Studies on the Low-Velocity Impact Response of Ultra-High Molecular Weight Polyethylene Laminated Composites

2011 ◽  
Vol 332-334 ◽  
pp. 1691-1694
Author(s):  
Dian Tang Zhang ◽  
Bao Dong Li ◽  
Ying Sun ◽  
Ning Pan
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Impact Energy ◽  
Laminated Composites ◽  
Peak Load ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Ultra High Molecular Weight

The low-velocity impact response of Ultra-High Molecular Weight Polyethylene (UHMWPE) laminated composites were studied by drop-weight experiments. Laminated composites were fabricated with unidirectional UHMWPE prepreg using hot-pressing process. Laminated composites of size 150mm×100mm were subjected to low-velocity impact loading at three energy levels of 15J, 25J and 35J. It is found that the slops of load-time and energy-time curves increase with increase in the impact energy. However, load-time curve shows that there are some fluctuations before the peak load was reached. Peak load and absorbed energy increase with increasing impact energy. However, time to peak load decreases linearly with increasing impact energy.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

Low Velocity Impact Response of Small-Angle Laminated Composites

AIAA Journal ◽  
2006 ◽  
Vol 44 (12) ◽  
pp. 3080-3087 ◽  
Author(s):  
Adam L. Pilchak ◽  
Takashi Uchiyama ◽  
Dahsin Liu
Keyword(s):  
Small Angle ◽  
Laminated Composites ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact

The Efficiency of Auxetic Cores in Sandwich Beams Subjected to Low-Velocity Impact

2020 ◽  
Vol 12 (06) ◽  
pp. 2050061
Author(s):  
Mohammad Hedayatian ◽  
A. R. Daneshmehr ◽  
G. H. Liaghat
Keyword(s):  
Impact Energy ◽  
Test Procedure ◽  
Peak Load ◽  
Sandwich Beam ◽  
Low Velocity Impact ◽  
Sandwich Beams ◽  
Low Velocity ◽  
Velocity Impact ◽  
Unit Cells ◽  
Impact Area

This paper experimentally investigates the behavior of sandwich beam with auxetic core subjected to low-velocity impact loading. Two types of sandwich beams with different topologies of auxetic cellular cores were produced. Furthermore, a test procedure involving a cylindrical impactor was developed, and a parametric study was designed and performed. The results revealed that, at the same level of impact energy, the peak load decreased by increasing the re-entrant angle would make the auxetic sample with the highest re-entrant angle an ideal candidate for protective applications. However, in other applications where the structure needs to be protected from damage at a higher level of impact energy, the auxetic sample with the lowest re-entrant angle exhibited the best performance due to the highest amount of failure energy. Finally, the results showed that once the core structure changed from the conventional to auxetic, the energy level leading to damage to the structure increased so that it was escalated by a factor of 2 in the auxetic sample compared to the conventional sample. This is due to the negative Poisson’s ratio effect of structure that makes unit cells be drawn into the projectile impact area and, in turn, the structure is strengthened.

Effect of Foam Core Density and Facesheet Thickness on the Low Velocity Impact Response of Foam Core Sandwich Composites

2000 ◽  
Author(s):  
M. Motuku ◽  
R. M. Rodgers ◽  
S. Jeelani ◽  
U. K. Vaidya
Keyword(s):  
Impact Energy ◽  
Maximum Load ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Foam Core ◽  
Low Velocity ◽  
Core Density ◽  
Failure Characteristics ◽  
Velocity Impact ◽  
The Impact

Abstract The effect of foam core density and facesheet thickness on the low velocity impact response and damage evolution in homogeneous foam core sandwich composites was studied. The failure characteristics, initiation and evolution of damage as well as the effect of impact energy were investigated. A Dynatup 8210 Impact Test Machine was utilized to conduct the low-velocity impact tests. Characterization of the impact response was performed by comparing the impact load histories, impact plots and failure characteristics. Fractography analysis was conducted through the use of scanning electron microscopy (SEM) and optical microscopy. Three types of foam cores with different densities, namely Airlite B12.5, Rohacell IG-71R63 and Airex R63.5 foam cores, were used to study the effect of core density. Considering four groups of facesheets made of different layers of cross-ply carbon prepregs performed the effect of facesheet thickness. For all the facesheet thicknesses (0.011-0.894-cm thick) and impact energy (11-40 J) range considered in this study, the maximum load (Pm), deflection-at-maximum load (δm) and time-to-maximum load (tm) exhibited strong influence or dependence on the type of foam core as opposed to the facesheet thickness. The energy-to-maximum load (Em), total energy absorbed (Et) and total energy-to-impact energy (Et/Eimp) ratio became less sensitive on the foam core density (or type) with increasing facesheet thickness. A transition point from foam core to facesheet controlled impact behavior as a function of impact energy level was observed. The impact parameters varied either linearly or parabolically with impact energy depending on the impact energy level, type of foam core and facesheet thickness. Excellent repeatability of impact data was generally obtained with increase in foam core density.

Residual Strength and Failure Criterion of PP Thermoplastic Honeycomb Sandwich Subjected to Low Velocity Impact

2011 ◽  
Vol 471-472 ◽  
pp. 646-651 ◽  
Author(s):  
A. Freeda Amir ◽  
A.R. Othman
Keyword(s):  
Impact Energy ◽  
Residual Strength ◽  
Failure Modes ◽  
Structural Integrity ◽  
Peak Load ◽  
Low Velocity Impact ◽  
Honeycomb Core ◽  
Low Velocity ◽  
Velocity Impact ◽  
Damage Area

This paper presented the effect of constituent materials on impact damage and strength reduction of sandwich structure, composed of laminated woven E-glass facesheets and polypropylene thermoplastic honeycomb core. Effect of low-velocity impact was the main interest in a variety of layered configurations. Compression after impact (CAI) has been carried out to determine the residual strength of impacted sandwich structures. Three different thicknesses of core of 20, 40 and 60mm subjected to three different levels of impact energy of 15, 30 and 45J were investigated. Impact response of the panel was recorded and analyzed in terms of peak load, indentation, energy absorbed and time. A profile analysis using optical 3D surfaces profiler was carried out to attain the indentation depth and damage area of the samples. The tested samples were then sectioned into halves to capture the failure mode or damaged sequence of the polypropylene thermoplastic honeycomb core. The dominant failure modes of the core indicated that polypropylene thermoplastic honeycomb core is a high strength material which can absorb higher impact energy and retain a higher degree of structural integrity.

Effect of Graphene Platelets/Fiber on Plastics Nanocomposites under Low-Velocity Impact Response

2016 ◽  
Vol 852 ◽  
pp. 23-28
Author(s):  
S. Subha ◽  
Battu Sai Krishna ◽  
Dalbir Singh ◽  
R. Gokulnath
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Laminate Plate ◽  
Absorption Capacity ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Energy Absorption Capacity ◽  
Velocity Impact ◽  
The Impact

In this study, an attempt has made to explore the low-velocity impact response of a Carbon/epoxy laminate (CFRP) and E-Glass/epoxy laminates (GFRP). The composite was reinforced with Graphene Nanoplatelets (GnPs) and impact energy absorption capacity was studied. The plain GFRP and plain CFRP were served as a baseline for comparison. These composite laminate plates were fabricated using hand layup technique. The tests were carried out on the laminate plate as per ASTM D5628 FD. Impact tests were performed using a specially designed vertical drop-weight testing machine with an impactor mass of 1.926 kg. The result shows that laminate plate reinforced with GnPs reinforcement enhances the impact energy absorption capacity of the composites almost 4.5 % in the case Carbon/epoxy laminate and 3.5 % in the case of and E-glass/epoxy laminate. The enhanced impact resistance could be attributed to increased interlaminar fracture toughness of the fibres.

Effect of Impact Velocity and Impactor Mass on the Low Velocity Impact Response of Liquid Molding Vinyl Ester-350 Resin and Fiber-Reinforced Plaques

2000 ◽  
Author(s):  
M. Motuku ◽  
U. K. Vaidya ◽  
G. M. Janowski ◽  
G. Basappa ◽  
S. Jeelani
Keyword(s):  
Damage Evolution ◽  
Peak Load ◽  
Maximum Load ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact ◽  
Total Impact ◽  
Impact Duration

Abstract The influence of test conditions on the low velocity impact (LVI) response and damage evolution in neat resin plaques was investigated and documented. Specifically, the effect of impactor mass, velocity, and corresponding impact energy on the LVI response and damage evolution in unreinforced DERAKANE vinyl ester 411-350-resin system was studied. An instrumented drop weigh test machine was used to conduct the low velocity impact tests. The room temperature response of the material to impact loading and damage evolution was investigated using the impact load histories, impact plots and fractography analysis. This study is built upon previous work by the authors on LVI of neat resin systems, particularly those that have emerged as a new class of resins in liquid molding process. The study was motivated by the need for data and understanding of the failure characteristics of the individual constituents of a composite material such as in modeling of damage propagation and failure criteria analysis. For constant impact velocity, the time-to-maximum load (tm), total impact duration (tt), and the energy-to-maximum load to total energy absorbed (Em/Et) ratio increased, and energy absorbed after peak load (Ep) decreased with the mass of the impactor. For constant impactor mass, the time-to-maximum load and total impact duration decreased, the Em/Et ratio remained fairly the same, and energy absorbed after peak load increased with velocity; i.e., the impact velocity and mass had opposing effects on the time-to-maximum load, the total impact duration, Em/Et and energy absorbed after peak load. A single layer of plain-weave S2-glass fabric was incorporated in some of the unreinforced plaques in order to analyze the influence of reinforcement on the impact response and damage evolution. Insertion of a fabric layer aided in containment of the damage within the bounds of the specimen and to isolate the failure characteristics, which enabled further analysis of the impact response and damage evolution.

Influence of patch lay-up configuration and hybridization on low velocity impact and post-impact tensile response of repaired glass fiber reinforced plastic composites

2018 ◽  
Vol 53 (1) ◽  
pp. 3-17 ◽  
Author(s):  
J Jefferson Andrew ◽  
Sivakumar M Srinivasan ◽  
A Arockiarajan
Keyword(s):  
Glass Fiber ◽  
Impact Energy ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Static Tensile ◽  
The Impact

This paper aims to investigate the effect of homogenous and hybrid external patches based on plain weave woven glass and Kevlar fabric on low velocity impact and quasi-static tensile after impact response of adhesively bonded external patch repairs in damaged glass/epoxy composite laminates. In all hybrid patches, the proportion of Kevlar and glass fibers were equal (i.e. 50% of Kevlar and 50% of glass by volume fraction), while lay-up configuration was different. This further enables to study the associated effect of hybridization and lay-up configuration on impact response of the repaired laminates. The intent of using hybrid external patches is to combine the excellent high displacement-to-failure property of Kevlar fiber as a ductile reinforcement with the superior mechanical property of glass fiber as a brittle reinforcement. The effect of glass/Kevlar content on impact response and tensile after impact response was investigated for various incident impact energy levels, such as 2, 4, 6, and 8 J. Results showed that hybridization and lay-up configurations of the external patches played a significant role on low velocity impact and quasi-static tensile after impact response of the repaired glass/epoxy specimens. Specimens repaired using intra-ply hybrid patches showed better impact properties and damage tolerance capability than that of the virgin and other repaired specimens. In specific, the use of intra-ply hybrid patches reduced the impact energy absorption by 10.17% in comparison to the virgin specimens at impact energy of 8 J.

scholarly journals Experimental Investigation of Impactor Diameter Effect on Low-Velocity Impact Response of CFRP Laminates in a Drop-Weight Impact Event

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4131 ◽  
Author(s):  
Hongyi Cao ◽  
Mengyuan Ma ◽  
Mingshun Jiang ◽  
Lin Sun ◽  
Lei Zhang ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Internal Damage ◽  
Velocity Impact ◽  
Damage Characteristics ◽  
The Impact ◽  
Dent Depth ◽  
Delamination Area

The present study delved into the effect of impactor diameter on low velocity impact response and damage characteristics of CFRP. Moreover, the phased array ultrasonic technique (PAUT) was adopted to identify the impact damages based on double-sided scanning. Low-velocity impact tests were carried out using three hemispherical impactors with different diameters. The relationship of impact response and impactor diameters was analyzed by ultrasonic C-scans and S-scans, combined with impact response parameters. Subsequently, the damage characteristics were assessed in terms of dent depth, delamination area and extension shape via the thickness, and the relationships between absorbed energy, impactor displacement, dent depth and delamination area were elucidated. As revealed from experiment results, double-sided PAUT is capable of representing the internal damage characteristics more accurately. Moreover, the impactor diameter slightly affects the impact response under small impact energy, whereas it significantly affects the impact response under large impact energy.

Sign in / Sign up

Export Citation Format

Share Document