Synthesis and Characterization of Li-Ti-O Nano-Composites and Their Doped BaTiO3 Based X7R-Type Ceramics

2010 ◽  
Vol 148-149 ◽  
pp. 1575-1579
Author(s):  
Qing Zhang ◽  
Rui Yuan Niu ◽  
Min Wang ◽  
Bin Cui ◽  
Zhu Guo Chang
Keyword(s):  
Particle Size ◽  
Dielectric Properties ◽  
Ph Value ◽  
Sol Gel ◽  
Nano Composites ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Minimum Particle Size ◽  
Sol Gel Process

Li-Ti-O (abbreviated as LTO) nano-composites were synthesized via sol-gel process, and then doped BaTiO3 based X7R type ceramics. The LTO nano-composites and their ceramics were characterized by means of thermaogravimetric, Fourier-transform infrared, X-ray diffraction methods, transmission electron microscopy. We also characterized the dielectric properties of the LTO doped BaTiO3 based ceramics of X7R type. The results indicated that LTO nano-composites were nanometer scale powders. The pH value and calcining temperature had an influence on particle size of LTO sintering aids. At pH about 3 and with calcining at 600 °C, the nano-composites attained minimum particle size (about 10 nm). By adding 0.10 wt% of the LTO nano-composites, the temperature permittivity achieved about 4200 when sintered at 1240 °C for 4 h, and the dielectric properties met X7R standard.

Sol-gel derived Ba(Mg1/3Ta2/3)O3 thin films: Preparation and structure

1997 ◽  
Vol 12 (3) ◽  
pp. 596-599 ◽  
Author(s):  
Ji Zhou ◽  
Qing-Xin Su ◽  
K. M. Moulding ◽  
D. J. Barber
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Small Grains

Ba(Mg1/3Ta2/3)O3 thin films were prepared by a sol-gel process involving the reaction of barium isopropoxide, tantalum ethoxide, and magnesium acetate in 2-methoxyethanol and subsequently hydrolysis, spin-coating, and heat treatment. Transmission electron microscopy, x-ray diffraction, and Raman spectroscopy were used for the characterization of the thin films. It was shown that the thin films tend to crystallize with small grains sized below 100 nm. Crystalline phase with cubic (disordered) perovskite structure was formed in the samples annealed at a very low temperature (below 500 °C), and well-crystallized thin films were obtained at 700 °C. Although disordered perovskite is dominant in the thin films annealed below 1000 °C, a low volume fraction of 1 : 2 ordering domains was found in the samples and grows with an increase of annealing temperature.

scholarly journals Preparation and Characterization of Nano-Cadmium Ferrite

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
S. M. Ismail ◽  
Sh. Labib ◽  
S. S. Attallah
Keyword(s):  
Particle Size ◽  
Low Temperature ◽  
Sol Gel ◽  
Stable Phase ◽  
X Ray Diffraction ◽  
Economic Point ◽  
Sol Gel Process ◽  
Pure Phase ◽  
Microstructural Studies

Nano-hematite (α-Fe2O3) and nano-cadmium ferrite (CdFe2O4) are prepared using template-assisted sol-gel method. The prepared samples are analyzed using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and Mössbauer spectroscopy techniques for structural and microstructural studies. Nano-α-Fe2O3 with particle size ~60 nm is formed at 500°C, while nano-CdFe2O4 with smaller particle size (~40 nm) is formed at 600°C. It is found that with a simple sol-gel process we can prepare nano-CdFe2O4 with better conditions than other methods: pure phase at lower sintering temperature and time (economic point) and of course with a smaller particle size. So, based on the obtained experimental results, a proposed theoretical model is made to explain the link between the use of the sol-gel process and the formation of nano-CdFe2O4 as a pure phase at low temperature. This model is based on a simple magnetostatic interaction between the formed nuclei within the solution leading to the formation of the stable phase at low temperature.

Effect of TiO2 addition on the preparation of β-spodumene powders by sol-gel process

1999 ◽  
Vol 14 (1) ◽  
pp. 196-203 ◽  
Author(s):  
Moo-Chin Wang ◽  
Ming-Hong Lin ◽  
Hok-Shing Liu
Keyword(s):  
Electron Microscopy ◽  
Ph Value ◽  
Sol Gel ◽  
Gelation Time ◽  
Glass Ceramics ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Fine Glass ◽  
A Minor

This study has shown the possibility of achieving two primary considerations for the advanced fabrication of spodumene with a composition of Li2O · Al2O3 · 4SiO2 · nTiO2 (LAST) glass-ceramics by a sol-gel process, namely, an enormous reduction of sintering temperature from 1600 to 1200 °C together with the appearance of simple phases of β-spodumene/rutile as opposed to products via the conventional melting-crystallization process. Fine glass-ceramic powders with a composition of Li2O · Al2O3 · 4SiO2 (LAS) have been synthesized by the sol-gel process using Si(OC2H5)4, Al(OC2H5)3, LiOCH3, and Ti(OC2H5)4 as the starting materials. The process included well-controlled hydrolysis polycondensation of the raw alkoxides. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron diffraction (ED) analysis were utilized to study the effect of TiO2 addition on the preparation of β-spodumene powders by the sol-gel process. The gelation time of the LAST solution increases as the TiO2 content increases. For the low (<3) or high (>11) pH value, the gelation time was shortened. At pH = 5, regardless of the TiO2 content, the gel has the longest time of gelation. When the dried gels of the LAST system are heated from 800 to 1200 °C, the crystallized samples are composed of the major phase of β-spodumene and a minor phase of rutile (TiO2).

EVALUATION OF HYDROXYAPATITE-FORSTERITE-BIOACTIVE GLASS COMPOSITE NANOPOWDER PREPARED VIA SOL-GEL METHOD

2012 ◽  
Vol 05 ◽  
pp. 510-518
Author(s):  
MARYAM MAZROOEI SEBDANI ◽  
MOHAMMADHOSSEIN FATHI
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Bioactive Glass ◽  
Sintering Temperature ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Bioactive Ceramics ◽  
Transmission Electron ◽  
Alternative Approach ◽  
Sol Gel Process

In spite of attractive bioactivity of bioactive ceramics i.e. hydroxyapatite and bioactive glasses, their poor mechanical properties have restricted their clinical applications. To overcome these limitations, an alternative approach suggested is preparation a composite including these bioactive ceramics with others. It is expected that a ceramic reinforcement with reduced grain size below 100 nm promotes theirs. The aim of this work was fabrication and characterization of hydroxyapatite-forsterite-bioglass composite nanopowder. Novel hydroxyapatite-forsterite-bioglass composite nanopowder was synthesized by incorporation of the forsterite and bioactive glass in hydroxyapatite matrix via a sol-gel process. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and fourier transform infrared (FTIR) spectroscopy techniques were utilized in order to evaluate the phase composition, agglomerates size distribution, morphology and particle size and functional groups of synthesized. The effects of sintering temperature and time were also investigated. Results showed that the appropriate temperature for calcination was 600°C and the particle size of composite nanopowder was about 60-70nm. The decomposition of hydroxyapatite was increased with the increase of the sintering temperature and sintering time. Obtained results indicate that prepared composite nanopowder could be a good candidate for medical applications.

Preparation and Characterization of (Ba0.88Ca0.12)(Zr0.12Ti0.88)O3 Powders and Ceramics Produced by Sol-Gel Process

2010 ◽  
Vol 148-149 ◽  
pp. 1062-1066 ◽  
Author(s):  
Ren Bo Yang ◽  
Wei Guo Fu ◽  
Xiang Yun Deng ◽  
Zhong Wen Tan ◽  
Yan Jie Zhang ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Particle Size ◽  
Piezoelectric Coefficient ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Thermo Gravimetric ◽  
X Ray ◽  
Sol Gel Process

The (Ba0.88Ca0.12)( Zr0.12Ti0.88)O3 powders and piezoelectric ceramics were prepared by sol-gel process. The reaction process was analyzed with the help of thermo gravimetric and differential scanning calorimetry. X-ray diffraction characterized results showed that the structure of the (Ba0.88Ca0.12)( Zr0.12Ti0.88)O3 powders was perovskite structure and the particle size was approximately 37nm. Piezoelectric measurements revealed that Curie temperature and the maximum piezoelectric coefficient d33 is 95°C and 215pm/V, respectively.

scholarly journals PREPARATION AND STUDY OF FERRITE GARNET R3Fe5O12 (R=Y, Gd, Dy) NANOPARTICLES

2012 ◽  
Vol 15 (2) ◽  
pp. 27-34
Author(s):  
Nguyet Thi Thuy Dao ◽  
Duong Phuc Nguyen ◽  
Hien Duc Than
Keyword(s):  
Particle Size ◽  
Sol Gel ◽  
Average Particle Size ◽  
Particle Morphology ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Ferrite Garnet ◽  
Transmission Electron ◽  
Scherrer Formula

This paper presents the synthesis and characterization of Y3Fe5O12, Gd3Fe5O12 and Dy3Fe5O12 nanoparticles by sol-gel method using initial salts solution of Y(NO3)3, Gd(NO3)3, Dy(NO3)3, Fe(NO3). The lattice constant, crystallite size and particle morphology of these ferrite garnet nanoparticles were studied by using X-ray diffraction and transmission electron microscopy (TEM). The results showed that the garnet samples prepared by this method were formed at 800oC, which is lower than the sintering temperature for ceramic bulk samples (1400oC). The particle size is in the range 25- 40 nm as observed via TEM image and the average particle size was found to be 37nm using Debye- Scherrer formula.

Dielectric Properties of Pb0.97La0.02Zr0.95Ti0.05O3 Antiferroelectric Thin Films Prepared at Different Annealing Temperatures

2011 ◽  
Vol 287-290 ◽  
pp. 2460-2463
Author(s):  
Wen Ping Geng ◽  
Xiu Jian Chou ◽  
Ya Ting Zhang ◽  
Mao Xiang Guo ◽  
Jun Liu
Keyword(s):  
Thin Films ◽  
Dielectric Properties ◽  
Electric Field ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
Dielectric Constant And Loss ◽  
Sol Gel Process ◽  
Plzt Thin Films

Pb0.97La0.02Zr0.95Ti0.05O3(PLZT) antiferroelectric thin films were prepared on Pt (111)/ Ti/SiO2/Si (100) substrates by a sol-gel process. The influences of annealing temperature on the structures and dielectric properties of the PLZT antiferroelectric thin films were investigated. And the phase structure and crystal orientation were studied by X-ray diffraction analyses (XRD). The antiferroelectric characterization of the PLZT thin films annealed at different temperature was demonstrated by P(polarization)-E(electric field) and C(capactitance)-E(electric field) curves. The maximum polarizations for the films annealed at 650°C, 700°C and 750°C were 35μC/cm2, 42μC/cm2and 47μC/cm2, respectively. The temperature dependent of the dielectric constant and loss was measured under the frequency 1, 10, 100 and 1000 kHz. The films annealed at 700°C have high (100)-preferred orientation and excellent dielectric properties.

CONTROLLED SYNTHESIS AND CHARACTERIZATION OF TiO2 NANOPARTICLES VIA A SOL–GEL METHOD

2004 ◽  
Vol 03 (06) ◽  
pp. 749-755 ◽  
Author(s):  
YING LI ◽  
SUO HON LIM ◽  
TIM WHITE
Keyword(s):  
Sol Gel ◽  
Critical Role ◽  
Rietveld Analysis ◽  
Nanocrystalline Powders ◽  
X Ray Diffraction ◽  
Gelation Temperature ◽  
Gel Method ◽  
Sol Gel Method ◽  
Transmission Electron

The properties influencing the photocatalytic activity of TiO 2 particles have been suggested to include the surface area, crystallinity, crystallite size and crystal structure. Therefore, manipulation of the microstructure of titania, especially of nanocrystalline powders, is very important in the preparative process. In this study, nanocrystalline TiO 2 powders with controlled particle size and phase composition were synthesized at low temperature (<80°C) by a modified sol–gel method. The effects of gelation temperature were systematically investigated. It was found that this parameter played a critical role in determining the crystallinity of single phase anatase. With increasing gelation temperature, the crystallinity of anatase improved initially and then decreased if the temperature was raised to 80°C. These nanomaterials were characterized comprehensively by powder X-ray diffraction (including Rietveld analysis), high-resolution transmission electron microscopy, DSC/TGA thermal analysis and UV–Vis spectrometry.

Low-Temperature Synthesis of Nano-Crystalline ZnTiO3 Powders by Aqueous Sol-Gel Process

2014 ◽  
Vol 543-547 ◽  
pp. 3741-3744
Author(s):  
Quan Jing Mei ◽  
Cong Ying Li ◽  
Jing Dong Guo ◽  
Gui Wang ◽  
Hai Tao Wu
Keyword(s):  
Sol Gel ◽  
Zinc Nitrate ◽  
X Ray Diffraction ◽  
Low Temperature Synthesis ◽  
Temperature Synthesis ◽  
Calcination Process ◽  
X Ray ◽  
Nano Crystalline ◽  
Transmission Electron ◽  
Sol Gel Process

The ecandrewsite-type ZnTiO3was successfully synthesized by the aqueous sol-gel method using TiO2dioxide and zinc nitrate as starting materials instead of expensive organic solvent and metal alkoxides. The as-prepared nanopowders were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA) and transmission electron microscopy (TEM), respectively. The results showed that the calcination process of gel consisted of a series of oxidation and combustion reactions, accompanied by significantly exothermal effects. Highly reactive nanosized ZnTiO3powders were successfully obtained at 850 °C with particle size ~50 nm. By comparison, the aqueous sol-gel process was the most effective and least expensive technique used for the preparation of ZnTiO3nanopowders.

Effect of Process on the Dielectric Properties of BaTiO3-Based X9R Ceramics

2014 ◽  
Vol 906 ◽  
pp. 18-24 ◽  
Author(s):  
Bao Lin Zhang ◽  
Bin Bin Zhang ◽  
Ning Ning Wang ◽  
Jing Ming Fei
Keyword(s):  
Particle Size ◽  
Dielectric Properties ◽  
Milling Time ◽  
Sintering Temperature ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Sintered Ceramic ◽  
X Ray ◽  
Particle Size Analyzer

The effect of milling time and sintering process on the dielectric properties of BaTiO3-based X9R ceramics was investigated. The characterization of the raw powders and the sintered ceramic was carried out by X-ray diffraction and scanning electron microscopy. The particle size distribution of the mixed powders was examined by Laser Particle Size Analyzer. The results shown that with the milling time extended, the Cruie Peak was depressed, or even disappeared. Moreover, with the rise of sintering temperature, the dielectric constant of the ceramics increased and the dielectric loss decreased gradually. Eventually, by milling for 11h and sintering at 1090°Cfor 2h, good dielectric properties were obtained, which were ε25°C≥ 2526, εr/εr25°C≤± 12% (–55~200°C), tanδ≤1.12% (25°C).

Sign in / Sign up

Export Citation Format

Share Document