Effects of Ramp Rates with Short Holding Time on the Sinterability of Hydroxyapatite

2012 ◽  
Vol 545 ◽  
pp. 229-234
Author(s):  
Lai Kuan Lee Samuel ◽  
Chou Yong Tan ◽  
Ramesh Singh ◽  
Boon Kar Yap ◽  
Ranna Tolouei ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Human Bone ◽  
Holding Time ◽  
Ramp Rate ◽  
The Poor ◽  
Bone Replacement ◽  
Sample Characterization

Hydroxyapatite (HA) is by far the closest match to the human bone in terms of chemical composition. Furthermore, HA boasts excellent biocompatibility thus earning its reputation for human bone replacement. However, HA lacks desirable mechanical properties (i.e. hardness, fracture toughness, etc.). Due to the poor heat conductivity of ceramics, it is hypothesized that HA when sintered via conventional pressureless sintering, smaller ramp rates are advantageous as oppose to larger ramp rates. These advantages can be observed as improved densification along with improved mechanical properties. In the present work, the sintering profile for the HA green bodies were held at 1 minute in comparison to the usual 2 hours holding time. The applied ramp rates were 2 °C/min, 5 °C/min and 10 °C/min. Sintering temperatures were set to 1000, 1100, 1200, and 1300 °C. Sample characterization was then reviewed in the aspects of phase stability, % shrinkage, bulk and relative density, Young’s modulus, Vickers hardness, as well as fracture toughness. The results revealed that sintering with shorter holding time yielded an improvement in the mechanical properties of HA. It was observed that sintering HA with a 2 °C/min ramp rate does not result in the formation of extrageneous phases even when sintered to 1300 °C. Similarly at 2 °C/min and 1300 °C, densification was observed to be 99.05 %. In addition, Young’s modulus recorded its highest value (117.03 GPa) when sintered with a ramp rate of 2°C/min. It was also observed that sintering HA at a ramp rate of 2°C/min produced a hardness value of 5.88 GPa (improvement of 0.68 GPa when compared with 2 hours holding time).

Effect of Temperature and Holding Time on Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 11-18
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Young’S Modulus ◽  
Sintering Temperature ◽  
Young's Modulus ◽  
Holding Time ◽  
Effect Of Temperature ◽  
Two Stage ◽  
Pinning Effect ◽  
Zirconia Toughened Alumina

The microstructure and mechanical properties of Zirconia Toughened Alumina (ZTA) produced via two-stage sintering at various sintering temperature of T1 and T2 in addition to effect of various holding time were investigated. T1 temperature was set between the range of 1400°C to 1500°C with a heating rate of 20°C/min. The samples were then sintered at T2 ranging from 1350°C to 1400°C followed by various holding time between 2 hours to 12 hours. The sintered samples’ microstructural properties, bulk density, hardness (Vickers hardness), elastic modulus (Young’s modulus) and fracture toughness (K1C) were then determined. Compared to standard holding time of two-stage sintering which is 12 hours, results show that ZTA produced via two-stage sintering with shorter holding time of 4 hours with T1 set at 1500°C and T2 of 1450°C are capable of achieving full densification. In addition, the same sample were also able to achieve hardness up to 19 GPa, Young’s modulus of 390 GPa and fracture toughness of 6.1 MPam1/2. The improvement in mechanical properties can be mainly attributed to the absent of surface diffusion at T2 above 1400°C and also presence of Y-TZP which contributed to lower grain growth due to the pinning effect.

The Effect of Sintering Profiles on Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 904 ◽  
pp. 174-180
Author(s):  
Teow Hsien Loong ◽  
Sivakumar Sivanesan ◽  
Se Yong Eh Noum
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Bulk Density ◽  
Young’S Modulus ◽  
Heating Rate ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Holding Time ◽  
Two Stage ◽  
Zirconia Toughened Alumina

The effects of sintering profiles on the Zirconia Toughened Alumina (ZTA) composite containing 0 vol% Y-TZP (pure alumina) to 20 vol% Y-TZP content prepared by a sintering method known as two-stage sintering were investigated. The heating rate was set between 10°C/min to 20°C/min, T1 set between 1400°C to 1500°C, T2 at 1350°C and holding time was set at 12 hours. The samples’ microstructural properties and mechanical properties, including bulk density, Vickers hardness, Young’s modulus and fracture toughness, were evaluated. Based on the data obtained, the ZTA composites with 10 vol% Y-TZP sintered at a heating rate of 10°C/min and holding time of 12 hours were able to achieve mechanical properties requirements set by the industry standard. In addition, the maximum ZTA composite’s bulk density was recorded to be above 90% T.D, while the Vickers hardness of the composite was recorded to be exceeding 17 GPa. The ZTA composite also recorded maximum Young’s modulus exceeding 380 GPa and fracture toughness above 6 MPam1/2.

scholarly journals Effects of CNT Addition on Mechanical Properties, Electric Conductivity and Oxidation Resistance of Al2O3-TiC Composite

2013 ◽  
Vol 761 ◽  
pp. 83-86
Author(s):  
Hideaki Sano ◽  
Junichi Morisaki ◽  
Guo Bin Zheng ◽  
Yasuo Uchiyama
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Electric Conductivity ◽  
Young’S Modulus ◽  
Oxidation Resistance ◽  
Young's Modulus ◽  
Tic Particle

Effects of carbon nanotubes (CNT) addition on mechanical properties, electric conductivity and oxidation resistance of CNT/Al2O3-TiC composite were investigated. It was found that flexural strength, Young’s modulus and fracture toughness of the composites were improved by addition of more than 2 vol%-CNT. In the composites with more than 3 vol%-CNT, the oxidation resistance of the composite was degraded. In comparison with Al2O3-26vol%TiC sample as TiC particle-percolated sample, the Al2O3-12vol%TiC-3vol%CNT sample, which is not TiC particle-percolated sample, shows almost the same mechanical properties and electric conductivity, and also shows thinner oxidized region after oxidation at 1200°C due to less TiC in the composite.

Local Mechanical Properties of Highly Porous Si3N4 for Trabecular Bone Replacement

2015 ◽  
Vol 662 ◽  
pp. 142-146
Author(s):  
Zuzana Pramuková Vilčeková ◽  
Monika Kašiarová ◽  
Magdaléna Precnerová Domanická ◽  
Miroslav Hnatko ◽  
Pavol Šajgalík
Keyword(s):  
Mechanical Properties ◽  
Silicon Nitride ◽  
Yield Strength ◽  
Trabecular Bone ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Polyurethane Foams ◽  
Strength Increase ◽  
Bone Replacement ◽  
Highly Porous

The study deals with the development of highly porous undegradable ceramics based on silicon nitride as potential replacement of trabecular bone. These materials were produced using replication method with polyurethane foams as pore-forming agents to achieve similar porous structure to trabecular bone. Prepared porous ceramics had a bimodal pore structure with macro-pores larger than 200 μm and micro-pores smaller than 1 μm in diameter, which are necessary for tissue ingrowths, cell adhesion, adsorption of biological metabolites and nutrition delivery in organism. The microstructure and local mechanical properties (Young’s modulus and Yield strength) were evaluated and compared with human trabecular bone. Results showed that studied porous materials have satisfactory porosity and pore sizes for trabecular bone replacement. Young’s modulus of bone was 12.6 ± 2.23 GPa and porous silicon nitride samples ranged from 10.9 ± 3.38 GPa to 12.9 ± 1.13 GPa. The values of Yield strength of trabecular bone was determined as 493 ± 30.7 MPa and the values of porous samples varied from 250 ± 19.3 MPa to 558 ± 36.5 MPa. Young’s modulus and Yield strength increase with increasing of the pre-sintering temperature and multiple infiltrations.

Mechanical Properties of Transparent Polycrystalline Silicon Nitride

2006 ◽  
Vol 317-318 ◽  
pp. 305-308 ◽  
Author(s):  
Rak Joo Sung ◽  
Takafumi Kusunose ◽  
Tadachika Nakayama ◽  
Yoon Ho Kim ◽  
Tohru Sekino ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
Young’S Modulus ◽  
Fracture Strength ◽  
Polycrystalline Silicon ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Β Phase ◽  
Α Phase

A novel transparent polycrystalline silicon nitride was fabricated by hot-press sintering with MgO and AlN as additives. The mixed powder with 3 wt.% MgO and 9 wt.% AlN was sintered at 1900oC for 1 hour under 30 MPa pressure in a nitrogen gas atmosphere. Transparent polycrystalline silicon nitride was successfully fabricated. The mechanical properties such as density, hardness, young’s modulus, fracture strength and fracture toughness were evaluated. The effect of α/β phase on the mechanical properties of transparent polycrystalline silicon nitride was investigated. The properties were changed depending on the amount of α/β phase. The hardness and Young's modulus increased with increasing the volume fraction of α-phase fraction as a reflection of the higher hardness of α-phase Si3N4. The fracture toughness and fracture strength decreased with decreasing the volume fraction of β-phase Si3N4.

Densification Behaviour and Mechanical Properties on MgO Doped Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 3-10
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Total Hip Arthroplasty ◽  
Young’S Modulus ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Two Stage ◽  
Positive Effect ◽  
Zirconia Toughened Alumina

The effect of doping small amounts of Magnesium Oxide ranging between 0 to 1 vol% on Zirconia Toughened Alumina (ZTA) composites which is one of main biomaterial used for production of total hip arthroplasty were investigated. The samples were produced via conventional two-stage sintering with T1 varies between 1450°C and 1550°C with heating rate of 20°C/min. The samples were then rapid cooled to T2 set at 1400°C with holding time of 12 hours. The microstructural and mechanical properties of the two-stage sintered ZTA are then investigated to determine the feasibility of MgO addition. Combination of two-stage sintering at T1 above 1500 and also small amount of MgO up to 0.5 vol% were shown to have positive effect on ZTA which exhibited improvement on its grain size, mechanical properties such as Vickers hardness, Young’s modulus and fracture toughness compared to undoped ZTA composites. The sample with 0.5 vol% MgO addition sintered at T1 of 1500°C and T2 1400°C was able to achieve Vickers hardness of 19.6 GPa, Young’s modulus of 408 GPa and fracture toughness of 6.8 MPam1/2 without significant grain growth compared to undoped ZTA composites.

scholarly journals Investigation of Nano-Mechanical and- Tribological Properties of Hydrogenated Diamond Like Carbon (DLC) Coatings

2016 ◽  
Vol 33 (6) ◽  
pp. 769-776 ◽  
Author(s):  
Y.-R. Jeng ◽  
S. Islam ◽  
K-T. Wu ◽  
A. Erdemir ◽  
O. Eryilmaz
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Friction Coefficient ◽  
Young’S Modulus ◽  
Tribological Properties ◽  
Young's Modulus ◽  
Chemical Vapour ◽  
Diamond Like Carbon ◽  
Dlc Coatings ◽  
Mechanical And Tribological Properties

AbstractHydrogenated diamond like Carbon (H-DLC) is a promising lubricious coating that attracted a great deal of interest in recent years mainly because of its outstanding tribological properties. In this study, the nano-mechanical and -tribological properties of a range of H-DLC films were investigated. Specifically, four kinds of H-DLC coatings were produced on Si substrates in pure acetylene, pure methane, 25% methane + 75% hydrogen, 50% methane + 50% hydrogen discharge plasmas using a plasma enhanced chemical vapour deposition (PECVD) system. Nano indentation was performed to measure the mechanical properties such as hardness and young's modulus and nanoscartching was performed to investigate the frictional behavior and wear mechanism of the H-DLC samples in open air. Moreover, Vickers indentation method was utilized to assess the fracture toughness of the samples. The results revealed that there is a strong correlation between the mechanical properties (hardness, young's modulus, fracture toughness) and the friction coefficient of DLC coatings and the source gas chemistry. Lower hydrogen to carbon ratio in source gas leads to higher hardness, young's modulus, fracture toughness and lower friction coefficient. Furthermore, lower wear volume of the coated materials was observed when the friction coefficient was lower. It was also confirmed that lower hydrogen content of the DLC coating leads to higher wear resistance under nanoscratch conditions.

The Effect of Pressure and Pore-Forming Agent on the Mechanical Properties of Porous Titanium

2011 ◽  
Vol 217-218 ◽  
pp. 1191-1196
Author(s):  
Peng Zhang ◽  
Yuan Chen Qi ◽  
Wei Li
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Cortical Bone ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Porous Titanium ◽  
Human Bone ◽  
Cold Isostatic Press ◽  
Effect Of Pressure ◽  
Porous Ti

Porous titanium compacts were fabricated by powder metallurgy using cold isostatic press with and without pore forming agents. Their microstructure and mechanical properties were investigated in this study. These alloy powders were sintered under 1300°C in vacuum of 10-3 Pa for 2h, followed by furnace cooling. Young’s modulus of sintered Ti could equal that of human’s dense bones. It was found that the strength of porous Ti enhanced by increasing the pressure or decreasing the amounts of pore forming agents. We prepared a porous pure Ti with 30wt.% NH4HCO3 as pore forming agents whose modulus was near to the human cortical bone, as compared in the range from 10 to 30GPa of Young’s modulus for human bone.

Densification, Microstructure, and Behavior of Hydroxyapatite Ceramics Sintered by Using Spark Plasma Sintering

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Shufeng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Young’S Modulus ◽  
Spark Plasma Sintering ◽  
Young's Modulus ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature And Pressure

This paper discusses the dependence of the mechanical properties and microstructure of sintered hydroxyapatite (HA) on the sintering temperature and pressure. A set of specimens was prepared from as-received HA powder and sintered by using a spark plasma sintering (SPS) process. The sintering pressures were set at 22.3MPa, 44.6MPa, and 66.9MPa, and sintering was performed in the temperature range from 800°Cto1000°C at each pressure. Mechanisms underlying the interrelated temperature-mechanical and pressure-mechanical properties of dense HA were investigated. The effects of temperature and pressure on the flexural strength, Young’s modulus, fracture toughness, relative density, activation energy, phase stability, and microstructure were assessed. The relative density and grain size increased with an increase in the temperature. The flexural strength and Young’s modulus increased with an increase in the temperature, giving maximum values of 131.5MPa and 75.6GPa, respectively, at a critical temperature of 950°C and 44.6MPa, and the fracture toughness was 1.4MPam1∕2 at 1000°C at 44.6MPa. Increasing the sintering pressure led to acceleration of the densification of HA.

Sign in / Sign up

Export Citation Format

Share Document