Evaluation of Modified Poly by UV-Induced Graft Polymerization as a Novel Hydrophilic Films

2013 ◽  
Vol 815 ◽  
pp. 594-598
Author(s):  
Bing Qiang Wang
Keyword(s):  
Contact Angle ◽  
Original Film ◽  
Graft Polymerization ◽  
Irradiation Time ◽  
Film Surface ◽  
Ferrous Ammonium Sulfate ◽  
Water Mixture ◽  
Static Contact ◽  
Ferrous Ammonium ◽  
Grafting Degree

In order to improve the hydrophilic performances, the surface of poly films was modified through grafting polymerization of styrene (ST) initiated by ultraviolet (UV) in ethanol/water mixture solution. The effects of irradiation time, concentration of inhibitor (ferrous ammonium sulfate) on the grafting degree of ST will be investigated. The original and grafted poly films were characterized by scanning electron microscopy (SEM) and Static contact angle (CA), to characterize the chemical changes of the poly film surface. The results showed that the hydrophilic of poly films was improved significantly than that of the original film. The contact angle of PO-g-ST increased from 70° to 120.4° over a critical grafting degree of 26.35%, the hydrophilic of PP membranes improved dramatically.

Controlling porosity and density of nanocellulose aerogels for superhydrophobic light materials

TAPPI Journal ◽  
2018 ◽  
Vol 17 (03) ◽  
pp. 145-153 ◽  
Author(s):  
Chengua Yu ◽  
Feng Wang ◽  
Shiyu Fu ◽  
Lucian Lucia
Keyword(s):  
Contact Angle ◽  
Freeze Drying ◽  
Engine Oil ◽  
High Porosity ◽  
Water Mixture ◽  
Waste Engine Oil ◽  
Hydrophobically Modified ◽  
Static Contact ◽  
Oil Water ◽  
Hydrophobic Material

A very low-density oil-absorbing hydrophobic material was fabricated from cellulose nanofiber aerogels–coated silane substances. Nanocellulose aerogels (NCA) superabsorbents were prepared by freeze drying cellulose nanofibril dispersions at 0.2%, 0.5%, 0.8%, 1.0%, and 1.5% w/w. The NCA were hydrophobically modified with methyltrimethoxysilane. The surface morphology and wettability were characterized by scanning electron microscopy and static contact angle. The aerogels displayed an ultralow density (2.0–16.7 mg·cm-3), high porosity (99.9%–98.9%), and superhydrophobicity as evidenced by the contact angle of ~150° that enabled the aerogels to effectively absorb oil from an oil/water mixture. The absorption capacities of hydrophobic nanocellulose aerogels for waste engine oil and olive oil could be up to 140 g·g-1 and 179.1 g·g-1, respectively.

Enhancing oil-sorption performance of polypropylene fiber by surface modification via UV-induced graft polymerization of butyl acrylate

2012 ◽  
Vol 66 (12) ◽  
pp. 2647-2652 ◽  
Author(s):  
Shaoning Li ◽  
Junfu Wei ◽  
Ao Wang ◽  
Yuexia Nie ◽  
Hang Yang ◽  
...  
Keyword(s):  
Sorption Capacity ◽  
Butyl Acrylate ◽  
Graft Polymerization ◽  
Morphological Changes ◽  
Polypropylene Fiber ◽  
Fiber Surface ◽  
Water Mixture ◽  
Retention Performance ◽  
Oil Sorption ◽  
Static Contact

In order to improve oil sorption performances, polypropylene (PP) fiber was modified through graft polymerization with butyl acrylate (BA) initiated by ultraviolet (UV) radiation in isopropanol/water mixture solution. Fourier transform infrared (FT-IR) spectra, scanning electron microscopy (SEM) and specific surface area were used to characterize the chemical and morphological changes of the PP fiber surface. Static contact angle (CA) measurements showed that the hydrophilicity of original PP fiber was enhanced after graft polymerization. The grafted fiber exhibited an excellent oil-sorption, oil-retention performance, fast saturation-sorption rate and superior reusability of oil. When the grafting degree was 15.55%, the maximum oil-sorption capacity reached 18.35 g/g, while the oil-sorption capacity of original PP fiber was only 11.54 g/g. After the tenth cycle of reuse, the grafted fiber sorbent assembly only lost 30% of its virgin sorption capacity.

Correlation of Superhydrophilicity and Photocatalytic Activity in the TiO2-Based Porous Thin Films

2006 ◽  
Vol 510-511 ◽  
pp. 54-57 ◽  
Author(s):  
Seung Yong Chai ◽  
Jin Koo Park ◽  
Ho Kun Kim ◽  
Wan In Lee
Keyword(s):  
Contact Angle ◽  
Photocatalytic Activity ◽  
Uv Irradiation ◽  
Uv Light ◽  
Irradiation Time ◽  
Colloidal Suspension ◽  
Initial Point ◽  
Film Surface ◽  
Contact Angles ◽  
Tio2 Films

Transparent TiO2, WO3-TiO2, and MoO3-TiO2 films were prepared by spin-coating each colloidal suspension. The monolayer coverage of WO3 on the surface of TiO2 greatly increased the photocatalytic activity in the decomposition of gaseous 2-propanol, whereas the addition of MoO3 considerably decreased the photocatalytic reaction of TiO2. For the estimation of superhydrophilicity, the change of contact angles between the water drop and the film surface was measured as a function of UV-irradiation time. The measured contact angle of WO3-TiO2 film was considerably lower than that of TiO2 before the UV-irradiation, and it decreased to the minimum value about 4 times faster than that of pure TiO2 films with the irradiation of UV light. On the other hand, MoO3-TiO2 films showed a low contact angle at initial point, but their contact angle was very slowly decreased under the UV light. The initial low contact angles suggest the high hydrophilic character of WO3-TiO2 and MoO3-TiO2 films with high Lewis surface acidities. The observed trend suggests that the superhydrophilicity is closely related to the photocatalytic activity.

Comparative studies of nitrogen plasma and argon plasma treatment on the strength of PBO fibre reinforced high-temperature resistant thermoplastic composite

2021 ◽  
pp. 095400832098729
Author(s):  
K Sudheendra ◽  
Jennifer Vinodhini ◽  
M Govindaraju ◽  
Shantanu Bhowmik
Keyword(s):  
Contact Angle ◽  
High Temperature ◽  
Plasma Treatment ◽  
Sessile Drop ◽  
Dynamic Contact Angle ◽  
Argon Plasma ◽  
Film Surface ◽  
Fibre Surface ◽  
Nitrogen Plasma ◽  
Thermoplastic Composite

The study involves the processing of a novel poly [1, 4-phenylene-cis-benzobisoxazole] (PBO) fibre reinforced high-temperature thermoplastic composite with polyaryletherketone (PAEK) as the matrix. The PBO fibre and the PAEK film surface was modified using the method of argon and nitrogen plasma treatment. The investigation primarily focuses on evaluating the tensile properties of the fabricated laminates and correlating it with the effect of plasma treatment, surface characteristics, and its fracture surface. A 5% decrease in tensile strength was observed post argon plasma treatment while a 27% increase in strength was observed post nitrogen plasma treatment. The morphology of the failure surface was investigated by scanning electron microscopy and an interfacial failure was observed. Furthermore, the effect of plasma on the wettability of PBO fibres and PAEK film surface was confirmed by the Dynamic Contact Angle analysis and sessile drop method respectively. FTIR spectral analysis was done to investigate the effect of plasma treatment on the chemical structure on the surface. The results of the wettability study showed that the argon plasma treatment of the fibre surface increased its hydrophobicity while nitrogen plasma treatment resulted in the reduction of contact angle.

scholarly journals Biomimetic Approach for the Elaboration of Highly Hydrophobic Surfaces: Study of the Links between Morphology and Wettability

Biomimetics ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 38
Author(s):  
Quentin Legrand ◽  
Stephane Benayoun ◽  
Stephane Valette
Keyword(s):  
Contact Angle ◽  
Ginkgo Biloba ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Textured Surfaces ◽  
Replication Process ◽  
Wetting Behavior ◽  
Static Contact ◽  
Biomimetic Approach ◽  
Highly Hydrophobic

This investigation of morphology-wetting links was performed using a biomimetic approach. Three natural leaves’ surfaces were studied: two bamboo varieties and Ginkgo Biloba. Multiscale surface topographies were analyzed by SEM observations, FFT, and Gaussian filtering. A PDMS replicating protocol of natural surfaces was proposed in order to study the purely morphological contribution to wetting. High static contact angles, close to 135∘, were measured on PDMS replicated surfaces. Compared to flat PDMS, the increase in static contact angle due to purely morphological contribution was around 20∘. Such an increase in contact angle was obtained despite loss of the nanometric scale during the replication process. Moreover, a significant decrease of the hysteresis contact angle was measured on PDMS replicas. The value of the contact angle hysteresis moved from 40∘ for flat PDMS to less than 10∘ for textured replicated surfaces. The wetting behavior of multiscale textured surfaces was then studied in the frame of the Wenzel and Cassie–Baxter models. Whereas the classical laws made it possible to describe the wetting behavior of the ginkgo biloba replications, a hierarchical model was developed to depict the wetting behavior of both bamboo species.

Effect of Water Temperature, pH Value, and Film Thickness on the Wettability Behaviour of Copper Surfaces Coated with Copper Using EB-PVD Technique

2019 ◽  
Vol 60 ◽  
pp. 124-141 ◽  
Author(s):  
Naser Ali ◽  
Joao Amaral Teixeira ◽  
Abdulmajid Addali
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Film Thickness ◽  
Water Temperature ◽  
Ph Value ◽  
Surface Wettability ◽  
Copper Surfaces ◽  
Force Microscopy ◽  
Atomic Force ◽  
Static Contact

This research investigates the effect of surface roughness, water temperature, and pH value on the wettability behaviour of copper surfaces. An electron beam physical vapour deposition technique was used to fabricate 25, 50, and 75 nm thin films of copper on the surface of copper substrates. Surface topographical analysis, of the uncoated and coated samples, was performed using an atomic force microscopy device to observe the changes in surface microstructure. A goniometer device was then employed to examine the surface wettability of the samples by obtaining the static contact angle between the liquid and the attached surface using the sessile drops technique. Waters of pH 4, 7, and 9 were employed as the contact angle testing fluids at a set of fixed temperatures that ranged from 20°C to 60°C. It was found that increasing the deposited film thickness reduces the surface roughness of the as-prepared copper surfaces and thus causing the surface wettability to diverge from its initial hydrophobic nature towards the hydrophilic behaviour region. A similar divergence behaviour was seen with the rise in temperature of water of pH 4, and 9. In contrast, the water of pH 7, when tested on the uncoated surface, ceased to reach a contact angle below 90o. It is believed that the observed changes in surface wettability behaviour is directly linked to the liquid temperature, pH value, surface roughness, along with the Hofmeister effect between the water and the surface in contact.

The Surface Modification with Fluorocarbon Thin Films for the Prevention of Stiction in Mems

1998 ◽  
Vol 518 ◽  
Author(s):  
Sang-Ho Lee ◽  
Myong-Jong Kwon ◽  
Jin-Goo Park ◽  
Yong-Kweon Kim ◽  
Hyung-Jae Shin
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Fluorocarbon Films ◽  
Perfluorodecanoic Acid ◽  
Large Hysteresis ◽  
Static Contact ◽  
Receding Contact ◽  
Highly Hydrophobic ◽  
Receding Contact Angle

AbstractHighly hydrophobic fluorocarbon films were prepared by the vapor phase (VP) deposition method in a vacuum chamber using both liquid (3M's FC40, FC722) and solid sources (perfluorodecanoic acid (CF3(CF2)8COOH), perfluorododecane (C12F26)) on Al, Si and oxide coated wafers. The highest static contact angles of water were measured on films deposited on aluminum substrate. But relatively lower contact angles were obtained on the films on Si and oxide wafers. The advancing and receding contact angle analysis using a captive drop method showed a large contact angle hysteresis (ΔH) on the VP deposited fluorocarbon films. AFM study showed poor film coverage on the surface with large hysteresis. FTIR-ATR analysis positively revealed the stretching band of CF2 groups on the VP deposited substrates. The thermal stability of films was measured at 150°C in air and nitrogen atmospheres as a function of time. The rapid decrease of contact angles was observed on VP deposited FC and PFDA films in air. However, no decrease of contact angle on them was observed in N2.

The Pressure Drop and Dynamic Contact Angle of Motion of Triple-Lines in Hydrophobic Microchannels

2010 ◽  
Author(s):  
Dongin Yu ◽  
Chiwoong Choi ◽  
Moohwan Kim
Keyword(s):  
Contact Angle ◽  
Pressure Drop ◽  
Liquid Film ◽  
Dynamic Contact Angle ◽  
Triple Line ◽  
Dynamic Contact ◽  
Superficial Velocity ◽  
Channel Diameter ◽  
Fluid Property ◽  
Static Contact

At two-phase flow in microchannels, slug flow regime is different for wettability of surface. A slug in a hydrophilic microchannel has liquid film. However, a slug in a hydrophobic microchannel has no liquid film instead, the slug has triple-lines and makes higher pressure drop due to the motion of the triple-line. In previous researches, pressure drop of triple-line is depended of dynamic contact angle, channel diameter and fluid property. And, dynamic contact angle is depended of static contact angle, superficial velocity and fluid property. In order to understand the pressure drop of motion of triple-lines, pressure drop of slug with triple-lines in case of various diameters (0.546, 0.763, 1.018, 1.555, 2.075 mm), various fluids (D.I.water, D.I.water-1, 5, 10% ethanol mixture) and various superficial velocity (j = 0.01∼0.4 m/s) was measured. Dynamic contact angle was calculated from relation of the pressure drop of slug with triple-lines. Comparing with previous dynamic contact angle correlations, previous correlation underestimated dynamic contact angle in the region of this study. (10−4≤Ca≤10−3, 10−2≤We≤10−1, 68°≤θS≤110°)

Sign in / Sign up

Export Citation Format

Share Document