A Novel Planar Extended Doublet Filter with Substrate Integrated Waveguide Cavity Resonators

2013 ◽  
Vol 631-632 ◽  
pp. 962-966
Author(s):  
Kai Shen ◽  
Tao Li ◽  
Jing Jing Wang
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Single Layer ◽  
Substrate Integrated Waveguide ◽  
Cavity Resonators ◽  
Transmission Zeros ◽  
Measurement Results ◽  
Negative Coupling ◽  
First Time

A novel planar extended doublet filter based on substrate Integrated waveguide cavity resonators was proposed for the first time. This filter consists of a main doublet with an additional resonator grown in one of the branches. The source and load are coupled to both branches of the doublet in order to generate two transmission zeros. By employing the combinational structure of the TE101-mode and TE102-mode of the SIW cavity resonators, the negative coupling coefficient required for the design of a single-layer cross-coupled SIW bandpass filter is implemented. The measurement results show the return loss of the implemented filter is above 13dB, the insertion loss is below 4.238dB with only 0.56% of the bandwidth.

scholarly journals CASCADED SQUARE LOOP BANDPASS FILTER WITH TRANSMISSION ZEROS FOR LONG TERM EVOLUTION (LTE)

SINERGI ◽  
2018 ◽  
Vol 22 (1) ◽  
pp. 63
Author(s):  
Iis Andini ◽  
Dian Widi Astuti ◽  
Muslim Muslim
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
External Resonator ◽  
Transmission Zeros ◽  
Term Evolution ◽  
Compact Size ◽  
Measurement Results ◽  
Resonator Method

In this paper, we present a bandpass filter that passed frequency of 1.7 GHz – 1.8 GHz. It is applied for an uplink frequency in 4G 1800MHz. This filter is created by using substrate PCB TMM-10i and has a compact size of 42 mm x 42 mm. The compact size is also important besides selectivity. The selectivity is achieved by implementing cascade square loop resonator method which generated transmission zeros. Actually, transmission zeros are obtained from the coupled resonator. The bandpass filter is designed by adding an external resonator on each square of the resonator loop and a patch to the inside of the square loop resonator. The parameter performances are simulated by HFSS. The parameter performances for return loss value is 14.24 dB at frequency 1.75 GHz and insertion loss value is 0.65 dB at frequency 1.75 GHz. By using VNA Anritsu MS 2026A, prototype bandpass filter is measured. The measurement results for return loss value is 6.8 dB and insertion loss value is 2.2 dB.

scholarly journals A Bandpass Filter Using Half Mode SIW Structure with Step Impedance Resonator

Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 51
Author(s):  
Min-Hang Weng ◽  
Chin-Yi Tsai ◽  
De-Li Chen ◽  
Yi-Chun Chung ◽  
Ru-Yuan Yang
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Filter Design ◽  
Design Concept ◽  
Center Frequency ◽  
Substrate Integrated Waveguide ◽  
Design Curve ◽  
Transmission Zeros ◽  
Measured Response

This paper presents a miniaturized bandpass filter, which uses half mode substrate integrated waveguide (HMSIW) structure with embedded step impedance structure (SIS). By embedding the stepped impedance structure into the top metal of the waveguide cavity, the center frequency can be quickly shifted to a lower frequency. The operating center frequency of the proposed bandpass filter (BPF) using HMSIW resonators with embedded SIS is tunable as functions of the parameters of the SIS. The design curve is provided. A filter example of the center frequency of the filter at 3.5 GHz is fabricated and measured, having the insertion loss |S21| less than 3 dB, and the return loss |S11| greater than 10 dB. The transmission zeros are located at 2.95 GHz and 3.95 GHz on both sides of the passband, both of which are lower than 30 dB. The simulation result and the measured response conform to the proposed design concept. The proposed HMSIW filter design is in line with the current 5G communication trend.

scholarly journals Substrate integrated waveguide bandpass filter for short range device application using rectangular open loop resonator

2021 ◽  
Vol 11 (5) ◽  
pp. 3747
Author(s):  
Dian Widi Astuti ◽  
Rizki Ramadhan Putra ◽  
Muslim Muslim ◽  
Mudrik Alaydrus
Keyword(s):  
Short Range ◽  
Return Loss ◽  
Bandpass Filter ◽  
Open Loop ◽  
Frequency Region ◽  
Substrate Integrated Waveguide ◽  
Network Analyzer ◽  
Measurement Results ◽  
Simulation Results ◽  
Good Agreement

The substrate integrated waveguide (SIW) structure is the candidate for many application in microwave, terahertz and millimeter wave application. It because of SIW structure can integrate with any component in one substrate than others structure. A kind components using SIW structure is a filter component, especialy bandpass filter. This research recommended SIW bandpass filter using rectangular open loop resonator for giving more selectivity of filter. It can be implemented for short range device (SRD) application in frequency region 2.4 - 2.483 GHz. Two types of SIW bandpass filter are proposed. First, SIW bandpass filter is proposed using six rectangular open loop resonators while the second SIW bandpass filter used eight rectangular open loop resonators. The simulation results for two kinds of the recommended rectangular open loop resonators have insertion loss (S<sub>21</sub> parameter) below 2 dB and return loss (S<sub>11</sub> parameter) more than 10 dB. Fabrication of the recommended two kind filters was validated by Vector Network Analyzer. The measurement results for six rectangular open loop resonators have 1.32 dB for S<sub>21</sub> parameter at 2.29 GHz while the S<sub>11</sub> parameter more than 18 dB at 2.26 GHz – 2.32 GHz. While the measurement results has good agreement for eight rectangular open loop resonators. Its have S<sub>21</sub> below 2.2 dB at 2.41 – 2.47 GHz and S<sub>11</sub> 16.27 dB at 2.38 GHz and 11.5 dB at 2.47 GHz.

scholarly journals A Compact Dual-Mode Bandpass Filter with High Out-of-Band Suppression Using a Stub-Loaded Resonator Based on the GaAs IPD Process

Electronics ◽  
2020 ◽  
Vol 9 (5) ◽  
pp. 712 ◽  
Author(s):  
Wei Zhang ◽  
Zhao Yao ◽  
Jie Zhang ◽  
Eun Seong Kim ◽  
Nam Young Kim
Keyword(s):  
Insertion Loss ◽  
High Performance ◽  
Return Loss ◽  
Bandpass Filter ◽  
Open Loop ◽  
Fabrication Process ◽  
Dual Mode ◽  
Transmission Zeros ◽  
Semiconductor Fabrication ◽  
Device Size

In this letter, a compact dual-mode bandpass filter (BPF) with an ultra-wide stopband that employs two folded open-loop resonators (FOLRs) and stub-loaded resonators (SLRs) is proposed. The dual-mode resonators are optimized by loading two SLRs onto the folded open-loop resonators, and this process is analyzed using the dual-mode theory. To miniaturize the device size and increase chip performance, the proposed BPF is fabricated by a III–V compound semiconductor-fabrication process using a high-performance GaAs substrate based on the integration passivation device (IPD) fabrication process. A compact dual-mode BPF with low insertion loss and high return loss is designed and fabricated. Two extra transmission zeros (TZs) located in the high-frequency range increase the wide stopband, and the two TZs near the passband result in a higher selectivity. A resonant frequency centered at 7.45 GHz with an insertion loss of −1.21 dB and a measured return loss of higher than −23.53 dB and 3 dB fractional bandwidths of 5.8% are achieved. The stopband can be suppressed up to 20 GHz owing to the two tunable TZs resulting in higher selectivity and wideband rejection. The size of the filter was drastically optimized using a simplified architecture of two FOLRs and SLRs.

A wide stopband multilayer substrate integrated waveguide bandpass filter with suppression of higher-order mode coupling

2021 ◽  
pp. 1-8
Author(s):  
Cong Tang ◽  
Fei Cheng ◽  
Chao Gu
Keyword(s):  
Bandpass Filter ◽  
Single Layer ◽  
Magnetic Coupling ◽  
Higher Order ◽  
Center Frequency ◽  
Substrate Integrated Waveguide ◽  
Cavity Resonators ◽  
Resonant Modes ◽  
Compact Size ◽  
Multilayer Substrate

Abstract This paper presents a compact multilayer substrate integrated waveguide (SIW) bandpass filter with wide stopband. The square SIW cavity resonators in multilayer substrates are horizontally and vertically coupled with magnetic coupling. By properly designing the coupling structure, the couplings between the higher-order resonant modes can be suppressed. Compared with the conventional single-layer SIW filters, the proposed multilayer SIW filter also exhibits a compact size. To verify the design concept, a double-layered SIW filter is fabricated and measured. The measured results agree well with the simulations. The measured results show that the upper stopband of the filter is extended to 2.73 times of the center frequency 8.02 GHz.

Compact microstrip bandpass filter using dual closed-loop stepped impedance resonator

2018 ◽  
Vol 10 (4) ◽  
pp. 405-411 ◽  
Author(s):  
Salif N. Dembele ◽  
Ting Zhang ◽  
Jingfu Bao ◽  
Denis Bukuru
Keyword(s):  
Circuit Design ◽  
Return Loss ◽  
Closed Loop ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Fractional Bandwidth ◽  
Transmission Zeros ◽  
Measurement Results ◽  
Frequency Position ◽  
Stepped Impedance Resonator

AbstractA dual closed-loop stepped impedance resonator (DCLSIR) is investigated and used in designing a compact microstrip bandpass filter (BPF). The proposed DCLSIR is symmetrical; as a result, the symmetric characteristics of the resonator have been used. The design equations are derived and used to support the circuit design. The center frequency, position of transmission zeros, and fractional bandwidth (FBW) are easily tuned by changing the physical dimensions of the resonator. Three transmission zeros are generated to improve the performance in the upper stopband. A DCLSIR prototype BPF is fabricated with a center frequency of 9.3 GHz, and evaluated to validate the design concept. The measured FBW is 9.25%, the insertion loss is 1.58 dB, and the return loss is over 17 dB. The measurement results agree well with the simulation results.

scholarly journals Rancang Bangun Band Pass Filter Frekuensi 1.27 GHz untuk Teknologi Synthetic Aperture Radar

2018 ◽  
Vol 5 (2) ◽  
pp. 149
Author(s):  
RIFAN FITRIANTO ◽  
YUYUN SITI ROHMAH ◽  
EFA MAYDHONA SAPUTRA
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Measurement Results ◽  
Epoxy Material ◽  
It Support ◽  
Band Pass ◽  
Aperture Radar

ABSTRAKSynthetic Apertur Radar (SAR) adalah teknologi radar yang digunakan untuk pengambilan gambar suatu objek dalam bentuk 2 atau 3 dimensi (penginderaan jarak jauh). Sistem tersebut  bekerja pada rentang frekuensi 1.265 sampai dengan 1.275 GHZ dengan frekuensi tengahnya 1.27 GHz. Agar sistem SAR ini dapat bekerja dengan optimal, dibutuhkan suatu perangkat filter yang dapat meloloskan frekuensi yang diinginkan. Sebelumnya sudah ada penelitian yang membuat perangkat ini di band frekuensi yang sama namun menggunakan bahan duroid 5880 dan resonator berbentuk kotak. Bandpass filter Pada penelitian ini dirancang dengan menggunakan metode Hairpin line dan bahan epoxy FR4. Hasil pengukuran menunjukkan nilai Return Loss masih cukup besar yaitu -9.33 dB dan nilai Insertion Loss minimal sebesar -13.51 dB.Kata kunci: Syntethic Aperture Radar, Band Pass Filter, Hairpin-lineABSTRACTSynthetic Aperture Radar (SAR) is a radar technology that used for taking an object in the form of 2 or 3 dimensions (remote sensing). It works in the frequency range 1.265 to 1.275 GHZ with a middle frequency of 1.27 GHz. SAR system can work optimally if it support a filter device that can pass the desired frequency. Previously there has been research that makes this device in the same frequency band but using 5885 duroid material and square resonator. Bandpass filter In this study designed using Hairpin line method and FR4 epoxy material. The measurement results of Return Loss values are still quite large  arround -9.33 dB and Insertion Loss minimum at -13.51 dB.Keywords: Syntethic Aperture Radar, Band Pass Filter, Hairpin line

Computer-Aided Analysis and Measurement of an Interconnection System

2011 ◽  
Vol 308-310 ◽  
pp. 2279-2285
Author(s):  
Wei Chen Lee ◽  
Hill Wu
Keyword(s):  
Simulation Model ◽  
Frequency Domain ◽  
Insertion Loss ◽  
Return Loss ◽  
Design Phase ◽  
Electrical Characteristics ◽  
Impedance Mismatch ◽  
Measurement Results ◽  
Computer Aided Analysis ◽  
Computer Aided

The electrical characteristics of an interconnection system, which include impedance, insertion loss, and return loss, can greatly affect its performance as the signal speed increases. The objective of this research was to understand the discrepancy between the computer-aided analysis and measurement results of an interconnection system, so that a more accurate prediction of the electrical characteristics of this system can be made during the design phase. It was discovered that in both the time and frequency domain the computer-aided analysis results were consistent with the measurement results. Given these conclusions the simulation model was modified to improve the impedance mismatch within the interconnection system. It was found that by properly designing the antipad, the impedance mismatch can be greatly reduced.

scholarly journals Sharp Skirt Dual-Mode Bandpass Filter with Overlay Plate to Control Upper Passband Edge

2019 ◽  
Vol 8 (6) ◽  
pp. 2357-2360
Keyword(s):  
Analytical Model ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Dual Mode ◽  
Rf Receivers ◽  
Attenuation Level ◽  
Frequency Selective ◽  
Fixed Center

This paper presents design and analytical model for Sharp Skirt Dual-Mode Bandpass Filter for RF receivers. Proposed filter is designed using open stub loaded H shaped resonator. Based on analytical model insertion loss S21 and return loss S11 for proposed filter are demonstrated. Inductive Overlaying plate is proposed to control upper passband edge of proposed filter to improve frequency selectivity with fixed center frequency. The proposed filter has sharp frequency selective range from 5.1GHz to 9.2GHz. With overlay plate, frequency selective range is tuned to 5.1GHz-8.6GHz. Without overlaying plate the proposed filter has return loss greater than 10dB and insertion loss of 0.7dB. Lower and upper passband edges are at 5.1GHz and 9.2GHz with attenuation level of 52dB and 54dB respectively. With overlaying plate, the filter has same S 11 and S 21 parameters, but upper passband edge is shifted from 9.2GHz to 8.6GHz

scholarly journals Design and Realization of Band Pass Filter in K-Band Frequency for Short Range Radar Application

2021 ◽  
Vol 21 (1) ◽  
pp. 1
Author(s):  
Arie Setiawan ◽  
Taufiqqurrachman Taufiqqurrachman ◽  
Adam Kusumah Firdaus ◽  
Fajri Darwis ◽  
Aminuddin Rizal ◽  
...  
Keyword(s):  
Insertion Loss ◽  
Short Range ◽  
Return Loss ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Frequency ◽  
Measurement Results ◽  
Band Pass ◽  
Bandwidth Analysis ◽  
K Band

Short range radar (SRR) uses the K-band frequency range in its application. The radar requires high-resolution, so the applied frequency is 1 GHz wide. The filter is one of the devices used to ensure only a predetermined frequency is received by the radar system. This device must have a wide operating bandwidth to meet the specification of the radar. In this paper, a band pass filter (BPF) is proposed. It is designed and fabricated on RO4003C substrate using the substrate integrated waveguide (SIW) technique, results in a wide bandwidth at the K-band frequency that centered at 24 GHz. Besides the bandwidth analysis, the analysis of the insertion loss, the return loss, and the dimension are also reported. The simulated results of the bandpass filter are: VSWR of 1.0308, a return loss of -36.9344 dB, and an insertion loss of -0.6695 dB. The measurement results show that the design obtains a VSWR of 2.067, a return loss of -8.136 dB, and an insertion loss of -4.316  dB. While, it is obtained that the bandwidth is reduced by about 50% compared with the simulation. The result differences between simulation and measurement are mainly due to the imperfect fabrication process.

Sign in / Sign up

Export Citation Format

Share Document