Autoclaving Time Influence on Fly Ash Aerated Concrete Compressive Strength and Microstructure

2014 ◽  
Vol 897 ◽  
pp. 301-304
Author(s):  
Ester Helanová ◽  
Rostislav Drochytka ◽  
Radek Janovský
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Hydrothermal Reaction ◽  
Raw Materials ◽  
Concrete Strength ◽  
Use Value ◽  
Environmental Aspects ◽  
Concrete Compressive Strength ◽  
Modern Material ◽  
Aerated Concrete

The fly ash aerated concrete is a modern material combining high use value with environmental aspects of its production. It is mainly an utilisation of secondary raw materials with related minimum consumption of natural resources. The resulting properties the aerated concrete product obtains by autoclaving during which a complete line of calcium hydro silicates are formed due to occurring hydrothermal reaction and tobermorite mineral is the most important one. This mineral has a significant influence principally on aerated concrete strength. This article thus verifies the autoclaving time influence on tobermoritic phase developments and to this related compressive strength of the fly ash aerated concrete.

scholarly journals Assessment of the influence of fly ash additive on the tightness of concrete with furnace cement CEM IIIA 32,5N

2017 ◽  
Vol 66 (4) ◽  
pp. 153-164
Author(s):  
Anna Szcześniak ◽  
Jacek Zychowicz ◽  
Adam Stolarski
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Concrete Strength ◽  
Concrete Compressive Strength ◽  
Water Penetration ◽  
Laboratory Investigations ◽  
Concrete Testing ◽  
Water Tightness

The analysis of influence of fly ash additive to concrete on the basis of cement CEM IIIA 32,5 N on the tightness and strength was presented in the paper. Researches were carried out for three types of concrete made with the use of CEM IIIA 32,5N LH HSR NA cement. The basic recipe of concrete does not contain the additive of fly ash, while two other concretes contain the fly ash additive in an amount of 25% and 33% of the cement mass. Laboratory investigations of the concrete samples were carried out under conditions of long-term maturation in the range of the water tightness and the depth of water penetration in concrete, compressive strength and tensile strength of concrete at splitting. Keywords: concrete testing, furnace cement, fly ash additive, water tightness of concrete, strength of concrete.

scholarly journals INOVASI BETON RAMAH LINGKUNGAN

2020 ◽  
Vol 6 (2) ◽  
Author(s):  
Masri A Rivai ◽  
Sudirman Kimi ◽  
Revisdah Revisdah
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Normal Condition ◽  
Glass Powder ◽  
Concrete Strength ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Concrete Mix ◽  
Compressive Strength Of Concrete

In this study the author take Fly Ash and Powder Glass as an added ingredient in the concrete mix. This research intend to know the effect of Fly Ash and Powder Glass on K-300 concrete compressive strenght.This study uses cube-shaped specimens with the siza of 15 x 15 x 15. The total of test specimens in this study as much as 45 sample, each 9 seal of test specimens in 5 condition that is normal, concrete + fly ash 5% + glass powder 18%, concrete + fly ash 5% + glass powder 21%, concrete + fly ash 5% + glass powder 24%, concrete + fly ash 5% + glass powder 27%.After concrete compressive strenght test, the concrete strength og the concrete at age 3, 7 and 28 days with normal condition at 3 days age aqual to 139.26 Kg/Cm2, at age 7 day equal to 202.17 Kg/Cm2 and age 28 day of 307.01 Kg/Cm2. And the value of compressive strength of concrete characteristic with the use of Fly Ash 5% + glass powder 18% has the highest value of concrete compressive strength that is at 3 days age of 151.13 Kg/Cm2, 7 day age equal to 21175 Kg/Cm2 and age 28 is 312.81 Kg/Cm2 . These result exceed the copressive strength values of normal concrete characteristic and show that fly ash and glass powder can increase the compressive of the concrete.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

scholarly journals Effect of Fly Ash on Compressive Strength, Drying Shrinkage, and Carbonation Depth of Mortar with Ferronickel-Slag Powder

2021 ◽  
Vol 11 (3) ◽  
pp. 1037
Author(s):  
Se-Jin Choi ◽  
Ji-Hwan Kim ◽  
Sung-Ho Bae ◽  
Tae-Gue Oh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Bituminous Coal ◽  
Raw Materials ◽  
Drying Shrinkage ◽  
The Other ◽  
Test Results ◽  
Slag Powder ◽  
Ferronickel Slag

In recent years, efforts to reduce greenhouse gas emissions have continued worldwide. In the construction industry, a large amount of CO2 is generated during the production of Portland cement, and various studies are being conducted to reduce the amount of cement and enable the use of cement substitutes. Ferronickel slag is a by-product generated by melting materials such as nickel ore and bituminous coal, which are used as raw materials to produce ferronickel at high temperatures. In this study, we investigated the fluidity, microhydration heat, compressive strength, drying shrinkage, and carbonation characteristics of a ternary cement mortar including ferronickel-slag powder and fly ash. According to the test results, the microhydration heat of the FA20FN00 sample was slightly higher than that of the FA00FN20 sample. The 28-day compressive strength of the FA20FN00 mix was approximately 39.6 MPa, which was higher than that of the other samples, whereas the compressive strength of the FA05FN15 mix including 15% of ferronickel-slag powder was approximately 11.6% lower than that of the FA20FN00 mix. The drying shrinkage of the FA20FN00 sample without ferronickel-slag powder was the highest after 56 days, whereas the FA00FN20 sample without fly ash showed the lowest shrinkage compared to the other mixes.

scholarly journals Evaluation of Self-Compacting Concrete Strength with Non-Destructive Tests for Concrete Structures

2019 ◽  
Vol 9 (23) ◽  
pp. 5109 ◽  
Author(s):  
Miguel C. S. Nepomuceno ◽  
Luís F. A. Bernardo
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Surface Hardness ◽  
Pulse Velocity ◽  
Concrete Compressive Strength ◽  
Self Compacting Concrete ◽  
Coarse Aggregates ◽  
Pull Out ◽  
Concrete Maturity ◽  
Non Destructive

Self-compacting concrete (SCC) shows to have some specificities when compared to normal vibrated concrete (NVC), namely higher cement paste dosage and smaller volume of coarse aggregates. In addition, the maximum size of coarse aggregates is also reduced in SCC to prevent blocking effect. Such specificities are likely to affect the results of non-destructive tests when compared to those obtained in NVC with similar compressive strength and materials. This study evaluates the applicability of some non-destructive tests to estimate the compressive strength of SCC. Selected tests included the ultrasonic pulse velocity test (PUNDIT), the surface hardness test (Schmidt rebound hammer type N), the pull-out test (Lok-test), and the concrete maturity test (COMA-meter). Seven sets of SCC specimens were produced in the laboratory from a single mixture and subjected to standard curing. The tests were applied at different ages, namely: 1, 2, 3, 7, 14, 28, and 94 days. The concrete compressive strength ranged from 45 MPa (at 24 h) to 97 MPa (at 94 days). Correlations were established between the non-destructive test results and the concrete compressive strength. A test variability analysis was performed and the 95% confidence limits for the obtained correlations were computed. The obtained results for SCC showed good correlations between the concrete compressive strength and the non-destructive tests results, although some differences exist when compared to the correlations obtained for NVC.

scholarly journals PEMANFAATAN LIMBAH FLY ASH DARI PEMBAKARAN BATUBARA PADA PEMBUATAN SEMEN PCC (PORTLAND COMPOSITE CEMENT) DI PT SEMEN XYZ LAMPUNG

2020 ◽  
Vol 4 (2) ◽  
Author(s):  
Dwi Septiyana Sari ◽  
◽  
Susanti Sundari
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Raw Materials ◽  
Testing Machine ◽  
Technical Aspect ◽  
Raw Material ◽  
Physical Test ◽  
Composite Cement ◽  
The Difference ◽  
The Cost

Abstract This study discusses the use of fly ash waste from coal burning on the manufacture of PCC (Portland composite cement) at PT. XYZ Lampung. The purpose of this research is to look at the technical studies and the efficiency of raw materials in the use of fly ash in cement making, in this case PCC cement (Portland Composite Cement). The steps taken in analyzing the data in this study were viewed from a technical aspect by means of a physical test, namely the cement compressive strength test at the age of 3 days, 7 days, and 28 days using the Compression Testing Machine. This test was conducted to see the comparison of the compressive strength of PCC cement using limestone and fly ash as raw materials, then calculate the difference in raw material costs in the year before and after the replacement of limestone with fly ash. The results showed that cement with the addition of fly ash after 3 days, 7 days and 28 days had an increased compressive strength value, which increased 21.69%, 16.07% and 8.05% respectively of the compressive strength of cement using limestone. The use of fly ash as a substitute for limestone has an effect on the cost of raw materials, where the difference between the cost of raw materials in 2019 and the cost of raw materials in 2018 is Rp. 39,440,952,074.

scholarly journals Experimental study on the effect of concrete strength and corrosion level on bond between steel bar and concrete

2021 ◽  
Vol 72 (4) ◽  
pp. 498-509
Author(s):  
Vuong Doan Dinh Thien ◽  
Hung Nguyen Thanh ◽  
Hung Nguyen Dinh
Keyword(s):  
Compressive Strength ◽  
Bond Strength ◽  
Concrete Strength ◽  
Concrete Block ◽  
Bond Stress ◽  
Concrete Compressive Strength ◽  
Pull Out ◽  
Steel Bar ◽  
Stress Degradation ◽  
Slip Displacement

Corrosion of the steel reinforcement bars reduces the area of the steel bar and the bond stress between the steel bars and around concrete that decreases the capacity of concrete structures. In this study, the bond stress between steel bar with a diameter of 12mm and concrete was examined with the effect of different corrosion levels and different concrete grades. A steel bar was inserted in a concrete block with a size of 20×20×20cm. The compressive strength of concrete was 25.6MPa, 35.1MPa, and 44.1MPa. These specimens were soaked into solution NaCl 3.5% to accelerate the corrosion process with different corrosion levels in the length of 60mm. The pull-out test was conducted. Results showed that the bond strength of the corroded steel bar was higher than that predicted from CEB-FIP. Slip displacement and the range of slip displacement at the bond strength were reduced when the concrete compressive strength was increased. The rate of bond stress degradation occurred faster with the increment of the corrosion level when the concrete compressive strength was increased.

scholarly journals Kuat Tekan Beton Mutu Tinggi dengan Memanfaatkan Fly Ash dan Bubuk Kaca Sebagai Bahan Pengisi

2020 ◽  
Vol 20 (01) ◽  
pp. 61-68
Author(s):  
Siska Apriwelni ◽  
Nugraha Bintang Wirawan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Glass Powder ◽  
Concrete Mixture ◽  
Strength Testing ◽  
Concrete Compressive Strength ◽  
High Quality ◽  
Glass Waste ◽  
Powder Addition ◽  
Compressive Strength Of Concrete

(ID) Penelitian ini membahas pengaruh kuat tekan beton mutu tinggi dengan memanfaatkan limbah fly ash dan limbah kaca. Tujuan dari penelitian ini untuk mengetahui kuat tekan beton pada masing-masing variasi, mengetahui persentase campuran beton untuk menghasilkan kuat tekan maksimum, dan mengetahui apakah fly ash dan serbuk kaca efektif digunakan secara bersamaan sebagai bahan campuran beton. Komposisi fly ash terdiri dari 5 variasi yaitu persentase 0%, 5%, 10%, 15%, dan 20%. Sedangkan untuk komposisi serbuk kaca terdiri dari 2 variasi yaitu persentase 5% dan 10%. Jumlah benda uji 30 buah silinder berukuran diameter 15 cm dan tinggi 30 cm dengan 3 benda uji untuk setiap variasi. Perencanaan campuran beton menggunakan SNI 03-2834-2000 yang dimodifikasi. Pengujian kuat tekan diuji pada umur beton 28 hari. Beton dengan fly ash 0% dan serbuk kaca 10% memiliki kuat tekan paling tinggi dibandingkan dengan beton dengan tambahan fly ash, yaitu 46,77%. Selain itu, dapat disimpulkan bahwa semakin bertambahnya jumlah persentase serbuk kaca yang digunakan menunjukkan bahwa kuat tekan beton semakin bertambah juga. Penambahan fly ash pada campuran beton mempengaruhi kuat tekan beton yang dihasilkan. Pada variasi fly ash 0% memiliki kuat tekan tertinggi baik pada saat campuran serbuk kaca 5%dan 10%. Variasi fly ash 15% adalah kondisi optimum campuran beton dengan kuat tekan beton yaitu 43,31 Mpa. Kedua limbah ini dapat dikombinasikan dan dimanfaatkan dengan baik dan digunakan dalam pembuatan beton mutu tinggi. (EN) This study discusses the effect of high quality concrete by utilizing fly ash and glass waste. The purpose of this study is to determine the compressive strength of concrete in each variation, to determine the contribution of concrete to produce compressive strength, and to find out that fly ash and glass powder are effectively used in full as a concrete admixture. Fly ash composition consists of 5 variations, namely the percentage of 0%, 5%, 10%, 15%, and 20%. While for the composition of glass powder consists of 2 variations, namely the percentage of 5% and 10%. The number of specimens is 30 cylinders with a diameter of 15 cm and a height of 30 cm with 3 specimens for each variation. Concrete mixture planning using SNI 03-2834-2000 was developed. Compressive strength testing on concrete age 28 days. Concrete with 0% fly ash and 10% glass powder have the highest compressive strength compared to concrete with additional fly ash, which is 46.77%. In addition, it can increase the amount of glass powder addition that is used to show the concrete compressive strength is increasing as well. The addition of fly ash in the concrete mixture has an effect on the compressive strength of the concrete produced. In the variation of 0% fly ash has the highest compressive strength when the glass powder mixture of 5% and 10%. The 15% fly ash variation is the optimal concrete mixture with compressive strength of 43.31 MPa. These two wastes can be combined and utilized properly and are used in making high quality concrete.  

EFFECTS OF REPLACING CEMENT BY DATE PALM TREES WASTES ON CONCRETE PERFORMANCE

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Ahmad Salah Edeen Nassef ◽  
Kalifa Hamed AlMuqbali ◽  
Sheikha Mahmood Al Naqabi
Keyword(s):  
Compressive Strength ◽  
Date Palm ◽  
Cement Content ◽  
Concrete Strength ◽  
Palm Tree ◽  
Compression Tests ◽  
Tree Leaves ◽  
Concrete Compressive Strength ◽  
Sustainable Environment ◽  
Palm Trees

This paper was studying the effects of palm tree wastes on the behavior of the concrete to reduce cement content in the concrete to ensure a sustainable environment. Both fibers of palm tree and the ash of palm tree leaves are used in this study considering different percentages of palm tree wastes, which are replaced the cement, to investigate both of workability and strength of the concrete. Also, the combination of palm tree leaves ash and fibers of palm trees is investigated. The slump and compression tests are carried out to evaluate both workability and concrete strength. The palm fibers were reducing the workability of concrete at both of different percentage of replacement and different fiber lengths. The slump is reduced by 26.667% at 2 cm fibers length and it is completely lost at 5 cm length fibers at the same percentage of replacement of 5% of the cement content. The palm fibers were weakening concrete compressive strength at different percentages and different fiber lengths. Palm leaves ash was enhancing concrete workability and concrete compressive strength.

Use of Water Glass from Rice Husk and Bagasse Ashes in the Preparation of Fly Ash Based Geopolymer

2019 ◽  
Vol 798 ◽  
pp. 364-369 ◽  
Author(s):  
Khemmakorn Gomonsirisuk ◽  
Parjaree Thavorniti
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Ball Mill ◽  
Water Glass ◽  
Rice Husk Ash ◽  
Raw Materials ◽  
Agricultural Waste ◽  
Preparation Process

The aim of this work is to study the feasibility of preparation of fly ash based geopolymer using sodium water glass from agricultural waste as alternative activators. Rice husk ash and bagasse ash were used as raw materials for producing sodium water glass solution. The sodium water glass were produced by mixing rice husk ash and bagasse ash with NaOH in ball mill and boiling. The prepared sodium water glass were analyzed and used in geopolymer preparation process. The geopolymer paste were prepared by adding the obtained water glass and NaOH with fly ash. After cured at ambient temperature for 7 days, mechanical properties were investigated. Bonding and phases of the geopolymer were also characterized. The geopolymer from rice husk ash presented highest compressive strength about 23 MPa while the greatest for bagasse ash was about 16 MPa.

Sign in / Sign up

Export Citation Format

Share Document