Photoelectrocatalytic Degradation of HCB by N-Doped TiO2 Nanotube Arrays

2013 ◽  
Vol 652-654 ◽  
pp. 1580-1584
Author(s):  
Yu Jiang Guan ◽  
Zi Bo Wang ◽  
Shu Li Bai ◽  
Qin Xue
Keyword(s):  
Photoelectron Spectroscopy ◽  
Ph Value ◽  
Nanotube Arrays ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Photoelectrocatalytic Degradation ◽  
Doping Behavior ◽  
Doped Titanium Dioxide ◽  
Scanning Electron

N-doped Titanium dioxide (TiO2) nanotube arrays were characterized by scanning electron microscope (SEM)，X-ray Diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) to analyse its surface morphology, crystal types and the doping behavior of nitrogen. The material was used as electrode for photoelectrocatalytic degradation of hexachlorobenzen under irradiation of simulated sunlight. The effects of photocatalysis, electrocatalysis, photoelectrocatalysis, the concentration of Na2SO4 and pH value on degradation of HCB were investigated.

scholarly journals Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 558
Author(s):  
Wenhui Zhu ◽  
Caiyun Zhang ◽  
Yali Chen ◽  
Qiliang Deng
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Degradation Rate ◽  
Model Compound ◽  
Vibrating Sample Magnetometer ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Preparation of Borosilicate Xerogel and Research on its Mineralization

2012 ◽  
Vol 476-478 ◽  
pp. 2059-2062
Author(s):  
Chen Wang ◽  
Ya Dong Li ◽  
Gu Qiao Ding
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Ph Value ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compositional Changes ◽  
Scanning Electron

Tributyl borate was first adopted for the introduction of boron in the preparation of bioactive borosilicate xerogel by sol-gel method. The xerogel reacted continuously in 0.25M K2HPO4 solution with a starting pH value of 7.0 at 37 °C for 1day. The structural, morphologies and compositional changes resulting from the conversion were characterized using X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The results indicated that speed of formation of HA was cut way back on the time with the addition of boron and the induction period for the HA nucleation on the surface of the borosilicate xerogel was short than 1 days. The conversion mechanism of the borosilicate xerogels to hydroxyapaptite was also discussed.

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

scholarly journals Reduced Graphene Oxide–Epoxy Grafted Poly(Styrene-Co-Acrylate) Composites for Corrosion Protection of Mild Steel

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 666
Author(s):  
Xinchuan Fan ◽  
Yue Hu ◽  
Yijun Zhang ◽  
Jiachen Lu ◽  
Xiaofeng Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Corrosion Properties ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Scanning Electron

Reduced graphene oxide–epoxy grafted poly(styrene-co-acrylate) composites (GESA) were prepared by anchoring different amount of epoxy modified poly(styrene-co-acrylate) (EPSA) onto reduced graphene oxide (rGO) sheets through π–π electrostatic attraction. The GESA composites were characterized by Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The anti-corrosion properties of rGO/EPSA composites were evaluated by electro-chemical impedance spectroscopy (EIS) in hydroxyl-polyacrylate coating, and the results revealed that the corrosion rate was decreased from 3.509 × 10−1 to 1.394 × 10−6 mm/a.

Effect of Cu Content on the Tribological Performance of Cr-N Coatings at High Temperatures (840°C)

2009 ◽  
Author(s):  
Kyriaki Polychronopoulou ◽  
Claus Rebholz ◽  
Nicholaos G. Demas ◽  
Andreas A. Polycarpou ◽  
P. N. Gibson
Keyword(s):  
Vapor Deposition ◽  
Photoelectron Spectroscopy ◽  
Physical Vapor Deposition ◽  
Tribological Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cu Content ◽  
Glancing Angle ◽  
Scanning Electron ◽  
Ball On Disc

Cr-N and Cu-Cr-N coatings with Cu content between 3–65 at.%, Cu/Cr ratios in the 0.04–4.5 range and 21–27 at.% N, synthesized by twin e-beam Physical Vapor Deposition (EBPVD) at 450°C, were investigated. Using X-ray photoelectron spectroscopy (XPS), glancing angle X-ray diffraction (GAXRD) and scanning electron microscopy (SEM), in combination with nanoindentation mechanical property measurements and laboratory controlled ball-on-disc sliding experiments, it is shown that Cu-Cr-N coatings with low Cu content (3 at.%) possess sufficient wear resistance for high temperature demanding tribological applications.

scholarly journals Preparation of Cerium Dioxide Layers on Titanium by Electrodeposition with Organic Solution

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Vaijayanti Namdeo Nande ◽  
Diana Kostyukova ◽  
Jeonghee Choi ◽  
Yong Hee Chung
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Cerium Dioxide ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
Organic Solution ◽  
X Ray ◽  
Titanium Foils ◽  
Scanning Electron

Layers of cerium dioxide nanoparticles were prepared on titanium by electrodeposition with organic solution. Three concentrations of cerium ions were used at 31.6 V. The organic solution was isobutanol and titanium foils were used as anodes and cathodes. Currents were monitored during the electrodeposition. Deposition times ranged from 0.5 to 8 h. Deposited Deposited layers were calcined at 700 K for 30 min. The morphology and composition of the deposited layers were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). As-prepared and calcined deposition layers were assayed to be cerium dioxide. The average crystallite size increased from 4 to 7 nm through calcination at 700 K. Sizes of calcined cerium oxide agglomerates were ranging from 73 to 146 nm for 30 min deposition and 209 to 262 nm for 8 h deposition. The electrodeposition efficiencies of 0.5 h deposition at three concentrations were measured to be highest.

Influence of pH on the Morphology and Luminescence Properties of Europium-Doped Hydroxyapatite Nanoparticles

2011 ◽  
Vol 391-392 ◽  
pp. 1132-1137
Author(s):  
Su Ping Huang ◽  
Jun Zhu ◽  
Ke Chao Zhou
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Doping Concentration ◽  
Ph Value ◽  
Luminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Ph Values ◽  
Influence Of Ph

Luminescence behaviors and morphology of Eu3+doped hydroxyapatite synthesized under different pH values were well investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Inductively Coupled Plasma (ICP) (ICP–PLASMA 1000), and photoluminescence (PL) spectroscopy. Results revealed that With pH values increased from 6.5 to 10.0, the morphology of nano-Eu:HA particles changes from rod particles to equiaxed particles. The actual doping concentration and aspect ratio of Eu3+-doped HA decreased with the increasing of pH value. At the same time, the fluorescence intensity also tends to weakly lower with the increasing of pH value, which indicated that the luminescence properties mainly depended on the actual Eu3+doping concentration, the influences of morphology on the luminescence properties were slight.

Preparation and Characterization of N Doped TiO2/ Sepiolite Composite Materials

2011 ◽  
Vol 284-286 ◽  
pp. 597-600
Author(s):  
Dai Mei Chen ◽  
Hai Peng Ji ◽  
Jian Xin Wang ◽  
Jian Chen ◽  
Xin Long Luan ◽  
...  
Keyword(s):  
Composite Materials ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nitrogen Doped ◽  
Nitrogen Contents ◽  
Scanning Electron ◽  
Oxygen Atoms

Nitrogen doped TiO2/sepiolite composite materials (N-TiO2/sep) with different nitrogen contents were prepared by a sol-gel method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), respectively. XRD and SEM results showed that anatase-TiO2nanoparticles were distributed homogenously on the surface of sepiolite. XPS revealed that N atoms could incorporate into the lattice of anatase TiO2substituting the oxygen atoms sites of oxygen atoms.

Photocatalysis Reactivity in the Visible Light of B-Doped TiO2 Nanotube Arrays

2013 ◽  
Vol 860-863 ◽  
pp. 907-910
Author(s):  
Xiao Xia Lin ◽  
Jia Liu ◽  
De Gang Fu
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectrum ◽  
Nanotube Arrays ◽  
X Ray Diffraction ◽  
Degradation Model ◽  
X Ray ◽  
Light Region

B-doped TiO2nanotube arrays (B-TNTs) were synthesized by anodization method combined with dip-calcination technique. The physicochemical properties and surface morphology were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and UV-Vis diffuse reflectance spectrum (DRS). Methyl blue (MB) solution was utilized as the degradation model to evaluate the photocatalytic activity of B-TNTs under visible light irradiation. The results show B-TNTs shifts the absorption edge of TiO2nanotube arrays to the visible light region and B-TNTs displays higher photocatalytic activity compared with undoped TNTs.

Sign in / Sign up

Export Citation Format

Share Document