Characterization of the Surface Quality of Holes Drilled in CFRP Laminates

2013 ◽  
Vol 698 ◽  
pp. 107-116 ◽  
Author(s):  
Yann Landon ◽  
Mehdi Cherif
Keyword(s):  
Tool Wear ◽  
Surface Quality ◽  
Composite Structures ◽  
Angular Position ◽  
Cutting Parameters ◽  
Experimental Phase ◽  
Cfrp Laminates ◽  
The Impact

Assembling composite structures requires a significant number of drillings. During machining, defects appear on the surface of the drilled hole. This paper outlines that the criterion Ra is not adapted to reliably characterize the surface quality on composites. In particular, various tests have shown significant variations of the value of Ra according to the angular position of measurement, as well as the filtering artefacts. This study puts forward a new methodology to characterize the surface quality of a composite hole. To this end, a study of sensitivity of the various criteria proposed by standard ISO4287 was conducted. Various geometries of tool are also tested in the experimental phase. The impact of cutting parameters and tool wear are analyzed based on this new methodology.

Comparative Study of Material Damage and Tool Wear Mechanisms During Drilling of CFRP/Ti Stack

2019 ◽  
Author(s):  
Vijayathithan Mathiyazhagan ◽  
Anil Meena
Keyword(s):  
Tool Wear ◽  
Surface Quality ◽  
Cutting Parameters ◽  
Burr Formation ◽  
Mechanical And Thermal Properties ◽  
Hole Quality ◽  
Structural Functions ◽  
Tool Wear Mechanisms ◽  
Rapid Tool

Abstract The usage of CFRP and Ti stacks in the aerospace industry has widely increased due to its mechanical properties and improved structural functions but at the same time, different mechanical and thermal properties of the CFRP and Ti makes the process difficult. Major apprehensions in the drilling of CFRP/Ti stacks include rapid tool wear and poor hole quality. Typically, the surface quality of the holes in the drilling of CFRP/Ti stack is poor due to delamination, the progression of hole diameter in CFRP and burr formation in Ti. Moreover, the flank wear on the tool also influences the surface quality of the hole produced. Therefore, the present study is mainly focused on the influence of cutting parameters on cutting forces, hole quality and tool wear characteristics. Drilling was performed on CFRP/Ti stack using coated and uncoated carbide tools. The obtained results revealed a significant correlation between tool wear and delamination characteristics.

Influence of Cutting Conditions on Surface and Sub-Surface Quality of High Speed Dry End Milling Ti-6Al-4V

2014 ◽  
Vol 67 (3) ◽  
Author(s):  
H. Safari ◽  
S. Izman
Keyword(s):  
Plastic Deformation ◽  
Tool Wear ◽  
Surface Quality ◽  
High Speed ◽  
End Milling ◽  
Cutting Parameters ◽  
Machining Process ◽  
Surface Alteration ◽  
Cutting Speeds

Surface quality is one of the most critical restraints for determining cutting parameters and selecting of machining process in metal cutting process. In this study, the effects of cutting parameters and tool wear on the surface and sub-surface quality of high speed dry end milling Ti-6Al-4V were investigated. PVD Coated carbide tools were used under different high cutting speeds and feed rates. The quality of the machined surface and corresponding alteration on the sub-surface and entry/exit edges were characterized through scanning electron microscopy. The results showed that the better surface quality was obtained when machining at higher cutting speeds and feed rates. High speed dry end milling using the worn tool causes to plastic deformation of the alloy which is resulted in developing the lamellae on the surface and causing poor surface finish. Worn tools with the uniform tool wear land generated better surface quality compare to those with chipping and flaking on the tool edge surface. Tool wear is suggested as the other contributing factor in developing entry and exit edge damages. The results of sub-surface alteration measurement revealed that the worn tool enhanced the sub-surface alteration resulted in 45% increase in plastic deformation compare to the new tool.

Research Status of Subsequent Machining of Laser Cladding Layers

2020 ◽  
Vol 15 ◽  
Author(s):  
Lei Li ◽  
Yujun Cai ◽  
Guohe Li ◽  
Meng Liu
Keyword(s):  
Tool Wear ◽  
Surface Quality ◽  
Laser Cladding ◽  
Wear Surface ◽  
Chip Formation ◽  
Cutting Temperature ◽  
Dimensional Accuracy ◽  
Cutting Parameters ◽  
Cladding Layer ◽  
Cladding Layers

Background: As an important method of remanufacturing, laser cladding can be used to obtain the parts with specific shapes by stacking materials layer by layer. The formation mechanism of laser cladding determines the “Staircase effect”, which makes the surface quality can hardly meet the dimensional accuracy of the parts. Therefore, the subsequent machining must be performed to improve the dimensional accuracy and surface quality of cladding parts. Methods: In this paper, chip formation, cutting force, cutting temperature, tool wear, surface quality, and optimization of cutting parameters in the subsequent cutting of laser cladding layer are analyzed. Scholars have expounded and studied these five aspects but the cutting mechanism of laser cladding need further research. Results: The characteristics of cladding layer are similar to that of difficult to machine materials, and the change of parameters has a significant impact on the cutting performance. Conclusion: The research status of subsequent machining of cladding layers is summarized, mainly from the aspects of chip formation, cutting force, cutting temperature, tool wear, surface quality, and cutting parameters optimization. Besides, the existing problems and further developments of subsequent machining of cladding layers are pointed out. The efforts are helpful to promote the development and application of laser cladding remanufacturing technology.

scholarly journals Analysis of the surface quality of polycaprolactam 3D prints enriched with carbon and glass fiber

2021 ◽  
Vol 338 ◽  
pp. 01005
Author(s):  
Damian Dzienniak ◽  
Jan Pawlik
Keyword(s):  
Glass Fiber ◽  
Surface Quality ◽  
Fused Deposition Modeling ◽  
Polyamide 6 ◽  
Fiber Glass ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact ◽  
The Relationship

Additive manufacturing has been gaining popularity and availability year by year, which has resulted in its dynamic development. The most common 3D printing method as of today, FDM (Fused Deposition Modeling), owing to its peculiarity, does not always guarantee producing objects with low surface roughness. The authors of the present article have taken on the analysis of the impact of FDM printing on the roughness of the filament thus processed. They also investigate the relationship between the roughness of the unprocessed filament (made of polycaprolactam, that is, polyamide 6 or PA6) with admixtures of other materials (carbon fiber, glass fiber) and the surface quality of the manufactured object. The main subject of the analysis is the side surfaces of 3D prints, as it is their quality that is usually directly dependent on many factors connected with the process of the laying of the consecutive layers. The authors check step by step whether there exists a pronounced relationship between the roughness of the original filament material and the roughness of the obtained surface.

scholarly journals Energy and Exergy Analyses of Stirling Engine using CFD Approach

2020 ◽  
Vol 77 (1) ◽  
pp. 100-123
Author(s):  
Sherihan El- Ghafour ◽  
Nady Mikhael ◽  
Mohamed El- Ghandour
Keyword(s):  
Energy Analysis ◽  
Stirling Engine ◽  
Recovery Processes ◽  
Energy And Exergy ◽  
Main Driver ◽  
The Impact ◽  
Exergy Analyses ◽  
Comprehensive Characterization

A comprehensive characterization of the GPU-3 Stirling engine losses with the aid of the CFD approach is presented. Firstly, a detailed description of the losses-related phenomena along with the method of calculating each type of loss are addressed. Secondly, an energy analysis of the engine is carried out in order to specify the impact of each type of losses on the performance. Finally, the design effectivity of each component of the engine is investigated using an exergy analysis. The results reveal that the hysteresis loss occurs mainly within the working spaces due to the flow jetting during the first part of the expansion strokes. Additionally, the pressure difference between the working spaces is the main driver for the flow leakage through the appendix gap. The exposure of the displacer top wall to the jet of hot gas flowing into the expansion space during expansion stroke essentially increases the shuttle heat loss. A new definition for the regenerator effectiveness is presented to assess the quality of the heat storage and recovery processes. The energy analysis shows that regenerator thermal loss and pumping power represent the largest part of the engine losses by about 9.2% and 7.5% of the heat input, respectively. The exergy losses within regenerator and cold space are the highest values among the components, consequently, they need to be redesigned.

Surface Quality of Pulsed Laser Cutting of Difficult to Machine Steel

2011 ◽  
Vol 299-300 ◽  
pp. 1016-1019
Author(s):  
Tie Jun Li ◽  
Jing Tang ◽  
Li Jun Yan ◽  
Yang Wang
Keyword(s):  
Surface Quality ◽  
Laser Cutting ◽  
Pulsed Laser ◽  
Cutting Parameters ◽  
Quality Factors ◽  
Good Separation ◽  
Machine Steel ◽  
Optimum Cutting ◽  
Super Alloy

This paper presented the experiments of Nd:YAG pulsed laser cutting of titanium alloy, super-alloy and stainless steel sheet, and investigated the influences of different laser cutting parameters on the surface quality factors focusing surface morphology. In comparison with air-, argon- and nitrogen-assisted laser cutting, argon-assisted laser cutting comes with unaffected surface quality and is suitable for laser cutting with subsequent welding requirement. With analyzing the interaction between pulses overlapping rate and energy, the results show that medium pulse overlapping rate and lower pulse rate helps to improve the surface roughness with pulsed laser cutting. And the results would be beneficial to find optimum cutting parameters for good separation surface.

Dynamic-SoS: An Approach for the Simulation of Systems-of-Systems Dynamic Architectures

2019 ◽  
Vol 63 (5) ◽  
pp. 709-731
Author(s):  
Wallace Manzano ◽  
Valdemar Vicente Graciano Neto ◽  
Elisa Yumi Nakagawa
Keyword(s):  
Architectural Design ◽  
Systems Of Systems ◽  
Dynamic Architecture ◽  
Design Time ◽  
Operation Results ◽  
The Impact ◽  
Reconfiguration Controller

Abstract Systems-of-Systems (SoS) combine heterogeneous, independent systems to offer complex functionalities for highly dynamic smart applications. Besides their dynamic architecture with continuous changes at runtime, SoS should be reliable and work without interrupting their operation and with no failures that could cause accidents or losses. SoS architectural design should facilitate the prediction of the impact of architectural changes and potential failures due to SoS behavior. However, existing approaches do not support such evaluation. Hence, these systems have been usually built without a proper evaluation of their architecture. This article presents Dynamic-SoS, an approach to predict/anticipate at design time the SoS architectural behavior at runtime to evaluate whether the SoS can sustain their operation. The main contributions of this approach comprise: (i) characterization of the dynamic architecture changes via a set of well-defined operators; (ii) a strategy to automatically include a reconfiguration controller for SoS simulation; and (iii) a means to evaluate architectural configurations that an SoS could assume at runtime, assessing their impact on the viability of the SoS operation. Results of our case study reveal Dynamic-SoS is a promising approach that could contribute to the quality of SoS by enabling prior assessment of its dynamic architecture.

scholarly journals Impact of Structural Defects on the Surface Quality of Hardwood Species Sliced Veneers

2020 ◽  
Vol 10 (18) ◽  
pp. 6265
Author(s):  
Vasiliki Kamperidou ◽  
Efstratios Aidinidis ◽  
Ioannis Barboutis
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Wood Species ◽  
Research Work ◽  
Structural Defects ◽  
Material Surface ◽  
Typical Structure ◽  
Hardwood Species ◽  
The Impact

The surface roughness constitutes one of the most critical properties of wood and wood veneers for their extended utilization, affecting the bonding ability of the veneers with one another in the manufacturing of wood composites, the finishing, coating and preservation processes, and the appearance and texture of the material surface. In this research work, logs of five significant European hardwood species (oak, chestnut, ash, poplar, cherry) of Balkan origin were sliced into decorative veneers. Their surface roughness was examined by applying a stylus tracing method, on typical wood structure areas of each wood species, as well as around the areas of wood defects (knots, decay, annual rings irregularities, etc.), to compare them and assess the impact of the defects on the surface quality of veneers. The chestnut veneers presented the smoothest surfaces, while ash veneers, despite the higher density, recorded the highest roughness. In most of the cases, the roughness was found to be significantly lower around the defects, compared to the typical structure surfaces, probably due to lower porosity, higher density and the presence of tensile wood. The results reveal that the presence of defects does not affect the roughness of the veneers and increases neither the processing requirements of the veneer sheets before finishing, nor the respective production cost of veneers and the veneer-based wood panels. The high utilization prospects of the examined wood species in veneer production, even those bearing various defects, is highlighted.

scholarly journals Surface Roughness Investigation of Poly-Jet 3D Printing

Mathematics ◽  
2020 ◽  
Vol 8 (10) ◽  
pp. 1758
Author(s):  
Nectarios Vidakis ◽  
Markos Petousis ◽  
Nikolaos Vaxevanidis ◽  
John Kechagias
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Surface Quality ◽  
Back Propagation ◽  
Physical Models ◽  
Layer By Layer ◽  
Linear Regression Models ◽  
Feed Forward Back Propagation ◽  
The Impact

An experimental investigation of the surface quality of the Poly-Jet 3D printing (PJ-3DP) process is presented. PJ-3DP is an additive manufacturing process, which uses jetted photopolymer droplets, which are immediately cured with ultraviolet lamps, to build physical models, layer-by-layer. This method is fast and accurate due to the mechanism it uses for the deposition of layers as well as the 16 microns of layer thickness used. Τo characterize the surface quality of PJ-3DP printed parts, an experiment was designed and the results were analyzed to identify the impact of the deposition angle and blade mechanism motion onto the surface roughness. First, linear regression models were extracted for the prediction of surface quality parameters, such as the average surface roughness (Ra) and the total height of the profile (Rt) in the X and Y directions. Then, a Feed Forward Back Propagation Neural Network (FFBP-NN) was proposed for increasing the prediction performance of the surface roughness parameters Ra and Rt. These two models were compared with the reported ones in the literature; it was revealed that both performed better, leading to more accurate surface roughness predictions, whilst the NN model resulted in the best predictions, in particular for the Ra parameter.

Analysis of the Assembly Joint at Deformation of Matched Objects

2019 ◽  
Vol 952 ◽  
pp. 330-338
Author(s):  
Marcela Bučányová ◽  
Miriam Matúšová ◽  
Erika Hrušková
Keyword(s):  
Surface Quality ◽  
Specific Activity ◽  
Technological Equipment ◽  
Time Performance ◽  
Final Surface ◽  
The Impact ◽  
Material Tool

Maintenance is a system-specific activity that the purpose of which is to maintain or to increase time, performance and quality of machines and equipment use. The demand for technological equipment is still rising, resulting in often complicated and lengthy repairs. It is necessary to analyze the tools used in the construction of assembly joints and to describe the deficiencies that may occur during assembly. When contacting a material tool using a particular technology and assembly, it is necessary to analyze the impact on the final surface quality of the material.

Sign in / Sign up

Export Citation Format

Share Document