Features and Industrial Applications of Combined Directed Valve Tray

2012 ◽  
Vol 443-444 ◽  
pp. 905-910
Author(s):  
Jie Xu Zhang ◽  
Cheng Fang Zhang

To increase the efficiency of float valve tray in plate column, a combined directed valve tray was developed. Comparative analysis of tray pressure drops, entrainments, weeping rates and mass transfers was conducted between the widely used V1-type float valve trays and the combined directed valve tray. The applications of the combined directed valve tray in atmospheric pressure device, catalytic cracking unit and gas fractionation device were also listed, which indicated that it was a significant improvement of float valve tray.

Heat exchangers are prominent industrial applications where engineering science of heat transfer and Mass transfer occurs. It is a contrivance where transfer of energy occurs to get output in the form of energy transfer. This paper aims at finding a solution to improve the thermal performance in a heat exchanger by using passive method techniques. This experimental and numerical analysis deals with finding the temperature outlets of cold and hot fluid for different mass flow rates and also pressure drop in the tube and the annular side by adding an elliptical leaf strip in the pipe at various angles. The single elliptical leaf used in experiment has major to minor axes ratios as 2:1 and distance of 50 mm between two leaves are arranged at different angular orientations from 0 0 to 1800 with 100 intervals. Since it’s not possible to find the heat transfer rates and pressure drops at every orientation of elliptical leaf so a generalized regression neural network (GRNN) prediction tool is used to get outputs with given inputs to avoid experimentation. GRNN is a statistical method of determining the relationship between dependent and independent variables. The values obtained from experimentation and GRNN nearly had precise values to each other. This analysis is a small step in regard with encomiastic approach for enhancement in performance of heat exchangers


2021 ◽  
Vol 625 (3) ◽  
pp. 28-31
Author(s):  
P. V. Kugatov ◽  
◽  
B. S. Zhirnov ◽  
A. E. Eremenko ◽  
◽  
...  

Samples of petroleum pitches were obtained from heavy pyrolysis resin and decantoil (heavy gas-oil of catalytic cracking) by thermal polycondensation at atmospheric pressure, temperatures of 380–400 and 410–440°С (for resin and decantoil, respectively) and isothermal holding time of 30–480 min. Analysis of the dependence of the softening point on the mesophase content for the obtained samples showed that at the same mesophase content, decantoil pitches exhibit a lower softening point compared to pyrolysis resin pitches, for which, even at 30 % mesophase, the softening point approaches 300°C. This suggests that it is impossible to obtain pitch from pyrolysis resin with high mesophase content without preliminary preparation (for example, by hydrogenation). On the other hand, it has been shown that for pitches from decantoil, it is possible to isolate the mesophase up to 65% or more with a softening point not higher than 250°C.


Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 455 ◽  
Author(s):  
Wasim Raza ◽  
Shakhawat Hossain ◽  
Kwang-Yong Kim

A wide range of existing passive micromixers are reviewed, and quantitative analyses of ten typical passive micromixers were performed to compare their mixing indices, pressure drops, and mixing costs under the same axial length and flow conditions across a wide Reynolds number range of 0.01–120. The tested micromixers were selected from five types of micromixer designs. The analyses of flow and mixing were performed using continuity, Navier-Stokes and convection-diffusion equations. The results of the comparative analysis were presented for three different Reynolds number ranges: low-Re (Re ≤ 1), intermediate-Re (1 < Re ≤ 40), and high-Re (Re > 40) ranges, where the mixing mechanisms are different. The results show a two-dimensional micromixer of Tesla structure is recommended in the intermediate- and high-Re ranges, while two three-dimensional micromixers with two layers are recommended in the low-Re range due to their excellent mixing performance.


Author(s):  
Thomas G. Shepard ◽  
John Wentz ◽  
Tucker Bender ◽  
Derek Olmschenk ◽  
Alex Gutenberg

Abstract Flow conduits made via additive manufacturing, commonly referred to as 3-D printing, are of increasing interest for a variety of industrial applications due to the ability to create unique and conformal flow paths that would not be possible with other fabrication techniques. Fused filament fabrication (FFF) is an additive manufacturing technique that is seeing new interest in the creation of internal flow channels with its ability to print high-temperature polymers and soluble supports. Printing parameter choices in the FFF printing process result in surfaces that can have significant profile differences that may significantly impact the flow characteristics within the conduits. In this study, two print parameters were experimentally studied for turbulent water flow through circular pipes created by fused filament fabrication out of acrylonitrile butadiene styrene (ABS). The print layer orientation relative to the flow was investigated for printing layers parallel, perpendicular, and at 45 degrees from the flow axis. Layer thickness were varied from 0.254 mm to 0.330 mm and all channels were created using soluble support structures. Pressure drops were measured for fully developed flow through pipes with an inside diameter of 5 mm and Reynolds numbers up to 62,000. Results are presented in terms of relative pressure drops as well as the wall surface roughness that would lead to such impacts. These flow-determined grain surface roughnesses are then compared against measurements of print surface roughness.


Author(s):  
Varan Gupta ◽  
Pulkit Sapra ◽  
Suman Muralikrishnan ◽  
M. Balakrishnan ◽  
P. V. M. Rao

Linear guides are extensively employed in several industrial applications. Miniaturization, minimal friction, cost efficiency and low maintenance are the major challenges faced while developing a linear motion system. This paper presents design and realization of such systems, overcoming the aforementioned challenges. Linear guidance mechanisms, suitable for implementing latching in Refreshable Braille Displays are proposed, where uniform behavior under eccentric loading is required. Several low cost, reliable and efficient guide mechanisms with predetermined dimensional constraints have been designed. Seven mechanisms are illustrated and analyzed in this paper, which includes both, traditional contact-based mechanisms and compliant mechanisms that offer contact-less motion. The paper further compares the functionality, cost feasibility and ease of manufacturing and assembly of these mechanisms.


Author(s):  
Christopher A. Vasko ◽  
Christina G. Giannopapa

Recently, cold, non-equilibrium atmospheric pressure plasmas (CAPs) and their active chemistry have been extensively investigated to the benefit of a wide array of applications such as biomedical and industrial applications mainly in the area of materials processing and chemical synthesis, amongst many others. In general, these plasmas operate at standard conditions (i.e. 1 atm, 300K), are small (∼ cm) and rather simple to operate in comparison to other plasmas. Their complex chemistry gives rise to a wide array of both stable and transient reactive species: such as O3, H2O2, OH and NOx, next to charged species and (V)UV-radiation. This chemistry is the reason for their wide spread application and has already found many industrial applications from waste water treatment, stain free detergents and industrial scale production of oxidants. In recent years, bactericidal effects of CAPs gained increasing attention for applications such as dermatology, disinfection, dentistry and cancer treatment or stimulated blood coagulation. This paper aims to highlight recent research into new biological applications for complex mission scenarios involving humans in remote locations using CAPs for disinfection, bleaching or wound healing. Results using radiofrequency plasma jets for the inactivation of Pseudomonas aeruginosa are summarized, highlighting the importance of liquid plasma interactions. Work with such a CAP paved the way for a promising application in the field of biomedical applications presented here. It involves surface barrier discharges which can be used to treat larger surfaces compared to jets. Their physical construction, using floating or contained electrodes, offer a convenient way of controlling electrical current on a large scale, 3D treatment of both conducting and insulating surfaces with minimal heating. These devices may be tailored to specific skin treatments, allowing fast and effective treatment of larger skin surfaces while following the shape of the skin. This might reduce the need for bactericidal agents and would be a valuable application to assist humans in remote locations. These emerging technologies could be essential both for human health care under extreme conditions, as well as for research itself (sterilisation of tools and large areas, etc.). Especially in the absence of abundant resources (antibiotic agents, disinfectants and the like) alternative approaches to support humans in isolated locations have to be developed. Applications based on a good understanding of plasma chemistry would empower health care under extreme conditions to efficiently use and manage in situ resources. Their low mass, compact size, low power consumption and high reliability could make them essential use under extreme conditions.


2017 ◽  
Vol 888 ◽  
pp. 485-490
Author(s):  
Tengku Sharifah Marliza ◽  
Mohd Ambar Yarmo ◽  
Azizul Hakim ◽  
Maratun Najiha Abu Tahari ◽  
Yun Hin Taufiq-Yap

Supported ionic liquid (IL) [bmim][CF3SO3] on SiO2 was prepared, characterized and its potential evaluated for CO2 capture via adsorption and desorption studies using gas adsorption analyzer. The physical and chemical properties were determined using N2 adsorption/desorption and CO2-TPD analysis. The increasing IL loading caused a drastic decrease in the surface area as well as pore volume due to the confinement of IL within the micropore and mesopore area. However, the increasing IL loading increased the basicity of the sorbent which significantly enhanced CO2 chemisorption. Supported [bmim][CF3SO3] on SiO2 revealed the physical and chemical adsorption of CO2 and resulted in a remarkable CO2 adsorption capacity at atmospheric pressure and room temperature (66.7 mg CO2/gadsorbent) which has great potential in industrial applications.


Sign in / Sign up

Export Citation Format

Share Document