The Preparation and Mechanical Property Study of Aluminum Borate Whisker/Phosphate Chrome-Alumina Wave-Transparent Composites

2012 ◽  
Vol 627 ◽  
pp. 819-822
Author(s):  
You Ping Wang ◽  
Jing Song Liu
Keyword(s):  
Mechanical Property ◽  
Tensile Strength ◽  
Image Analysis ◽  
Composite Material ◽  
Curing Time ◽  
Aluminum Borate ◽  
Coating Method ◽  
Transparent Composites ◽  
Transparent Materials

Wave-transparent materials of aluminum borate whisker/phosphate chrome-alumina are synthesized through coating method. It is found that, from the TG-DSC image analysis, there are two endothermic peaks at 120 °C and 180 °C, respectively. Pressure and curing time at this temperature should be increased. The flexural and tensile strength of the composite material reach the maximum when the content of aluminum borate whiskers is 6%.

Preparation and properties of polyurethane coatings modified by polysilazane

2019 ◽  
Vol 32 (6) ◽  
pp. 611-619 ◽  
Author(s):  
Xiaoli Liu ◽  
Zhen Ge ◽  
Wenguo Zhang ◽  
Yunjun Luo
Keyword(s):  
Mechanical Property ◽  
Photoelectron Spectroscopy ◽  
Composite Coatings ◽  
Composite Films ◽  
Dip Coating ◽  
Water Contact ◽  
Research Attention ◽  
Elongation At Break ◽  
Coating Method ◽  
Dip Coating Method

Due to their unique physicochemical properties, polysilazanes exhibit excellent performance when combined with some resin matrixes, which had drawn great research attention. In this article, polyurethane (PU) was firstly prepared by polytetrahydrofuran glycol, isophorone diisocyanate, and 1,4-butanediol as main materials. Then, the prepared PU was blended with polysilazane by mixing the two solutions together, which was cured to films via dip-coating method at room temperature. The structure, thermal stability, and surface properties of the composite coatings were investigated by Fourier-transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and X-ray photoelectron spectroscopy. The results demonstrated that after modification with polysilazane, the heat resistance, hydrophobicity, and mechanical property of the PU coatings were improved. When the content of polysilazane was 6 wt%, the mechanical property of the composite films was optimized, with a maximum tensile strength of 25.7 MPa and elongation at break of 797%. Meanwhile, the water contact angle of the composite film was 107° and the water absorption reached a minimum of 2.1%, which showed improved hydrophobicity and water resistance.

Mechanical Property of Phosphoaluminate Cement

2010 ◽  
Vol 150-151 ◽  
pp. 1754-1757 ◽  
Author(s):  
Peng Liu ◽  
Zhi Wu Yu ◽  
Ling Kun Chen ◽  
Zhu Ding
Keyword(s):  
Mechanical Property ◽  
Compressive Strength ◽  
Phase Composition ◽  
Electrical Properties ◽  
Pore Size Distribution ◽  
Pore Size ◽  
High Strength ◽  
Curing Time ◽  
Hydration Products ◽  
Resistance Value

The influence of curing time on the mechanical property of the phosphoaluminate cement (PAC) was investigated, and the mechanism was discussed as well. The phase composition and morphology of hydration products, electrical properties, porosity and pore size distribution of PAC cured different age were analyzed with XRD, EIS and MIP. The results showed PAC has the property of early-high strength, and the compressive strength of PAC cured for 1 day was about 70% of 28 days’. The main hydration products of PAC are micro-crystal phase and gel of phosphate and phosphoaluminate which formed compacter microstructure. In addition, there are no calcium hydroxide (CH) and ettringite (AFt) produced during the process of hydration. The compressive strength of PAC increased with age, which was due to more products continuously produced. The ac resistance analysis manifested as the change of the nyquist pattern and resistance value.

Using Embossing to Create a Fiber Reinforced Honeycomb Composite

2005 ◽  
Vol 127 (2) ◽  
pp. 257-262 ◽  
Author(s):  
William Jordan
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Carbon Fibers ◽  
Flexural Modulus ◽  
Testing Machine ◽  
Charpy Impact ◽  
Tensile Tests ◽  
Hydraulic Testing ◽  
Charpy Impact Toughness ◽  
Bend Tests

This research project used hot embossing to create a strong and tough polymeric based composite structure. A honeycomb type structure was created by pressing small grooves into thin polycarbonate sheets. A trapezoidal die was used to create hexagonal shaped channels in the polymeric sheet. A number of these sheets were then bonded together to form a composite material. Carbon fibers were embedded into the channels in some of the laminates. The embossing process was carried out at an elevated temperature in an environmental chamber attached to an MTS servo hydraulic testing machine. The grooved structure had a 31% to 45% decrease in the apparent density compared to the ungrooved specimens. Bend tests, tensile tests, and Charpy impact tests were performed on laminates made from this material. The specific values of tensile strength, flexural modulus, and Charpy impact toughness were increased. A small percentage of fibers significantly increased both the stiffness and strength of the laminate.

Effect of Quaternary Ammonium-Modified Montmorillonites on Mechanical Properties of Polypropylene

1998 ◽  
Vol 520 ◽  
Author(s):  
Y. H. Zhang ◽  
K. C. Gong
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Tensile Strength ◽  
Impact Strength ◽  
Quaternary Ammonium ◽  
Small Addition ◽  
Pp Composites ◽  
Addition Amount

ABSTRACTHybrids of quaternary ammonium-modified montmorillonites and polypropylene were prepared by melting intercalation. Results of mechanical property measurements show that, tensile strength, modulus and impact strength of PP composites are greatly enhanced simultaneously by a small addition amount of modified montmorillonites.

Effect of Fiber Orientation on the Tensile Strength in Fiber-Reinforced Polymeric Composite Materials

2005 ◽  
Vol 297-300 ◽  
pp. 2897-2902 ◽  
Author(s):  
Jin Woo Kim ◽  
Jung Ju Lee ◽  
Dong Gi Lee
Keyword(s):  
Tensile Strength ◽  
Composite Material ◽  
Fiber Orientation ◽  
Polymeric Composite ◽  
Orientation Distribution ◽  
Fiber Content ◽  
Fiber Reinforced ◽  
Composite Sheet ◽  
Content Ratio ◽  
Fiber Orientation Distribution

The study for strength calculation of one way fiber-reinforced composites and the study measuring precisely fiber orientation distribution were presented. However, because the DB that can predict mechanical properties of composite material and fiber orientation distribution by the fiber content ratio was not constructed, we need the systematic study for that. Therefore, in this study, we investigated what effect the fiber content ratio and fiber orientation distribution have on the strength of composite sheet after making fiber reinforced polymeric composite sheet by changing fiber orientation distribution with the fiber content ratio. The result of this study will become a guide to design data of the most suitable parts design or fiber reinforced polymeric composite sheet that uses the fiber reinforced polymeric composite sheet in industry spot, because it was conducted in terms of developing products. We studied the effect the fiber orientation distribution has on tensile strength of fiber reinforced polymeric composite material and achieved this results below. We can say that the increasing range of the value of fiber reinforced polymeric composite’s tensile strength in the direction of fiber orientation is getting wider as the fiber content ratio increases. It shows that the value of fiber reinforced polymeric composite’s tensile strength in the direction of fiber orientation 90° is similar with the value of polypropylene’s intensity when fiber orientation function is J= 0.7, regardless of the fiber content ratio. Tensile strength of fiber reinforced polymeric composite is affected by the fiber orientation distribution more than by the fiber content ratio.

Mechanical Properties and Microstructure Evolution of Typical Over-Aging State Al-Zn-Mg-Cu Alloy during Thermal Exposure

2021 ◽  
Vol 1026 ◽  
pp. 84-92
Author(s):  
Tao Qian Cheng ◽  
Zhi Hui Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Property ◽  
Electrical Conductivity ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Thermal Exposure ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Thermal Stability Of

Al-Zn-Mg-Cu alloy have been widely used in aerospace industry. However, there is still a lack of research on thermal stability of Al-Zn-Mg-Cu alloy products. In the present work, an Al-Zn-Mg-Cu alloy with T79 and T74 states was placed in the corresponding environment for thermal exposure experiments. Performance was measured by tensile strength, hardness and electrical conductivity. In this paper, precipitation observation was analyzed by transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HREM). The precipitations of T79 state alloy were GPⅡ zone, η' phase and η phase while the ultimate tensile strength, hardness and electrical conductivity were 571MPa, 188.2HV and 22.2MS×m-1, respectively. The mechanical property of T79 state alloy decreased to 530MPa and 168.5HV after thermal exposure. The diameter of precipitate increased and the precipitations become η' and η phase at the same time. During the entire thermal exposure, T74 state alloy had the same mechanical property trend as T79 state alloy. The precipitate diameter also increased while the types of precipitate did not change under thermal exposure. The size of precipitates affected the choice of dislocation passing through the particles to affect the mechanical properties.

Effect of Shortened Light-Curing Modes on Bulk-Fill Resin Composites

2020 ◽  
Vol 45 (5) ◽  
pp. 496-505
Author(s):  
CS Sampaio ◽  
PG Pizarro ◽  
PJ Atria ◽  
R Hirata ◽  
M Giannini ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Light Output ◽  
High Mode ◽  
Resin Composites ◽  
Curing Time ◽  
Micro Computed Tomography ◽  
Polymerization Shrinkage ◽  
Light Curing

Clinical Relevance Shortened light curing does not affect volumetric polymerization shrinkage or cohesive tensile strength but negatively affects the shear bond strength of some bulk-fill resin composites. When performing shortened light curing, clinicians should be aware of the light output of their light-curing units. SUMMARY Purpose: To evaluate volumetric polymerization shrinkage (VPS), shear bond strength (SBS) to dentin, and cohesive tensile strength (CTS) of bulk-fill resin composites (BFRCs) light activated by different modes. Methods and Materials: Six groups were evaluated: Tetric EvoCeram bulk fill + high mode (10 seconds; TEC H10), Tetric EvoFlow bulk fill + high mode (TEF H10), experimental bulk fill + high mode (TEE H10), Tetric EvoCeram bulk fill + turbo mode (five seconds; TEC T5), Tetric EvoFlow bulk fill + turbo mode (TEF T5), and experimental bulk fill + turbo mode (TEE T5). Bluephase Style 20i and Adhese Universal Vivapen were used for all groups. All BFRC samples were built up on human molar bur-prepared occlusal cavities. VPS% and location were evaluated through micro–computed tomography. SBS and CTS tests were performed 24 hours after storage or after 5000 thermal cycles; fracture mode was analyzed for SBS. Results: Both TEC H10 and TEE H10 presented lower VPS% than TEF H10. However, no significant differences were observed with the turbo-curing mode. No differences were observed for the same BFRC within curing modes. Occlusal shrinkage was mostly observed. Regarding SBS, thermal cycling (TC) affected all groups. Without TC, all groups showed higher SBS values for high mode than turbo mode, while with TC, only TEC showed decreased SBS from high mode to turbo modes; modes of fracture were predominantly adhesive. For CTS, TC affected all groups except TEE H10. In general, no differences were observed between groups when comparing the curing modes. Conclusions: Increased light output with a shortened curing time did not jeopardize the VPS and SBS properties of the BFRCs, although a decreased SBS was observed in some groups. TEE generally showed similar or improved values for the tested properties in a shortened light-curing time. The VPS was mostly affected by the materials tested, whereas the SBS was affected by the materials, curing modes, and TC. The CTS was not affected by the curing modes.

Sign in / Sign up

Export Citation Format

Share Document