◽  
Thi My Hoa Le ◽  
Xiao Wei Zhang
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Bending Strength ◽  
Charpy Impact ◽  
Molding Compounds ◽  
Major Significance ◽  
Extensive Range ◽  
Plastic Industry ◽  
The Cost ◽  
Charpy Impact Strength

The extensive range of fillers used nowadays indicated the major significance of filler in the plastic industry. Although their original purpose was to lower the cost of the molding compounds; prime importance is now attached to selective modification of the properties of a specific plastic. In this study, the examples of LDPE/EVA blends, were put into 0, 3, 6, 9, 12 and 15 wt.% of EVA. The tensile strength, bending strength and impact strength of samples were determined according to ASTM D638, ISO 178 and ISO 179. Results showed that when increasing ratio of EVA in LDPE/ EVA blends, tensile strength decreased from 10.9 MPa to 8.6 MPa. Bending strength decreased linearly from 9.63 MPa to 5.46 MPa. Charpy impact strength decreased from 47.5 kJ/m2 to 6.3 kJ/m2. On the contrary, elongation in 100% LDPE is 78.3%; with the appearance of EVA, elongation of the LDPE/ EVA blends increased upto 109.1%. In addition, SEM micrographs indicated that, it was more crystal-clear when the EVA content is less; in the highest EVA content with 15%, it can be seen that the specimen after pressing is slightly opaque and darker than the orthers. From that showed the addition of EVA to the polymer leads the tensile strength, bending strength were not affect much, impact strength decreased but elongation experienced an increase.

Effect of inorganic pigments on the properties of coextruded polypropylene-based composites

2016 ◽  
Vol 31 (1) ◽  
pp. 23-33 ◽  
Author(s):  
Svetlana Butylina ◽  
Ossi Martikka ◽  
Timo Kärki
Keyword(s):  
Tensile Strength ◽  
Iron Oxide ◽  
Impact Strength ◽  
Water Immersion ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Immersion Test ◽  
Accelerated Weathering ◽  
Inorganic Pigments ◽  
Charpy Impact Strength

In this article, the effect of the incorporation of three inorganic pigments on the properties of coextruded polypropylene-based composites was studied. Three different pigments were incorporated in the shell layer of the composites: iron oxide, titanium dioxide (TiO2) and zinc oxide (ZnO). The tensile properties and Charpy impact strength of the composites were tested. A water immersion test was conducted. The morphology of the fractured surfaces of composites was characterised by scanning electron microscopy. The durability of the composites was assessed by testing colour characteristics and tensile strength after 500 hours of accelerated weathering. The results revealed that the TiO2-containing composite had the highest tensile modulus and Charpy impact strength, while the ZnO-containing composite had the lowest tensile strength and Charpy impact strength. Iron oxide was found to have no effect on either the physical or mechanical properties of the composite. The porosity of composites influences their water absorption and thickness swelling. The TiO2-containing composite exhibited better colour stability.

scholarly journals Mechanical Properties of Abaca Fiber Reinforced Urea Formaldehyde Composites

2015 ◽  
Vol 12 (1) ◽  
pp. 54-59 ◽  
Author(s):  
Abhishek Suvarna ◽  
Akash Katagi ◽  
Jackson Pasanna ◽  
Sunil Kumar ◽  
Basavaraju Bennehalli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Urea Formaldehyde ◽  
Charpy Impact ◽  
Fiber Reinforced ◽  
Compression Moulding ◽  
Charpy Impact Strength

The present investigation focuses on the fabrication and mechanical characterization of alkali treated natural abaca fiber reinforced urea formaldehyde composites. The composites were prepared by means of compression moulding, and then the effects of fiber loading on mechanical properties such as tensile strength, flexural strength and impact strength were investigated. The composite with 40 wt% abaca fibers gave excellent tensile strength and flexural strength showing that it has the most superior bonding and adhesion of all the composites. In particular, the highest value, 10.02 kJ/m2 of charpy impact strength is observed in the composite with 50 wt% abaca fiber. This work revealed the potential of using abaca fibers in fiberboard.

scholarly journals The effect of the accelerated aging on the mechanical properties of the PMMA denture base materials modified with itaconates

2011 ◽  
Vol 65 (6) ◽  
pp. 707-715 ◽  
Author(s):  
Pavle Spasojevic ◽  
Milorad Zrilic ◽  
Dragoslav Stamenkovic ◽  
Sava Velickovic
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Testing Machine ◽  
Base Material ◽  
Accelerated Aging ◽  
Charpy Impact ◽  
Accelerated Ageing ◽  
Denture Base ◽  
Elongation At Break ◽  
Charpy Impact Strength

This study evaluated the effect of accelerated ageing on the tensile strength, elongation at break, hardness and Charpy impact strength in commercial PMMA denture base material modified with di-methyl itaconate (DMI) and di-n-butyl itaconate (DBI). The samples were prepared by modifying commercial formulation by addition of itaconates in the amounts of 2.5, 5, 7.5 and 10% by weight. After polymerization samples were characterized by FT-IR and DSC analysis while residual monomer content was determined by HPLC-UV. Accelerated ageing was performed at 70?C in water for periods of 7, 15 and 30 days. Tensile measurements were performed using Instron testing machine while the hardness of the polymerized samples was measured by Shore D method. The addition of itaconate significantly reduces the residual MMA. Even at the small amounts of added itaconates (2.5%) the residual MMA content was reduced by 50%. The increase of itaconate content in the system leads to the decrease of residual MMA. It has been found that the addition of di-n-alkyl itaconates decreases the tensile strength, hardness and Charpy impact strength and increases elongation at break. Samples modified with DMI had higher values of tensile strength, hardness and Charpy impact strength compared to the ones modified with DBI. This is explained by the fact that DBI has longer side chain compared to DMI. After accelerated ageing during a 30 days period the tensile strength decreased for all the investigated samples. The addition of DMI had no effect on the material ageing and the values for the tensile strength of all of the investigated samples decreased around 20%, while for the samples modified with DBI, the increase of the amount of DBI in the polymerized material leads to the higher decrease of the tensile strength after the complete accelerated ageing period od 30 days, aulthough after the first seven days of the accelerated ageing the values of hardness have increased for all of the investigated samples. Such behavior is explained as the result of the polymer chain relaxation. The values of Charpy impact strength decreased after accelerated ageing. The amount of added DMI have no affect on the decrease of Charpy impact strength after accelerated ageing, the decrease was similar as for pure PMMA. The decrease of Charpy impact strength increased as the amount of added DBI increases.

scholarly journals Improving Mechanical Properties of PLA/Starch Blends Using Masterbatch Containing Vegetable Oil Based Active Ingredients

Polymers ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2981
Author(s):  
Bianka Nagy ◽  
Norbert Miskolczi ◽  
Zoltán Eller
Keyword(s):  
Impact Strength ◽  
Vegetable Oil ◽  
Rapeseed Oil ◽  
Flexural Modulus ◽  
Charpy Impact ◽  
Sem Images ◽  
Elongation At Break ◽  
Starch Concentration ◽  
Starch Blends ◽  
Charpy Impact Strength

The aim of this research was to increase the compatibility between PLA and starch with vegetable oil-based additives. Based on tensile results, it can be stated, that Charpy impact strength could be improved for 70/30 and 60/40 blends in both unconditioned and conditioned cases, regardless of vegetable oil, while no advantageous change in impact strength was obtained with PLA-g-MA. Considering sample with the highest starch concentration (50%), the flexural modulus was improved by using sunflower oil-based additive, Charpy impact strength and elongation at break was increased using rapeseed oil-based additive in both conditioned and unconditioned cases. SEM images confirmed the improvement of compatibility between components.

scholarly journals Effect of Gamma Radiation on the Mechanical Properties of Natural Fabric Reinforced Polyester Composites

2019 ◽  
Vol 27 (4(136)) ◽  
pp. 88-93
Author(s):  
K.Z.M. Abdul Motaleb ◽  
Md Shariful Islam ◽  
Rimvydas Milašius
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Gamma Radiation ◽  
Bending Strength ◽  
Polyester Resin ◽  
Radiation Doses ◽  
Elongation At Break ◽  
Bending Modulus ◽  
Polyester Composites

Two types of composites:(1) pineapple fabric reinforced polyester resin (Pineapple/PR) and (2) jute fabric reinforced polyester resin (Jute/PR) were prepared and the mechanical properties investigated for various gamma radiation doses ranging from 100-500 krad. Properties like tensile strength, Young’s modulus, elongation-at-break, bending strength, bending modulus and impact strength were increased significantly by 19%, 32%, 45%, 32%, 47% and 20%, respectively, at a dose of 300 krad for Pineapple/PR, and by 47%, 49%, 42%, 45%, 52% and 65%, respectively, at a dose of 200 krad for the Jute/PR composite in comparison to the non-irradiated composite. Gamma radiation improved the mechanical properties, but overdoses of radiation even caused a reduction in them.

Eco-Friendly Composites Based on Bitter Tea Oil Meal and Polylactic Acid

2021 ◽  
Vol 889 ◽  
pp. 21-26
Author(s):  
Yeng Fong Shih ◽  
Jia Yi Xu ◽  
Nian Yi Wu ◽  
Yu Ting Chiu ◽  
Hui Ming Yu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Food Industry ◽  
Impact Resistance ◽  
Experimental Results ◽  
Polybutylene Succinate ◽  
The Cost

Bitter tea oil meal (BTOM) is the main waste from the production of bitter tea oil which is squeezed from bitter tea seeds. The purpose of this study is to reuse the BTOM as an additive of the polylactic acid (PLA) to prepare eco-friendly composites. The effects of the addition of BTOM and maleic anhydride grafted polybutylene succinate (MAPBS) on the properties of PLA were investigated. The addition of MAPBS is mainly to increase the toughness of the PLA, and to increase the compatibility between BTOM and PLA. The experimental results show that the compatibility of PLA and BTOM and impact resistance of the composites can be improved by addition of MAPBS. The composite with 5% BTOM and 8% MAPBS exhibited the best tensile strength. In addition, the composite with 5% BTOM and 5% MAPBS has the best impact strength. It was found that the addition of BTOM and MAPBS can promote the crystallization of PLA. Moreover, the addition of BTOM not only can reduce the usage of PLA and the cost of the materials, but also reuse and reduce the waste from food industry.

The Effect of Scandium on the Mechanical Properties of A356 Aluminium Alloy

2016 ◽  
Vol 707 ◽  
pp. 144-147
Author(s):  
Ying Pio Lim ◽  
Wei Hong Yeo ◽  
A. Masita
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloy ◽  
Die Casting ◽  
A356 Alloy ◽  
Charpy Impact ◽  
Casting Process ◽  
Die Casting Process ◽  
Charpy Impact Strength ◽  
A356 Aluminium Alloy

In this project, the addition of scandium (Sc) into A356 aluminium alloy was studied for its effect on the mechanical properties after gravity die casting process. Scandium addition was administered at the weight percentages of 0.1, 0.2 and 0.3. The results obtained in this work revealed that scandium can significantly enhance the mechanical properties of A356 alloy in terms of tensile strength, hardness and charpy impact strength. In general, the addition of 0.2 wt% Sc in A356 alloy was found to be able to achieve the maximum tensile strength of 172.94MPa as compared to 136.03MPa for sample without Sc. No significant improvement in tensile strength was found when more than 0.3wt% added to the alloy. As for hardness, the sample with 0.3 wt% Sc attained the maximum Vicker’s hardness of 86.60 HV as compared to 76.48 HV for unmodified A356. Similarly, the addition of 0.3wt% Sc in A356 can achieve highest impact energy of 2.71J as compare to 1.09J for unmodified A356.

scholarly journals An Experimental Study on the Effect of Nanomaterials and Fibers on the Mechanical Properties of Polymer Composites

Buildings ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 7
Author(s):  
Chanachai Thongchom ◽  
Nima Refahati ◽  
Pouyan Roodgar Saffari ◽  
Peyman Roudgar Saffari ◽  
Meysam Nouri Niyaraki ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Modulus Of Elasticity ◽  
Graphene Nanosheets ◽  
Charpy Impact ◽  
Tensile Tests ◽  
Basalt Fibers ◽  
Low Weight ◽  
Internal Mixer ◽  
The Impact

This study aims to explore the tensile and impact properties (tensile strength, modulus of elasticity, and impact strength) of polypropylene (PP)-based nanocomposites reinforced with graphene nanosheets, nanoclay, and basalt fibers. The response surface methodology (RSM) with Box–Behnken design (BBD) was adopted as the experimental design. An internal mixer was used to prepare compounds consisting of 0, 0.75 and 1.5 wt% graphene nanosheets, 0, 10 and 20 wt% basalt fibers, and 0, 3 and 6 wt% nanoclay. The samples were prepared by a hot press machine for mechanical testing. The tensile tests were run to determine the tensile strength, and modulus of elasticity, and the Charpy impact tests were performed to assess the impact strength. It was found that the addition of basalt increased the tensile strength, modulus of elasticity, and impact strength by 32%, 64% and 18%, respectively. Also, the incorporation of the low-weight graphene nanosheets increased the tensile and impact strength by 15% and 20%, respectively, Adding graphene nanosheets generally improved the modulus of elasticity by 66%. Similarly, the addition of nanoclay improved the tensile strength by 17% and increased the modulus of elasticity by 59%, but further addition of it decreased the impact strength by 19%. The values obtained by this experiment for the mechanical property were roughly close to the data yielded from desirability optimization.

Sign in / Sign up

Export Citation Format

Share Document