Mechanical Properties of Epoxy Clay Nanocomposites

2010 ◽  
Vol 123-125 ◽  
pp. 145-148 ◽  
Author(s):  
Sahar Ghafarloo ◽  
Mehrdad Kokabi
Keyword(s):  
Mechanical Properties ◽  
Diglycidyl Ether ◽  
Good Evidence ◽  
Layered Silicates ◽  
Clay Nanocomposites ◽  
Curing Agent ◽  
Test Results ◽  
X Ray Diffraction ◽  
Cloisite 30B ◽  
Diffraction Patterns

Achievement of exfoliated structure of polymer/ Clay nanocomposites is of particular interest for the improvement of mechanical properties. In this work, the morphology and mechanical properties of epoxy/ clay nanocomposites has been investigated. Diglycidyl ether of bis-phenol A (DGEBA) epoxy resin (EPON828) and Jeffamine D400 curing agent was used. To obtain perfect dispersion, nanoclay (Cloisite 30B) was sonicated in acetone. The mixture was then mixed with polymer. Afterwards, the curing process was performed by addition of curing agent and degassing. Disappearing of peaks in X-Ray diffraction patterns of nanocomposites containing less than 5wt% nanoclay, is a good evidence of perfect dispersion of layered silicates in matrix, i.e. formation of exfoliated morphology. Based on tensile test results, it is deduced that as the amount of nanoclay increases, the elastic modulus and elongation at break of the nanocomposites containing 1wt% and 5wt% nanoclay increases by 12% and 31%, respectively. Therefore, obtaining perfect dispersion of layered silicates in epoxy matrix and exfoliated morphology, results in better mechanical properties of the nanocomposites.

Preparation of Exfoliated Polyethylene/Clay Nanocomposites at High Clay Content

2010 ◽  
Vol 150-151 ◽  
pp. 561-564
Author(s):  
Hao Qun Hong ◽  
Hai Yan Zhang ◽  
Hui He ◽  
De Min Jia
Keyword(s):  
Solid Phase ◽  
Clay Content ◽  
Layered Silicates ◽  
Clay Nanocomposites ◽  
Melt Blending ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Diffraction Patterns ◽  
High Polarity

The polyethylene/montmorillonite (PE/MMT) nanocomposites were prepared by melt blending the organic MMT with the ternary-monomer graft copolymers of polyethylene (GPE) which were prepared by solid phase grafting maleic anhydride, methyl methacrylate and butyl acrylate onto PE. Fourier transform infrared spectroscopy was used to characterize the structure of GPE. X-ray diffraction patterns and transmission electron microscopy were used to characterize the morphology of GPE/MMT nanocomposites. Results showed that GPE was an outstanding polymeric material to prepare an exfoliated polymer/layered silicates nanocomposites due to the high polarity of GPE and high graft degree. Most layered silicates still maintain the exfoliated and well dispersed state even at 40 phr OMMT content. The exfoliation of layered silicates was attributed to the well intercalation and easy wetting of the grafted oligomers.

Influence of Epoxide Levels in Epoxidized Natural Rubber (ENR) Molecules on Cure Characteristics, Dynamic Properties and Mechanical Properties of ENR/Montmorillonite Clay Nanocomposites

2013 ◽  
Vol 844 ◽  
pp. 247-250
Author(s):  
Piriyapol Yokkhun ◽  
Bencha Thongnuanchan ◽  
Charoen Nakason
Keyword(s):  
Mechanical Properties ◽  
Dynamic Properties ◽  
Montmorillonite Clay ◽  
Layered Silicates ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Melt Mixing ◽  
Maximum Torque ◽  
Elongation At Break ◽  
Cure Characteristics

Nanocomposites based on epoxidized natural rubbers (ENRs) with various levels of epoxide groups (i.e., 10, 20, 30, 40 and 50 mol%) and organoclay were prepared by melt mixing process. The organoclay employed in this study was montmorillonite clay modified by octadecylamine (OC-MMT). Cure characteristics, dynamic properties and mechanical properties of ENRs nanocomposites filled with 5 phr of OC-MMT were studied. In all cases, X-ray diffraction results indicated intercalation of ENRs into the silicate interlayer as an increase in the interlayer distance of layered silicates was observed. The maximum torque and torque difference of ENRs nanocomposites increased with increasing levels of epoxide groups in ENRs. Additionally, it was also found that the tan δ value at Tg of the ENR-50 nanocomposite was much lower than those of other types of ENRs nanocomposite. This indicates stronger interaction between ENR-50 and OC-MMT. However, ENR-50 nanocomposite showed the poorest elasticity in term of the tan δ value at the ambient temperature compared to other types of ENRs nanocomposites. A good balance between strength and elasticity was also observed in the ENR-30 nanocomposite. These results are also consistent with the observation that tensile strength and elongation at break of ENR-30 nanocomposite were higher than those of other types of ENRs nanocomposites.

Epoxy-Layered Silicate and Epoxy MWCNTs Nanocomposites

2011 ◽  
Vol 146 ◽  
pp. 160-169 ◽  
Author(s):  
A. Stan ◽  
I. Dinca ◽  
C. Ban ◽  
S. Ilina ◽  
Dan Donescu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Epoxy Polymer ◽  
Layered Silicate ◽  
Diglycidyl Ether ◽  
Curing Agent ◽  
Fluid Behavior ◽  
Cloisite 30B ◽  
Organically Modified

The paper deals with the rheological properties of epoxy resin additivated with organically modified montmorillonites, carbon nanotubes and nanocarbon. The paper also presents the influence of nanoadditives over composites mechanical properties. The epoxy polymer is diglycidyl ether of bisphenol A (DGEBA) and the curing agent is an aliphatic tetraamine. Organically modified montmorillonites Cloisite 30B and Cloisite 93A, MWCNTs and laser synthesized nanocarbon were used to synthesize nanocomposites by dispersing each in an epoxy resin. The dispersion was achieved through mechanical and sonic methods. The epoxy resin additivated with nanosized fillers was rheologically tested to study the dispersion influence. The sonic dispersion of nanoadditives is observed to drastically influence the rheological behavior of the suspensions. Newtonian fluid behavior disappears as the additive loading increases. The work mentions the influence of nanoadditives on the manufacturing process of epoxy /glass fibre and epoxy/ carbon fibre laminated composites.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Structure and properties of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/poly(L-lactic acid) quasi core/sheath melt-electrospun microfibers

2018 ◽  
Vol 89 (9) ◽  
pp. 1770-1781 ◽  
Author(s):  
Huaizhong Xu ◽  
Benedict Bauer ◽  
Masaki Yamamoto ◽  
Hideki Yamane
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffraction Patterns

A facile route was proposed to fabricate core–sheath microfibers, and the relationships among processing parameters, crystalline structures and the mechanical properties were investigated. The compression molded poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH)/poly(L-lactic acid) (PLLA) strip enhanced the spinnability of PHBH and the mechanical properties of PLLA as well. The core–sheath ratio of the fibers was determined by the prefab strip, while the PLLA sheath component did not completely cover the PHBH core component due to the weak interfacial tension between the melts of PHBH and PLLA. A rotational target was applied to collect aligned fibers, which were further drawn in a water bath. The tensile strength and the modulus of as-spun and drawn fibers increased with increasing the take-up velocities. When the take-up velocity was above 500 m/min, the jet became unstable and started to break up at the tip of the Taylor cone, decreasing the mechanical properties of the fibers. The drawing process facilitated the crystallization of PLLA and PHBH, and the tensile strength and the modulus increased linearly with the increasing the draw ratio. The crystal information displayed from wide-angle X-ray diffraction patterns and differential scanning calorimetry heating curves supported the results of the tensile tests.

Effect of High Shear Mixing Parameters and Degassing Temperature on the Morphology of Epoxy-Clay Nanocomposites

2013 ◽  
Vol 652-654 ◽  
pp. 159-166 ◽  
Author(s):  
Muneer Al-Qadhi ◽  
Nesar Merah ◽  
Khaled Mezghani ◽  
Zafarullah Khan ◽  
Zuhair Gasem ◽  
...  
Keyword(s):  
Mixing Time ◽  
Diglycidyl Ether ◽  
Clay Nanocomposites ◽  
High Shear ◽  
X Ray Diffraction ◽  
Transmission Microscopy ◽  
Clay Dispersion ◽  
Mixing Speed ◽  
Shear Mixing ◽  
Mixing Method

Epoxy-clay nanocomposites were prepared by high shear mixing method using Nanomer I.30E nanoclay as nano-reinforcement in diglycidyl ether of bisphenol A (DGEBA). The effect of mixing speed and time on the nature and degree of clay dispersion were investigated by varying the mixing speed in the range of 500-8000 RPM and mixing time in the range of 15-90 minutes. The effect of degassing temperature on the morphology of the resultant nanocomposites was also studied. Scanning and transmission microscopy (SEM & TEM) along with x-ray diffraction (XRD) have been used to characterize the effect of shear mixing speed, mixing time and degassing temperature on the structure of the resultant nanocomposites. The SEM, TEM and XRD examinations demonstrated that the degree of clay dispersion was improved with increasing the high shear mixing speed and mixing time. The results showed that the optimum high shear mixing speed and mixing time were 6000 rpm and 60 min, respectively. It was observed that the structure of the nanocomposites that have been degassed at 65oC was dominated by ordered intercalated morphology while disordered intercalated with some exfoliated morphology was found for the sample degassed at 100oC for the first 2 hours of the degassing process.

Curing study and evaluation of epoxy resin with amine functional chloroaniline acetaldehyde condensate

2015 ◽  
Vol 44 (1) ◽  
pp. 19-25
Author(s):  
T. Maity ◽  
B.C. Samanta
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Epoxy Resin ◽  
Ph Value ◽  
Kinetic Studies ◽  
Diglycidyl Ether ◽  
Curing Agent ◽  
Scanning Calorimetry ◽  
Content Type ◽  
Curing Reaction

Purpose – The purpose of this paper was to check effectiveness of amine functional chloroaniline acetaldehyde condensate (AFCAC) as a new curing agent for diglycidyl ether of bisphenol A (DGEBA) resin. For this purpose, first AFCAC was synthesised, characterised and then curing reaction was carried out. Design/methodology/approach – Equimolecular mixture of AFCAC and DGEBA was subjected to curing reaction, and the reaction was followed by differential scanning calorimetry (DSC) analysis. The kinetic studies of this curing reaction were also carried out from those DSC exotherms. The mechanical properties, dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) of cured epoxy were also reported. Findings – DSC results reflected the effective first order curing reaction of AFCAC with epoxy resin. Mechanical properties reflected appreciable rigidity of AFCAC cured epoxy matrix and TGA showed that the cured epoxy networks were thermally stable up to around 297°C. Research limitations/implications – The curing agent AFCAC was synthesised by using chloroaniline and acetaldehyde in acid medium. There are some limitations for this procedure. The synthetic procedure is pH dependent. So reaction cannot be done at any pH value. The reaction must also be carried out at room temperature without any heating. To obtain low molecular weight curing agent, chloroaniline and acetaldehyde cannot be taken in equimolecular ratio because the equimolecular mixture of them produces high molecular weight condensate. This was shown in our previous publication. Some implications are also there. By changing amine and aldehyde other curing agents could be synthesised and the curing efficiency of those for epoxy resin could also be studied. Originality/value – Experimental results revealed the greater suitability of AFCAC as curing agent for DGEBA resin and novelty of AFCAC cured matrix in the field of protective coating, casting, adhesives, etc.

scholarly journals Isotropic microscale mechanical properties of coral skeletons

2015 ◽  
Vol 12 (106) ◽  
pp. 20150168 ◽  
Author(s):  
Luca Pasquini ◽  
Alan Molinari ◽  
Paola Fantazzini ◽  
Yannicke Dauphen ◽  
Jean-Pierre Cuif ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Nacreous Layer ◽  
X Ray Diffraction ◽  
Stylophora Pistillata ◽  
Force Microscopy ◽  
Coral Skeletons ◽  
Atomic Force ◽  
Diffraction Patterns ◽  
The Relationship ◽  
Atrina Rigida

Scleractinian corals are a major source of biogenic calcium carbonate, yet the relationship between their skeletal microstructure and mechanical properties has been scarcely studied. In this work, the skeletons of two coral species: solitary Balanophyllia europaea and colonial Stylophora pistillata , were investigated by nanoindentation. The hardness H IT and Young's modulus E IT were determined from the analysis of several load–depth data on two perpendicular sections of the skeletons: longitudinal (parallel to the main growth axis) and transverse. Within the experimental and statistical uncertainty, the average values of the mechanical parameters are independent on the section's orientation. The hydration state of the skeletons did not affect the mechanical properties. The measured values, E IT in the 76–77 GPa range, and H IT in the 4.9–5.1 GPa range, are close to the ones expected for polycrystalline pure aragonite. Notably, a small difference in H IT is observed between the species. Different from corals, single-crystal aragonite and the nacreous layer of the seashell Atrina rigida exhibit clearly orientation-dependent mechanical properties. The homogeneous and isotropic mechanical behaviour of the coral skeletons at the microscale is correlated with the microstructure, observed by electron microscopy and atomic force microscopy, and with the X-ray diffraction patterns of the longitudinal and transverse sections.

Biodegradable Nanocomposites of Poly(hydroxybutyrate-co-hydroxyvalerate): The Effect of Nanoparticles

2008 ◽  
Vol 8 (4) ◽  
pp. 1858-1866 ◽  
Author(s):  
Pralay Maiti ◽  
Jaya P. Prakash Yadav
Keyword(s):  
Mechanical Properties ◽  
Layered Silicate ◽  
Layered Silicates ◽  
Thermal And Mechanical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Silicate Nanocomposites ◽  
Transmission Electron ◽  
Superior Mechanical Properties ◽  
Biodegradable Nanocomposites

Copolymer of hydroxybutyrate and hydroxyvalerate, P(HB-HV)/layered silicate or hydroxyapatite nanocomposites were prepared via melt extrusion. The nanostructure, as observed from wide-angle X-ray diffraction and transmission electron microscopy, indicate intercalated hybrids for layered silicates. Hydroxyapatite of nanometer dimension is uniformly distributed in matrix copolymer. The nanohybrids show significant improvement in thermal and mechanical properties of the copolymer as compared to the neat copolymer. The layered silicate nanocomposites exhibit superior mechanical properties as compared to hydroxyapatite nanohybrid. The thermal expansion coefficient is significantly reduced in nanohybrids. The biodegradability of pure copolymer and its nanocomposites were studied at room temperatures under controlled conditions in compost media. The rate of biodegradation of copolymer is enhanced dramatically in the nanohybrids. Hydroxyapatite hybrid shows highest rate of biodegradation. The change in biodegradation is streamlined in terms of nature of nanoparticles used to prepare hybrids.

The Effects of Bagasse Fiber Loading on the Mechanical Properties of Skim NR–Clay Nanocomposites

2016 ◽  
Vol 835 ◽  
pp. 42-49
Author(s):  
Tarinee Nampitch ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Fatigue Testing ◽  
Fiber Content ◽  
Clay Nanocomposites ◽  
Fiber Loading ◽  
Cloisite 30B ◽  
Cure Time ◽  
Renewable Material ◽  
Bagasse Fiber ◽  
Cloisite 20A

Skim natural rubber (NR)–clay nanocomposites were prepared by a coagulation method using the organoclays Cloisite 15A, Cloisite 20A and Cloisite 30B. This work investigated the use of bagasse fiber developed from locally sourced and renewable material as an alternative and/or secondary filler in skim NR–clay nanocomposites. Bagasse fiber loading in the nanocomposites was 0, 5, 10 and 20 phr; the effects of fiber content on cure characteristics and mechanical properties were then determined. The results suggest that the Mooney viscosity tended to increase with increasing fiber content, whereas the cure time at 90% and fatigue testing score decreased as fiber loading increased.

Sign in / Sign up

Export Citation Format

Share Document