Acetylated African Oil Bean Seed Pod For Crude Oil Spill Mop

Oil spill remediation has continued to be a challenge in the world today. Thus efforts are still been made to develop more efficient oil spill mop up techniques. Natural adsorption with agricultural wastes, which otherwise constitute environmental pollution, has become an attractive technique for oil spill mop. Acetylation using acetic anhydride with iodine catalyst was carried out to improve the hydrophobicity of African oil bean seed pod (AOBSP), which is a lignocellulosic material and as such is naturally hydrophilic. Characterization of the raw and acetylated AOBSP were done using SEM, BET and FTIR analyses. Batch crude oil sorption tests were performed using both the raw and acetylated AOBSP. Isotherm, kinetic and thermodynamic studies were also carried out. FTIR analysis showed evidence of successful acetylation of AOBSP and adsorption of crude oil onto the raw and acetylated AOBSP. SEM and BET analyses showed improvement of the surface properties of AOBSP by the acetylation process. The BET surface area increased from 226.4 m2/g for the raw AOBSP to 310.0 m2/g for the acetylated AOBSP. Oil sorption was found to be by monolayer coverage, with monolayer sorption capacity of 5000mg/g and 12500mg/g for raw and acetylated AOBSP, respectively. The rate-controlling mechanism for the sorption processes was chemisorption. Negative values of ΔGo, ΔHo and ΔSo were obtained, showing that the sorption processes were feasible, spontaneous and exothermic, with a degree of orderliness at the solid–mixture interface. The results obtained from this study show that both raw and acetylated AOBSP are efficient oil sorbents with potentials for further improvement for oil spill mop.

Characteristics and oil sorption effectiveness of areca nut husk

Oil spill accident occur due to human carelessness and error during oil transportation, storage, and production of the hydrocarbon. Effect of oil spill can be either short or long term. It is not only affecting the environment but also marine life, economy, and social. Thus, effective recovery and control method must be carefully implemented to minimise the effect. There are various studies and technologies to mitigate the oil spill incident but mostly the techniques are very expensive, difficult and use of non-environmental friendly material. Hence, this study is conducted to study areca nut husk as a potential oil adsorbent for oil spill recovery. The characteristics of areca nut husk include morphological structures and chemical composition. The areca nut husk oil sorption effectiveness and capacity also been investigated. Areca nut husk were tested for both heavy crude oil and diesel adsorption. The result shows that the efficiency of oil sorption of areca nut husk toward heavy crude oil is 14.8% and it can be an alternative sorbent material to the current modern material. Meanwhile, the areca nut husk is not recommended to be used for diesel absorption activity for its low effectiveness (i.e., 2.04%) showed in this study.

Recovery of Waste Polyurethane from E-Waste—Part I: Investigation of the Oil Sorption Potential

The shredding of end-of-life refrigerators produces every year in Italy 15,000 tons of waste polyurethane foam (PUF), usually destined for energy recovery. This work presents the results of the investigation of the oil sorption potential of waste PUF according to ASTM F726–17 standard. Three oils (diesel fuel and two commercial motor oils) having different densities (respectively, 0.83, 0.87, and 0.88 kg/dm3) and viscosities (respectively, 3, 95, and 140 mm2/s at 40 °C) were considered. The waste PUF was sampled in an Italian e-waste treatment plant, and its characterization showed 16.5 wt% particles below 0.71 mm and 13 wt% impurities (paper, plastic, aluminum foil), mostly having dimensions (d) above 5 mm. Sieving at 0.071 mm was applied to the waste PUF to obtain a “coarse” (d > 0.71 mm) and a “fine” fraction (d < 0.71 mm). Second sieving at 5 mm allowed an “intermediate” fraction to be obtained, with dimensions between 0.71 and 5 mm. The oil sorption tests involved the three fractions of waste PUF, and their performances were compared with two commercial oil sorbents (sepiolite and OKO-PUR). The results of the tests showed that the “fine” PUF was able to retain 7.1–10.3 g oil/g, the “intermediate” PUF, 4.2–7.4 g oil/g, and the “coarse” PUF, 4.5–7.0 g oil/g, while sepiolite and OKO-PUR performed worse (respectively, 1.3–1.6 and 3.3–5.3 g oil/g). In conclusion, compared with the actual management of waste PUF (100 wt% sent to energy recovery), the amount destined directly to energy recovery could be limited to 13 wt% (i.e., the impurities). The remaining 87 wt% could be diverted to reuse for oil sorption, and afterward directed to energy recovery, considered as a secondary option.

Removing free-floating oil from water using cationic polymers/surfactant-modified silica

The purpose of this work was to evaluate the efficiency of oil sorption of silica particles modified by three different types of cationic polymers and a cationic surfactant. Low-molecular-weight polyethyleneimine (LPEI), high-molecular-weight polyethyleneimine (HPEI), polydiallyldimethylammonium chloride (PDM), and cetyltrimethylammonium bromide (CTAB) were used to modify the silica particles and then compared their performances for oil removal. The scanning electron microscope and zeta potential measurements were used to analyze the surface characteristics of unmodified and modified silica particles. Adsorptions of motor oil and palm oil on the modified silica particles have been investigated under various parameters such as the silica particle size, the oil concentration, the polymer/surfactant concentrations, and the pH. The results have shown that the modified silica particles enhanced the oil sorption ability by approximately 10–20 times depending on the size of silica particles, pH, and the type of polymer/surfactant used when compared with the unmodified silica particles. The highest palm oil adsorption values of LPEI-silica, HPEI-silica, PDM-silica, CTAB-silica, and unmodified silica were 2.40, 2.10, 1.95, 1.50, and 0.15 g/gsilica, respectively. Moreover, the oil sorption of the modified silica particles was increased by approximately 30–50% for the smallest-sized silica particles.

Efficiency of castor oil–based polyurethane foams for oil sorption S10 and S500: Influence of porous size and statistical analysis

This study evaluates the efficiency of castor oil–based polyurethane foams for oil sorption S10 and S500, focusing on the influence of the pores’ size. Different foams were produced by varying the polyol: isocyanate ratio (1:0.3; 1:0.5; 1:1.0; 1:1.5; and 1:2.0). The physicochemical properties, morphology, density, and Hg porosity were determined. The sorption capacity was influenced by exposure time, oil viscosity, and concentration of the reagents, considering variations in the hydrophobicity, void content, and morphology. The results showed that the foam produced at an in the same mass proportion (PUC) has a higher sorption capacity in exposure time from 25 to 40 h due to higher void content and larger pore diameter size. It was observed that the lower viscosity of S10 diesel contributes to the higher sorption efficiency compared to S500 one. The Taguchi method corroborated the mentioned results, indicating a higher sorption trend by varying the reagent concentration and exposure times.

Oil spill cleanup by natural fibers: a review

Purpose In recent years, oil spill pollution has become one of the main problems of environmental pollution. Recovering oil by means of sorbent materials is a very promising approach and has acquired more attention due to its high cleanup efficiency. Compared to synthetic fibrous sorbents, the use of natural fibers in oil spill cleanups offers several advantages including environmental friendliness, degradable features and cost-effectiveness. Therefore, studies on developing sorbents using natural fibers for oil spill cleanup applications have become a research hotspot. Design/methodology/approach This paper reviews the work conducted by several researchers in developing oil sorbents from fibers such as cattail, nettle, cotton, milkweed, kapok, populous seed fiber and Metaplexis japonica fiber. Some featured critical parameters influencing the oil sorption capacity of fibrous substrates are discussed. Oil sorption capacity and reusability performance of various fibers are also discussed. Recent developments in oil spill cleanups and test methods for oil sorbents are briefly covered. Findings The main parameters influencing the oil sorption capacity of sorbents are fiber morphological structure, fiber density (g/cc), wax (%), hollowness (%) and water contact angle. An extensive literature review showed that oil sorption capacity is highest for Metaplexis japonica fiber followed by populous seed fiber, kapok, milkweed, cotton, nettle and cattail fiber. After use, the sorbents can be buried under soil or they can also be burned so that they can be vanished from the surface without causing environmental-related issues. Originality/value This review paper aims to summarize research studies conducted related to various natural fibers for oil spill cleanups, fiber structural characteristics influencing oil sorption and recent developments in oil spill cleanups. This work will inspire future researchers with various knowledge backgrounds, particularly, from a sustainability perspective.

Oil Sorption Performance of Sorbent Materials Examined Under Static and Dynamic Conditions

Oil spill cleanup and subsequent restoration of the environment is majorly a function of spill cleanup methods applied. Some of these methods, though efficient, are, however, very expensive and require more personnel for their application and relative deployment in the field. The study was aimed at examining the efficiency of a locally and readily available, eco-friendly and low cost agricultural waste (coconut husk coir) as sorbent materials for spilled engine oil cleanup under static and dynamic marine water conditions. The sorbent material was prepared and used in three forms: raw coconut husk coir (CHC), modified coconut husk coir (MCHC), and reused coconut husk coir (RCHC). Under static and dynamic marine water conditions, oil sorption batch equilibrium experiments were used to study the engine oil sorption capacity and efficiency of the sorbent. Effects of sorbent dosage and sorption times on the oil sorption and efficiency of CHC, MCHC, and RCHC were studied and determined. At a constant sorption time of 60 minutes and varying sorbent dosages of 2-8 /320 ml of engine oil-marine water concentration, MCHC exhibited the highest oil sorption efficiency of 61.18% and 44.33% for dynamic and static conditions, CHC had 55.61% and 38.50% for dynamic and static conditions, whereas RCHC had 41.66% and 26.04% for dynamic and static conditions, respectively. It is statistically deduced from the results that sorption times and sorbent dosages have significant effects on the sorption efficiency of experimental coir for spilled engine oil removal. Though there is a need for proper blending or modifications of the sorbent material to enhance its affinity to oil and hydrophobicity, there are enough potentials in the materials for mild marine water current spilled engine oil cleanup.

The study of hydrophobicity and oleophilicity of 3D weft-knitted spacer fabrics integrated with silica aerogels

The interest in multifunctional textile materials has been increased due to the health and safety measures of living beings, especially in severe conditions. Therefore, this study investigated the hydrophobicity, oil sorption capacity, and bending properties of untreated or uncoated and treated or coated 3D weft-knitted spacer fabric samples (92% polyester/8% spandex), i.e. sample 1, sample 2, and sample 3, having thicknesses of 2 mm (300 gm−2), 3 mm (350 gm−2), and 4 mm (540 gm−2), with silica aerogels (SAs) through the sol-gel method. SEM, FTIR-ATR, and surface roughness test of fabric samples were analyzed to comprehend the influence of SAs. The experimental results revealed the excellent hydrophobicity and oleophilicity of all the treated 3D weft-knitted spacer fabric samples, providing a higher water contact angle (CA) 142 ± 0.84° and an oil sorption capacity 7.51 ± 0.08g/g and 6.88 ± 0.06g/g for vegetable oil and engine oil, especially of sample 2 owing to the most silica particles. The statistical analysis also demonstrated a significant performance (P < 0.05) of treated spacer fabric samples at the 0.05 level. Thus, these fabrics are suitable for an industrial application of hydrophobic and oleophilic properties.