Study on the Preparation of Strontium-Doped Hydroxyapatite Whisker

2013 ◽  
Vol 738 ◽  
pp. 26-29 ◽  
Author(s):  
Ting Ting Yan ◽  
Yong Shun Cui ◽  
Qing Hua Chen
Keyword(s):  
Mechanical Property ◽  
Bone Repair ◽  
Calcium Nitrate ◽  
Xrd Analysis ◽  
Strontium Nitrate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Repair Materials ◽  
Bone Repair Materials ◽  
Scanning Electron

Hydroxyapatite is well used as bone repair materials, due to its properties that can be combined with strontium to improve mechanical property and degradation property. In this article, hydroxyapatite whiskers with different amount of doped strontium were prepared with diammonium phosphate, calcium nitrate and strontium nitrate at 94 °C. Fourier transform infrared spectroscopy (FTIR) was used to identify the functional groups. X-ray diffraction (XRD) analysis was carried out to study the phase composition and crystallinity of the whisker. The morphology of the whiskers was characterized by scanning electron microscope (SEM). It was indicated that strontium can be doped in hydroxyapatite with proper process and then the strontium-doped hydroxyapatite whiskers were produced successfully.

scholarly journals Solvothermally derived Me2(H2O)4(5SSA)3·DMF and Me2(H2O)4(4NSA)2·DMF: Application as Biginelli reaction catalysts

Chemija ◽  
2019 ◽  
Vol 30 (2) ◽  
Author(s):  
Andrius Laurikėnas ◽  
Fatma Yalçin ◽  
Robertas Žilinskas ◽  
Ayse Uztetik Morkan ◽  
Albinas Žilinskas ◽  
...  
Keyword(s):  
Solvothermal Synthesis ◽  
Catalytic Properties ◽  
Inorganic Compounds ◽  
Biginelli Reaction ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hybrid Compounds ◽  
Phase And Chemical Composition ◽  
Scanning Electron

The solvothermal synthesis between Me(NO3)x ∙ yH2O (Mex+ = Fe3+, Ni2+, Mn2+, Co2+, Cu2+) and respectively 4-nitrosalycilic (4NSA) and 5-sulfosalicylic (5SSA) acids produced hybrid organic-inorganic compounds composed of Mex+ ions and organic fragments which include three different functional groups, carboxylic, hydroxyl and sulfonic, each coordinated to the Mex+ ions. The phase and chemical composition, microstructure and properties of Me2(H2O)4(5SSA)3·DMF and Me2(H2O)4(4NSA)2·DMF (DMF – dimethylformamide) hybrid compounds were evaluated and discussed. The synthesised materials were characterised by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) spectroscopy. The catalytic properties of the obtained compounds were also investigated.

scholarly journals Photocatalytic Degradation of Nitro and Chlorophenols Using Doped and Undoped Titanium Dioxide Nanoparticles

2011 ◽  
Vol 2011 ◽  
pp. 1-8 ◽  
Author(s):  
Hassan Ilyas ◽  
Ishtiaq A. Qazi ◽  
Wasim Asgar ◽  
M. Ali Awan ◽  
Zahir-ud-din Khan
Keyword(s):  
Photocatalytic Degradation ◽  
Crystallite Size ◽  
Model Compound ◽  
Titanium Dioxide Nanoparticles ◽  
Xrd Analysis ◽  
Scanning Electron Micrographs ◽  
X Ray Diffraction ◽  
X Ray ◽  
Liquid Impregnation ◽  
Scanning Electron

Pure and Ag-TiO2nanoparticles were synthesized, with the metallic doping being done using the Liquid Impregnation (LI) method. The resulting nanoparticles were characterized by analytical methods such as scanning electron micrographs (SEMs), Energy Dispersive Spectroscopy (EDS), and X-ray diffraction (XRD). XRD analysis indicated that the crystallite size ofTiO2was 27 nm to 42 nm while the crystallite size of Ag-TiO2was 11.27 nm to 42.52 nm. The photocatalytic activity of pureTiO2and silver dopedTiO2was tested by photocatalytic degradation ofp-nitrophenol as a model compound. Ag-TiO2nanoparticles exhibited better results (98% degradation) as compared to pureTiO2nanoparticles (83% degradation) in 1 hour for the degradation ofp-nitrophenol. Ag-TiO2was further used for the photocatalytic degradation of 2,4-dichlorphenol (99% degradation), 2,5-dichlorophenol (98% degradation), and 2,4,6-trichlorophenol (96% degradation) in 1 hour. The degree of mineralization was tested by TOC experiment indicating that 2,4-DCP was completely mineralized, while 2,5-DCP was mineralized upto 95 percent and 2,4,6-TCP upto 86 percent within a period of 2 hours.

The Influence of Mn Doping on the Dielectric Properties of Ba0.5Sr0.5TiO3 Ceramics

2016 ◽  
Vol 859 ◽  
pp. 18-23 ◽  
Author(s):  
Li Ping Zhao ◽  
Wen Hong Tao ◽  
Xing Hua Fu ◽  
Wen Zhe Cao ◽  
Guo Yuan Cheng ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Material Properties ◽  
Room Temperature ◽  
Sol Gel ◽  
Barium Nitrate ◽  
Strontium Nitrate ◽  
X Ray Diffraction ◽  
Mn Doping ◽  
X Ray ◽  
Scanning Electron

(Ba0.5Sr0.5)1-xMnxTiO3(x=0,0.01,0.03,0.05)ceramics were prepared via a new sol-gel method with titannium oxide, strontium nitrate, barium nitrate and manganous nitrate as raw materials.The effect of Mn doping on the microstructure and dielectric properties of the BST were characterized by field scanning electron microscopy,x-ray diffraction and impedance analyser.It was found that the dopted ions could not alter the basic crystal strcuture and they only improved the material properties as modified ions when x≤0.3.The (Ba0.5Sr0.5)1-xMnxTiO3 ceramics sintered at 1250°C for 2h exhibited good dielectric properties(er=1330,tand=0.03)at room temperature and f=1KHz when x=0.03 and the grains were regular and uniform ,indicating a dense microstrcture.

Synthesis, Structural Analysis of Cadmium Sulphide Nanocrystallites

2019 ◽  
Vol 969 ◽  
pp. 169-174
Author(s):  
R. Sivanand ◽  
S. Chellammal ◽  
S. Manivannan
Keyword(s):  
Size Variation ◽  
Cadmium Sulphide ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Precipitation Method ◽  
Capping Agent ◽  
Energy Dispersive Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

In this paper, the effect of size variation of cadmium sulphide nanocrystallites which have been prepared by precipitation method is analyzed. These prepared samples were studied using X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive analysis of spectroscopy (EDAX) techniques. SEM analysis represents the morphological nature of prepared samples and EDAX indicates the confirmation of elements present in the sample. XRD analysis determines the size of the samples and identifies the structure using miller indices (h k l values) of the nanocrystallies matches with JCPDS. From the XRD analysis, the size variation which depends on dopant, capping agent are discussed and corresponding results are reported in this paper.

Microstructural Characterization of Glass-to-Metal Brazed Joint

2012 ◽  
Vol 616-618 ◽  
pp. 1732-1735 ◽  
Author(s):  
Xi Hai Shen ◽  
Yu Gang Zheng ◽  
Liang Chang ◽  
Jin Jia Guo ◽  
Song Bin Ye ◽  
...  
Keyword(s):  
Thermal Power ◽  
Microstructural Characterization ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solar Thermal Power ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Scanning Electron

Aiming at the glass-to-metal seals serving in the Solar Thermal Power (STP), glass-to-metal vacuum brazed joints were studied. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis were performed to examine the microstructure and element contents of interface seam on the glass-to-metal vacuum brazed joints. Also, the compositional concentration of the interface seam was measured by using energy dispersive spectroscopy (EDS).

The Effect of Water Content on the Formation of TiO2 Nanotubes in Ethylene Glycol

2010 ◽  
Vol 173 ◽  
pp. 102-105 ◽  
Author(s):  
Khairul Arifah Saharudin ◽  
Srimala Sreekantan
Keyword(s):  
Crystal Structure ◽  
Aspect Ratio ◽  
Ethylene Glycol ◽  
Water Content ◽  
Anatase Phase ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Degradation Of Methyl Orange ◽  
Scanning Electron

In this paper, anodization of Ti foil was carried out in ethylene glycol (EG) containing 5 wt% NH4F solution and 0 to 1.5 wt% of water at 50 V for 60 min. The pH of the bath was kept constant at ~pH7. The crystal structure was studied by X-Ray Diffraction (XRD) analysis, and the morphology was observed via field emission scanning electron microscopy (FESEM). TiO2 nanotube with aspect ratio of 100 was obtained in EG containing less than 1wt % water. The nanotubes wall was very smooth. Increasing the water content > 1wt % results in short nanotubes of approximately 6.2μm with aspect ratio of 62. As anodized, nanotubes were amorphous and annealed at 400 °C promote 100 % anatase phase. Photocatalytic activity of the nanotubes produced at different water content was also evaluated by the degradation of methyl orange and the detail of the observation was discussed thoroughly in this paper.

Study on Microstructure and Property of Diffusion-Bonded Mo-Cu Joints

2012 ◽  
Vol 508 ◽  
pp. 178-182
Author(s):  
Jian Zhang ◽  
Guo Qiang Luo ◽  
Mei Juan Li ◽  
Qiang Shen ◽  
Lian Meng Zhang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Property ◽  
Tensile Strength ◽  
Electron Probe ◽  
Bonding Process ◽  
Interfacial Structure ◽  
X Ray Diffraction ◽  
Strength Measurement ◽  
X Ray ◽  
Scanning Electron

Mo and Cu Were Bonded Successfully by Means of Vacuum Diffusion Bonding. The Interfacial Structure of the Joints Was Studied by Scanning Electron Microscopy (SEM), Electron Probe Microanalysis (EPMA), Energy Dispersive X-Ray Spectrometer (EDS) and X-Ray Diffraction (XRD), the Mechanical Property Is Tested by Tensile Strength Measurement. The Results Showed that the Differentatoms Diffused to each other in the Bonding Process. A Mo-Cu Solid Solution Was Formed in the Joint and with No Intermetallic Compounds. The Tensile Strength of the Joint Increased with the Increasing of Temperature, however, while the Holding Time Increased, the Strength Increased in the First Stages and then Decreases. It Were Observed that the Fracture Mode of the Joints Was a Brittle Fracture.

Interaction between Yttria Fully Stabilized Zirconia or Yttria-Zirconia Blended Face-Coat with Ti6Al4V during Investment Casting

2014 ◽  
Vol 1019 ◽  
pp. 302-310 ◽  
Author(s):  
Kalenda Mutombo ◽  
Christina Kgomo ◽  
P. Rossouw
Keyword(s):  
Electron Microscopy ◽  
Xrd Analysis ◽  
Experimental Results ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Hardness Tester ◽  
Alpha Case ◽  
Face Coat ◽  
Scanning Electron

The interaction between the Ti6Al4V alloy and the mould materials was investigated. The alpha-case was characterized by Vickers hardness tester, optical and scanning electron microscopy equipped with electron dispersive X-ray spectrometry (EDX). X-ray diffraction (XRD) analysis was performed on as cast and on YFSZ or YZ-Blended face-coats. From the experimental results, a distinct alpha-case formation was revealed. The YFSZ led to a thicker and harder alpha-case than the YZ-Blended face-coat. The EDX revealed the presence of Zr and Si elements in both alpha-cases. Therefore, from experimental results and thermodynamic calculations, pure ZrO2and SiO2may react with Ti.

The Effect of CaCO3 Addition on Physical Properties of ZnO-Based Crystal Glaze

2012 ◽  
Vol 620 ◽  
pp. 12-16 ◽  
Author(s):  
Abdul Rashid Jamaludin ◽  
Shah Rizal Kasim ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Calcium Carbonate ◽  
Scanning Electron Microscope ◽  
Physical Properties ◽  
Crystallization Temperature ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The effects of calcium carbonate (CaCO3) addition on the physical properties of ZnO-based crystal glaze batches were investigated. Samples were fired at different gloss firing temperatures ranging from 1180-1220°C with 3 hours soaking at 1060°C crystallization temperature. X-ray diffraction (XRD) analysis identifiedthe crystal phase occurred as willemite (Zn2SiO4) and the scanning electron microscope (SEM) analysis indicated that willemite crystals are in the acicular needle like shape that formed spherulite. The intensities of willemite peaks decreased with CaCO3 addition and completely vanished at 5.0 wt% CaCO3. Varied formation of spherulites developed of the surface of crystal glaze as the flows of the glaze stretched further as the amount of CaCO3 increased.

scholarly journals Application of coconut battery waste to graphic as an alternative electrode on primary battery cells

2019 ◽  
Vol 4 (2) ◽  
pp. 668-673
Author(s):  
Rikson Siburian ◽  
Saur L Raja ◽  
Minto Supeno ◽  
Crystina Simanjuntak
Keyword(s):  
Carbon Sources ◽  
Xrd Analysis ◽  
Coconut Shell ◽  
Thin Plates ◽  
X Ray Diffraction ◽  
X Ray ◽  
Primary Battery ◽  
Diffraction Peaks ◽  
Coconut Shells ◽  
Scanning Electron

Coconut shell is one of the potential biomass as carbon sources. Coconut shell is converted to charcoal through the carbonization process. The potential of charcoal from coconut shells can be synthesized into graphene. Graphene is a derivative of one of the carbon allotropes, namely graphite, where carbon is in the form of thin plates with sp2 orbitals arranged hexagonally. The process of making graphene which is coconut shell dried in the sun then pyrolysis into charcoal then mixed with activated carbon as a reducing agent at 600 ° C for 1 hour to produce graphene. The graphene produced is characterized by X-Ray Diffraction (XRD), Scanning Electron Microscope-Energy Dispersive X-Ray (SEM-EDX). The results by XRD analysis showed the resulting peaks were not sharp and slightly widened at the diffraction peaks at 24 ° and 44 °. The results of SEM-EDX analysis at 4000x magnification show the surface size and shape of the structure that is smaller, thinner and reduced buildup on the graphene structure. graphene that has been successfully synthesized was tested on a coin battery. The coin battery cathode which was replaced with graphene succeeded in turning on the light.  

Sign in / Sign up

Export Citation Format

Share Document