Design of Monitoring and Controlling Software of Footwear Sole Friction Based on QT

2012 ◽  
Vol 424-425 ◽  
pp. 1347-1351
Author(s):  
Yong Jie Yang ◽  
Xian Xian Lin ◽  
Dong Hua Lv
Keyword(s):  
Real Time ◽  
Coefficient Of Friction ◽  
Measurement Accuracy ◽  
Serial Communication ◽  
Safety Performance ◽  
Development Environment ◽  
Controlling System ◽  
Slip Resistance ◽  
The Coefficient Of Friction

Slip resistance of footwear sole affects the comfort and safety of shoes directly, and slip resistance is mainly expressed by the coefficient of friction. Within a certain range, the greater the coefficient of friction, the better the slip resistance. In order to determine the safety performance of shoes, the system will obtain the coefficient of friction by measuring the tension and pressure put on shoes, so it’s very important to do the measurement precisely. Based on QT development environment and Monitoring-controlling System of footwear sole friction, the software will execute real-time receiving, processing, controlling, displaying, drawing and saving collected data of tension and pressure via serial communication and finally on the basis of the system test to verify the correctness of the software and measurement accuracy

SURFACE MODIFICATION OF TPR SOLE: AN APPROACH TO IMPROVE SLIP RESISTANCE ON QUARRY AND CERAMIC TILES

2015 ◽  
Vol 88 (1) ◽  
pp. 163-175 ◽  
Author(s):  
R. Mohan ◽  
S. Raja ◽  
G. Saraswathy ◽  
B. N. Das
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Surface Modification ◽  
Surface Treatment ◽  
Coefficient Of Friction ◽  
Chemical Surface ◽  
Resistance Property ◽  
Slip Resistance ◽  
The Coefficient Of Friction ◽  
Trichloroisocyanuric Acid

ABSTRACT Human slip on smooth surfaces is a common accident, even though the footwear soling materials are designed with cleats and treads to provide more friction with the floor. About 20% of footwear is made with thermoplastic rubber (TPR; styrene-butadiene-styrene) soles. The slip resistance property under wet-flooring conditions of this kind of sole is poor because of the nonionic nature of the polymer. Chemical surface modification can be exploited to improve the slip-resistance property of TPR soles. The surface is chemically modified with trichloroisocyanuric acid in a methyl ethyl ketone medium (TCI/MEK; at 1, 2, and 3%) to introduce chlorinated and oxidized moieties to the rubber surface. The extent of surface modification produced in TPR with this change can be tested using attenuated total reflectance–Fourier transform infrared spectroscopy, scanning electron microscopy, and contact angle and surface roughness measurements. The improvement in slip resistance can be evaluated by measuring the coefficient of friction using a dynamic slip-resistance tester. The extent of the change in the functional physical properties, such as surface roughness, contact angle, work adhesion, in slip resistance can be improved by optimizing the concentration of trichloroisocyanuric acid. Physicomechanical properties of unmodified and modified soles that are essential for wear performance can be tested and compared. Quantitative changes on the surface of modified rubber soles increases surface roughness, reduces contact angles, and increases work energy, so there is a considerable increase in the coefficient of friction, especially under wet floor conditions. The chemical surface treatment tends to reduce the bulk mechanical properties, such as tensile strength, elongation at break, and abrasion resistance, because cyanuric acid attacks the sole. The coefficient of friction produces a positive trend at 1 and 2% TCI/MEK treatments, but the trend is negative at a 3% concentration. The optimum surface treatment level for surface modification to enhance the slip resistance of TPR is 2% TCI/MEK.

Desing of Real-Time Temperature Measurement System Based on Semiconductor Laser Diode

2014 ◽  
Vol 687-691 ◽  
pp. 886-889
Author(s):  
Zhong Shu Yang
Keyword(s):  
Temperature Measurement ◽  
Real Time ◽  
Laser Diode ◽  
Measurement System ◽  
Measurement Accuracy ◽  
Semiconductor Laser Diode ◽  
Large Size ◽  
Controlling System ◽  
Airplane Engine ◽  
Temperature Measurement System

Thermoelectric couple was employed in traditional airplane engine temperature measurement system with the disadvantages of large size,heavy weight,big error and slow response.This paper presents a new kind of real—time temperature measurement system using laser diode InGaAs/I as light source,and using pyroelectric detector LiTa03 as optical receiving unit and using a microprocessor as signal processing center.This instrument consists of three parts:optical emitting and receiving system,signal amplifying and controlling system,and display system。The principle and structure of the system are introduced.Experimental results of airplane engine real—time temperature measurement show that temperature measurement accuracy and response time conform to our requirement in the range of 300°C一800°Cand agree with prediction of theory.All these prove that the design is correct.

Slip Sliding Away — Slip Resistance of Athletic Socks on Indoor Flooring

2009 ◽  
Vol 53 (9) ◽  
pp. 568-571
Author(s):  
David G. Curry ◽  
Anne Mathias
Keyword(s):  
Coefficient Of Friction ◽  
Laboratory Study ◽  
Published Data ◽  
Slip Resistance ◽  
Significant Difference ◽  
The Coefficient Of Friction ◽  
Dry Conditions ◽  
Flooring Materials

A laboratory study was conducted to assess the slip resistance of athletic socks on various household flooring materials under both wet and dry conditions. While prior studies regarding slip resistance have focused on shod walkers, there is a lack of published data on the coefficient of friction between stocking-clad feet and indoor flooring. To investigate this, four types of athletic socks were tested on samples of eight flooring materials for both wet and dry conditions. These results were compared to tests of a Neolite slider pad on these floors. The results indicated that for socks on textured vinyl flooring, there was no significant difference in slip resistance between the wet and dry conditions, though there was a trend towards greater slip resistance under wet conditions. Generally, it appears that the likelihood of slipping on other types of wet indoor walking surfaces is lower when walking in socks rather than shoes.

REALIZING IoT BASED REAL TIME MONITORING AND CONTROLLING SYSTEM

2017 ◽  
Vol 4 (4) ◽  
pp. 20
Author(s):  
KAVITHA T. ◽  
PREETHI D. LAVANYA ◽  
SARANYA S. ◽  
ANCY EVERT P.M. JONAH ◽  
◽  
...  
Keyword(s):  
Real Time ◽  
Real Time Monitoring ◽  
Controlling System

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

scholarly journals Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4217
Author(s):  
Üsame Ali Usca ◽  
Mahir Uzun ◽  
Mustafa Kuntoğlu ◽  
Serhat Şap ◽  
Khaled Giasin ◽  
...  
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Practical Significance ◽  
Tribological Characteristics ◽  
M 10 ◽  
Wide Range ◽  
The Coefficient Of Friction ◽  
Four Levels

Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

scholarly journals Influence of Beam Power on Young’s Modulus and Friction Coefficient of Ti–Ta Alloys Formed by Electron-Beam Surface Alloying

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1246
Author(s):  
Stefan Valkov ◽  
Dimitar Dechev ◽  
Nikolay Ivanov ◽  
Ruslan Bezdushnyi ◽  
Maria Ormanova ◽  
...  
Keyword(s):  
Electron Beam ◽  
Young’S Modulus ◽  
Coefficient Of Friction ◽  
Young's Modulus ◽  
Beam Power ◽  
Surface Alloying ◽  
Surface Alloys ◽  
X Ray ◽  
The Coefficient Of Friction ◽  
Beam Surface

In this study, we present the results of Young’s modulus and coefficient of friction (COF) of Ti–Ta surface alloys formed by electron-beam surface alloying by a scanning electron beam. Ta films were deposited on the top of Ti substrates, and the specimens were then electron-beam surface alloyed, where the beam power was varied from 750 to 1750 W. The structure of the samples was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Young’s modulus was studied by a nanoindentation test. The coefficient of friction was studied by a micromechanical wear experiment. It was found that at 750 W, the Ta film remained undissolved on the top of the Ti, and no alloyed zone was observed. By an increase in the beam power to 1250 and 1750 W, a distinguished alloyed zone is formed, where it is much thicker in the case of 1750 W. The structure of the obtained surface alloys is in the form of double-phase α’and β. In both surface alloys formed by a beam power of 1250 and 1750 W, respectively, Young’s modulus decreases about two times due to different reasons: in the case of alloying by 1250 W, the observed drop is attributed to the larger amount of the β phase, while at 1750 W is it due to the weaker binding forces between the atoms. The results obtained for the COF show that the formation of the Ti–Ta surface alloy on the top of Ti substrate leads to a decrease in the coefficient of friction, where the effect is more pronounced in the case of the formation of Ti–Ta surface alloys by a beam power of 1250 W.

Reducing the Coefficient of Friction for Fast-Absorbing Gut Suture

2009 ◽  
Vol 35 (12) ◽  
pp. 2004 ◽  
Author(s):  
Jonathan Lee Bingham ◽  
Mariah R. Brown ◽  
Julian Ramsey Mellette
Keyword(s):  
Coefficient Of Friction ◽  
The Coefficient Of Friction
Sign in / Sign up

Export Citation Format

Share Document