Effect of Humidity on the Thermal Stability of Red Pyrotechnic Composition

2014 ◽  
Vol 1030-1032 ◽  
pp. 52-55
Author(s):  
Shuo Shi ◽  
Lin Shuang Zhao
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Peak Temperature ◽  
Thermal Decomposition Mechanism ◽  
Thermal Safety ◽  
Pyrotechnic Mixture ◽  
Pyrotechnic Composition ◽  
Pyrotechnic Mixtures ◽  
Thermal Stability Of

pyrotechnic mixtures are sensitivity with the influence of humidity and are susceptible to explosive decompositions. The aim of this paper is to provide thermal decomposition data under different humidity conditions. The method of TG-DSC simultaneous analysis has been used to study the thermal decomposition mechanism of a typical red pyrotechnic mixture. The kinetic parameters were calculated by kissinger method. The thermal stability is evaluated by decomposition peak temperature (Tm), mass loss (△m) and activation energy (E), which shows that the decomposition peak temperature and activation energy decreased obviously. Therefore, the thermal safety under humidity atmosphere become lower.

Studies on Thermal Stability and Rheological Property of PU/PVDF Blend

2011 ◽  
Vol 311-313 ◽  
pp. 1065-1070
Author(s):  
Guo Lan Huan ◽  
Jian Li Liu ◽  
Qi Yun Du ◽  
Xiao Yu Hu
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Shear Stress ◽  
Rheological Property ◽  
Decomposition Temperature ◽  
Dynamic Equations ◽  
Thermal Decomposition Temperature ◽  
Thermal Stability Of ◽  
Decomposition Activation Energy

In this article, the thermal stability of PU/PVDF blend was investigated by thermogravimetry (TG), and their rheological property was studied through testing and analyzing the rheological curves. The results showed that, with the increase in PVDF content, the thermal decomposition temperature of PU/PVDF blend increased, and by fitting relevant data to thermal decomposition dynamic equations, it was found that thermal decomposition activation energy of the blend increased gradually, i.e. the thermal stability of the blend increased gradually. Meantime, based on the curves of shear stress vs. shear rate of the blend at 180°C and 200°C, it was shown that for PU/PVDF blend, with the decrease of temperature and the increase in PVDF content, the non-Newtonian index decreased, while the viscosity of the blend increased.

scholarly journals Thermal and kinetic analysis of pure and contaminated ionic liquid: 1-butyl-2.3-dimethylimidazolium chloride (BDMIMCl)

2016 ◽  
Vol 18 (2) ◽  
pp. 122-125 ◽  
Author(s):  
Ayyaz Muhammad
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Ionic Liquid ◽  
Thermal Degradation ◽  
Kinetic Analysis ◽  
Kinetic Parameters ◽  
Process Design ◽  
Research Work ◽  
Thermal Stability Of

Abstract In this research work, thermal decomposition and kinetic analysis of pure and contaminated imidazolium based ionic liquid (IL) has been investigated. As thermal decomposition and kinetics evaluation plays a pivotal role in effective process design. Therefore, thermal stability of pure 1-butyl-2,3-dimethylimidazolium chloride (BDMIMCl) was found to be higher than the sample of IL with the addition of 20% (wt.) NH4Cl as an impurity. The activation energy of thermal degradation of IL and other kinetic parameters were determined using Coats Redfern method. The activation energy for pure IL was reduced in the presence of NH4Cl as contaminant i.e., from 58.7 kJ/mol to 46.4 kJ/mol.

Synthesis of Lanthanum Orotate and its Application as PVC Thermal Stabilizer

2021 ◽  
Vol 1032 ◽  
pp. 57-63
Author(s):  
Mansurjon Juraev ◽  
Xiao Ya Zhou ◽  
Xiao Tao Ma ◽  
Cheng Fang ◽  
Ye Qian Ge ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Synergetic Effect ◽  
Decomposition Kinetics ◽  
Stabilization Mechanism ◽  
Thermal Stability Of

The structure of basic lanthanum orotate (LaOr) were characterized by elemental analysis and infrared spectroscopy. The thermal stability of polyvinyl chloride (PVC) was further studied by Congo red method, oven discoloration method and thermogravimetric analysis. The results showed that LaOr could prolong the oven discoloration time of PVC, and the color was not completely blackened until 120 min. It has a good synergetic effect with dibenzoyl methane (DBM), and the best effect is achieved when LaOr/DBM ratio is 1.8/1.2. The thermal decomposition kinetics experiment showed that adding DBM can effectively improve the activation energy of PVC/LaOr. The stabilization mechanism of PVC was studied by absorbing HCl method and infrared spectroscopy. The results showed that LaOr could not only replace the unstable chlorine atoms on PVC, but also promote the long-term thermal stability of PVC by absorbing HCl.

The Kinetic Analysis of Thermal Decomposition of PMMA/MMT Nanocomposites

2007 ◽  
Vol 353-358 ◽  
pp. 1366-1369 ◽  
Author(s):  
Kui Chen ◽  
Rui Chen Yang ◽  
S.W. Cheng
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Methyl Methacrylate ◽  
Mass Loss ◽  
Apparent Activation Energy ◽  
Kinetic Analysis ◽  
Decomposition Kinetics ◽  
Ozawa Equation ◽  
Thermal Stability Of

The thermal decomposition kinetics and thermal stability of poly (methyl methacrylate) (PMMA) and PMMA/ montmorillonite (MMT) nanocomposites containing 4 wt% MMT were researched by thermogravimetry (TG). The results show that, because of the barrier behavior of exfoliated MMT layer, the temperature of thermal decomposition of PMMA/ MMT nanocomposites is improved by about 10 °C, and thermal stability is improved by about double. The apparent activation energy of decomposition, calculated by Ozawa equation, of nanocomposites is higher than that of PMMA before 27 % mass loss.

Non-Isothermal Decomposition Kinetic of Polypropylene/Hydrotalcite Composite

2019 ◽  
Vol 19 (11) ◽  
pp. 7493-7501 ◽  
Author(s):  
Sheng Xu ◽  
Min Zhang ◽  
Siyu Li ◽  
Moyu Yi ◽  
Shigen Shen ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Nitrogen Atmosphere ◽  
Heating Rates ◽  
Decomposition Reactions ◽  
Kinetic And Thermodynamic Parameters ◽  
Málek Method ◽  
Boundary Reaction ◽  
Phase Boundary Reaction ◽  
Thermal Stability Of

P3O5-10 pillared Mg/Al hydrotalcite (HTs) as a functional fire-retarding filler was successfully prepared by impregnation-reconstruction, where the HTs was used to prepare polypropylene (PP) and HTs composite (PP/HTs). Thermal decomposition was crucial for correctly identifying the thermal behavior for the PP/HTs, and studied using thermogravimetry (TG) at different heating rates. Based on single TG curves and Málek method, as well as 41 mechanism functions, the thermal decompositions of the PP/HTs composite and PP in nitrogen atmosphere were studied under non-isothermal conditions. The mechanism functions of the thermal decomposition reactions for the PP/HTs composite and PP were separately “chemical reaction F3” and “phase boundary reaction R2,” which were also in good agreement with corresponding experimental data. It was found that the addition of the HTs increased the apparent activation energy Ea of the PP/HTs comparing to the PP, which improved the thermal stability of the polypropylene. A difference in the set of kinetic and thermodynamic parameters was also observed between the PP/HTs and PP, particularly with respect to lower ΔS≠ value assigned to higher thermal stability of the PP/HTs composite.

Meyer-Neldel Rule on thermal stability parameters (trap depth and frequency factor) of luminescence signals in quartz

2021 ◽  
Author(s):  
Zuzanna Kabacińska ◽  
Alida Timar-Gabor ◽  
Benny Guralnik
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Hydrogen Diffusion ◽  
Dose Range ◽  
Accurate Determination ◽  
Frequency Factor ◽  
Proton Conduction ◽  
High Dose ◽  
Compensation Law ◽  
Thermal Stability Of

<p>Thermally activated processes can be described mathematically by the Arrhenius equation. The Meyer-Neldel Rule (MNR), or compensation law, linearly relates the pre-exponent term to the logarithm of the excitation enthalpy for processes that are thermally driven in an Arrhenian manner. This empirical rule was observed in many areas of materials science, in physics, chemistry, and biology. In geosciences it was found to uphold in hydrogen diffusion (Jones 2014a) and proton conduction (Jones 2014b) in minerals.</p><p>Trapped charge dating methods that use electron spin resonance (ESR) or optically or thermally stimulated luminescence (OSL and TL) are based on the dose-dependent accumulation of defects in minerals such as quartz and feldspar. The thermal stability of these defects in the age range investigated is a major prerequisite for accurate dating, while the accurate determination of the values of the trap depths and frequency factors play a major role in thermochronometry applications. </p><p>The correlation of kinetic parameters for diffusion has been very recently established for irradiated oxides (Kotomin et al. 2018). A correlation between the activation energy and the frequency factor that satisfied the Meyer–Neldel rule was reported when the thermal stability of [AlO<sub>4</sub>/h<sup>+</sup>]<sup>0</sup> and [TiO<sub>4</sub>/M<sup>+</sup>]<sup>0</sup> ESR signals in quartz was studied as function of dose (Benzid and Timar-Gabor 2020). Here we compiled the optically stimulated luminescence (OSL) data published so far in this regard, and investigated experimentally the thermal stability of OSL signals for doses ranging from 10 to 10000 Gy in sedimentary quartz samples. We report a linear relationship between the natural logarithm of the preexponent term (the frequency factor) and the activation energy E, corresponding to a Meyer-Neldel energy of 45 meV, and a deviation from first order kinetics in the high dose range accompanied by an apparent decrease in thermal stability. The implications of these observations and the atomic and physical mechanisms are currently studied.</p><p> </p><p><strong>References</strong></p><p>Benzid, K., Timar Gabor, A. 2020. The compensation effect (Meyer–Neldel rule) on [AlO<sub>4</sub>/h<sup>+</sup>]<sup>0</sup> and [TiO<sub>4</sub>/M<sup>+</sup>]<sup>0</sup> paramagnetic centers in irradiated sedimentary quartz. <em>AIP Advance</em>s 10, 075114.</p><p>Kotomin, E., Kuzovkov, V., Popov, A. I., Maier, J., and Vila, R. 2018. Anomalous kinetics of diffusion-controlled defect annealing in irradiated ionic solids. <em>J. Phys. Chem. A</em> 122(1), 28–32</p><p>Jones, A. G. (2014a), Compensation of the Meyer-Neldel Compensation Law for H diffusion in minerals, <em>Geochem. Geophys. Geosyst.</em>, 15, 2616–2631</p><p>Jones, A. G. (2014b), Reconciling different equations for proton conduction using the Meyer-Neldel compensation rule, <em>Geochem. Geophys. Geosyst</em>., 15, 337–349</p>

scholarly journals STUDY OF THERMAL DECOMPOSITION PRODUCTS OF NITROGEN-PHOSPHORUS-POTASSIUM FERTILIZERS BASED ON AMMONIUM NITRATE BY X-RAY DIFFRACTUON

2017 ◽  
Vol 61 (1) ◽  
pp. 72
Author(s):  
Konstantin G. Gorbovskiy ◽  
Alena S. Ryzhova ◽  
Andrey M. Norov ◽  
Denis A. Pagaleshkin ◽  
Valentina N. Kalinina ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Phosphoric Acid ◽  
Ammonium Nitrate ◽  
Confined Space ◽  
Decomposition Products ◽  
X Ray ◽  
Thermal Decomposition Products ◽  
Nitrogen Phosphorus ◽  
Thermal Stability Of

Complex mineral ammonium nitrate-based fertilizers are complex multicomponent salt systems possessing low thermal stability and prone to self-sustaining decomposition. This leads to the need to increase the requirements for fire and explosion safety in their manufacture, storage and transportation, caused by the fact that ammonium nitrate is a solid oxidant able to support a combustion, and its heating in confined space can lead to detonation. Components that make up such fertilizers can both reduce (phosphates and ammonium sulfate) and accelerate (chlorine compounds) decomposition of ammonium nitrate. Thus, the thermal stability of fertilizers based on ammonium nitrate largely depends on the ratio of the components that make up its composition or formed as a result of the chemical reaction. The simplest way to reduce the content of ammonium nitrate and increase the thermal stability of fertilizer without changing the content of essential nutrients is to increase the degree of phosphoric acid ammoniation. In this paper, the phase composition change of grade 22:11:11 nitrogen-phosphorus-potassium fertilizer obtained with different ammoniation degree in the process of thermal decomposition was studied by X-ray phase analysis. To obtain this fertilizer, wet-process phosphoric acid obtained sulfuric acid attack of the Khibin apatite concentrate by a hemihydrate method is used. It is shown that an increase in the ammoniation degree has a significant effect on the exothermic decomposition of ammonium nitrate and the amount of material that is released into the gas phase. The phases formed at each stage of the decomposition are determined.Forcitation:Gorbovskiy K.G., Ryzhova A.S., Norov A.M., Pagaleshkin D.A., Kalinina V.N., Mikhaylichenko A.I. Study of thermal decomposition products of nitrogen-phosphorus-potassium fertilizers based on ammonium nitrate by X-ray diffractuon. Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol. 2018. V. 61. N 1. P. 72-77

scholarly journals Thermal stability and thermal decomposition of sucralose

2018 ◽  
Vol 39 (4) ◽  
pp. 21
Author(s):  
Gilbert Bannach ◽  
Rafael R. Almeida ◽  
Luis G. Lacerda ◽  
Egon Schnitzler ◽  
Massao Ionashiro
Keyword(s):  
Thermal Stability ◽  
Thermal Analysis ◽  
Differential Scanning Calorimetry ◽  
Thermal Decomposition ◽  
Differential Thermal Analysis ◽  
Infrared Spectroscopy ◽  
Scanning Calorimetry ◽  
Thermoanalytical Techniques ◽  
Thermal Stability Of

Several papers have been described on the thermal stability of the sweetener, C12H19Cl3O8 (Sucralose). Nevertheless no study using thermoanalytical techniques was found in the literature. Simultaneous thermogravimetry and differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC) and infrared spectroscopy, have been used to study the thermal stability and thermal decomposition of sweetener.

Thermal Stability of Ultrafine-Grained Pure Titanium Processed by High-Pressure Torsion

2021 ◽  
Vol 1016 ◽  
pp. 338-344
Author(s):  
Wan Ji Chen ◽  
Jie Xu ◽  
De Tong Liu ◽  
De Bin Shan ◽  
Bin Guo ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Grain Size ◽  
High Pressure ◽  
Annealing Temperature ◽  
High Pressure Torsion ◽  
Stored Energy ◽  
Ultrafine Grained ◽  
Average Grain Size ◽  
Thermal Stability Of

High-pressure torsion (HPT) was conducted under 6.0 GPa on commercial purity titanium up to 10 turns. An ultrafine-grained (UFG) pure Ti with an average grain size of ~96 nm was obtained. The thermal properties of these samples were studied by using differential scanning calorimeter (DSC) which allowed the quantitative determination of the evolution of stored energy, the recrystallization temperatures, the activation energy involved in the recrystallization of the material and the evolution of the recrystallized fraction with temperature. The results show that the stored energy increases, beyond which the stored energy seems to level off to a saturated value with increase of HPT up to 5 turns. An average activation energy of about 101 kJ/mol for the recrystallization of 5 turns samples was determined. Also, the thermal stability of the grains of the 5 turns samples with subsequent heat treatments were investigated by microstructural analysis and Vickers microhardness measurements. It is shown that the average grain size remains below 246 nm when the annealing temperature is below 500 °C, and the size of the grains increases significantly for samples at the annealing temperature of 600 °C.

scholarly journals Study on Thermal Decomposition Behaviors of Terpolymers of Carbon Dioxide, Propylene Oxide, and Cyclohexene Oxide

2018 ◽  
Vol 19 (12) ◽  
pp. 3723 ◽  
Author(s):  
Shaoyun Chen ◽  
Min Xiao ◽  
Luyi Sun ◽  
Yuezhong Meng
Keyword(s):  
Carbon Dioxide ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Thermogravimetric Analysis ◽  
Propylene Carbonate ◽  
Cyclohexene Oxide ◽  
Block Polymers ◽  
Rate Method ◽  
Poly Propylene ◽  
Thermal Stability Of

The terpolymerization of carbon dioxide (CO2), propylene oxide (PO), and cyclohexene oxide (CHO) were performed by both random polymerization and block polymerization to synthesize the random poly (propylene cyclohexene carbonate) (PPCHC), di-block polymers of poly (propylene carbonate–cyclohexyl carbonate) (PPC-PCHC), and tri-block polymers of poly (cyclohexyl carbonate–propylene carbonate–cyclohexyl carbonate) (PCHC-PPC-PCHC). The kinetics of the thermal degradation of the terpolymers was investigated by the multiple heating rate method (Kissinger-Akahira-Sunose (KAS) method), the single heating rate method (Coats-Redfern method), and the Isoconversional kinetic analysis method proposed by Vyazovkin with the data from thermogravimetric analysis under dynamic conditions. The values of ln k vs. T−1 for the thermal decomposition of four polymers demonstrate the thermal stability of PPC and PPC-PCHC are poorer than PPCHC and PCHC-PPC-PCHC. In addition, for PPCHC and PCHC-PPC-PCHC, there is an intersection between the two rate constant lines, which means that, for thermal stability of PPCHC, it is more stable than PCHC-PPC-PCHC at the temperature less than 309 °C and less stable when the decomposed temperature is more than 309 °C. Pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) and thermogravimetric analysis/infrared spectrometry (TG/FTIR) techniques were applied to investigate the thermal degradation behavior of the polymers. The results showed that unzipping was the main degradation mechanism of all polymers so the final pyrolysates were cyclic propylene carbonate and cyclic cyclohexene carbonate. For the block copolymers, the main chain scission reaction first occurs at PC-PC linkages initiating an unzipping reaction of PPC chain and then, at CHC–CHC linkages, initiating an unzipping reaction of the PCHC chain. That is why the T−5% of di-block and tri-block polymers were not much higher than that of PPC while two maximum decomposition temperatures were observed for both the block copolymer and the second one were much higher than that of PPC. For PPCHC, the random arranged bulky cyclohexane groups in the polymer chain can effectively suppress the backbiting process and retard the unzipping reaction. Thus, it exhibited much higher T−5% than that of PPC and block copolymers.

Sign in / Sign up

Export Citation Format

Share Document