Strength and Toughness of 1.1wt% Li-Containing Al-Zn-Mg-Cu Alloys

2007 ◽  
Vol 353-358 ◽  
pp. 392-395 ◽  
Author(s):  
Zhong Kui Zhao ◽  
Tie Tao Zhou ◽  
Pei Ying Liu ◽  
Chang Qi Chen
Keyword(s):  
Electron Microscopy ◽  
Fracture Toughness ◽  
Impact Test ◽  
Scanning Electron Microscopy Micrographs ◽  
High Toughness ◽  
Cu Alloys ◽  
Transmission Electron ◽  
Ageing Processes ◽  
The Impact ◽  
Scanning Electron

The effect of ageing processes on the toughness and the yield strength of the Li-containing Al-Zn-Mg-Cu alloys (Al-5.6%Zn-1.9%Mg-1.6%Cu-1.1%Li-0.24Cr) was investigated. The microstructure was observed by transmission electron microscopy, tensile test was performed at a rate of 1mm·s-1, fracture toughness was experimentally determined by the impact test, and the fracture modes had been assessed by image analysis of scanning electron microscopy micrographs. The strength of the Li-containing Al-Zn-Mg-Cu alloys treated at 120 °C is not more than 430MPa, which is very lower than that of 7075 alloys. The strength is comparable to that of 7075–T6 alloys after double-ageing or multi-ageing, however its ductility is lower than that of 7075-T6 alloys. The single-aged Li-containing alloys have high toughness. The multi-aged alloys become brittle. The fracture surface for the Li-containing Al-Zn-Mg-Cu alloys is intergranular, since the intergranular precipitation weakness the grain boundaries.

Organoclay-reinforced polyethersulfone-modified epoxy-based hybrid nanocomposites

2011 ◽  
Vol 23 (7) ◽  
pp. 526-534 ◽  
Author(s):  
Yang Wang ◽  
Boming Zhang ◽  
Jinrui Ye
Keyword(s):  
Electron Microscopy ◽  
Fracture Toughness ◽  
Electron Microscope ◽  
Optical Microscope ◽  
Mechanical Analysis ◽  
Hybrid Nanocomposites ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Modified Epoxy ◽  
Scanning Electron

Hybrid nanocomposites were successfully prepared by the incorporation of polyethersulfone (PES) and organoclay into epoxy resin. They had higher fracture toughness than the prepared PES/epoxy blend and organoclay/epoxy nanocomposites. The microstructures of the hybrid nanocomposites were studied. They were comprised of homogeneous PES/epoxy semi-interpenetrating network (semi-IPN) matrices and organoclay micro-agglomerates made up of tactoid-like regions composed of ordered exfoliated organoclay with various orientations. The former was confirmed with dynamic mechanical analysis, scanning electron microscopy and transmission electron microscopy, while the latter was successfully observed with X-ray diffraction measurements, optical microscope, scanning electron microscope and transmission electron microscope. The improvement of their fracture toughness was due to the synergistic toughening effect of the PES and the organoclay and related to their microstructures.

Impact and Thermal Properties of Unsaturated Polyester (UPR) Composites Filled with Empty Fruit Bunch Palm Oil (EFBPO) and Cellulose

2014 ◽  
Vol 896 ◽  
pp. 310-313 ◽  
Author(s):  
Elmer Surya ◽  
Michael ◽  
Halimatuddahliana ◽  
Maulida
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Palm Oil ◽  
Impact Test ◽  
Unsaturated Polyester ◽  
Empty Fruit Bunch ◽  
Infra Red ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

In this research, the impact properties of unsaturated polyester (UPR) composites filled with empty fruit bunch palm oil (EFBPO) and cellulose were investigated. The composites were made by hand-lay up method by mixing UPR with the content of each fillers (EFBPO and cellulose) of 5,10,15,20 wt.%. The parameter which was carried out on the prepared samples was impact test. It was found that the addition of fillers to the matrix caused the impact strength of composites increased at 10% addition of EFBPO and 5% addition of cellulose. The results were confirmed by fourier transform infra-red (FTIR) and supported by thermogravimetric analysis (TGA) and scanning electron microscopy (SEM).

scholarly journals Study on strength and fracture toughness of Al-Zn-Mg-Cu-Ti(-Sn) alloys

2015 ◽  
Vol 51 (1) ◽  
pp. 73-79 ◽  
Author(s):  
A. Yan ◽  
L. Chen ◽  
H.S. Liu ◽  
F.F. Xiao ◽  
X.Q. Li
Keyword(s):  
Electron Microscopy ◽  
Fracture Toughness ◽  
Transmission Electron Microscopy ◽  
Second Phase ◽  
Plane Strain Fracture Toughness ◽  
Optical Scanning ◽  
Transmission Electron ◽  
Strain Fracture ◽  
Second Phase Particles ◽  
Scanning Electron

The strength and fracture toughness of Al-Zn-Mg-Cu-Ti(-Sn) alloys were investigated by performing tensile and plane strain fracture toughness (KIC) tests. Detailed observations with optical, scanning electron and transmission electron microscopy were conducted to analyze microstructure and fracture surfaces of the alloys. The results revealed that addition of Sn refined the solution-aging grain size of matrix and reduced coarsening rate of precipitate during aging. Narrower precipitation free zones and more discontinuous distribution of grain boundary precipitates were observed to be displayed in the Sn-containing alloy. Small size second phase particles Mg2Sn were observed to form in the Sn-containing alloy and distribute in the fine dimples of fracture surface. These features of microstructure were believed to impart higher strength and fracture toughness of the Sn-containing alloy on overaging.

Microstructure and Properties of Zirconia-Mullite Nanocomposites Obtained from Si-Al-Zr-O Amorphous Bulks Doped with CaO and MgO

2011 ◽  
Vol 142 ◽  
pp. 87-91 ◽  
Author(s):  
Xiao Ping Tan ◽  
Shu Quan Liang ◽  
Li Yuan Chai
Keyword(s):  
Electron Microscopy ◽  
Fracture Toughness ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Thermal Treatment ◽  
Anisotropic Growth ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Zirconia-mullite nanocomoposites were prepared from Si-Al-Zr-O amorphous bulk with diffrent content of CaO and MgO by two-step thermal treatment between 900 and 1200°C. The effects of the additives on the phase and microsturcture were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). The results show that the addition of CaO promotes cristobalite phase formation and the anisotropic growth of mullite grains. An indention micro-crack method was used to measure the fracture toughness of zirconia-mullite nanocomoposites. The results demonstrate that the fracture toughness increases with higher concentration of CaO. The improvement of fracture toughness is attributed to the anisotropic growth of grains.

Ageing Processes of Li-Containing Al-Zn-Mg-Cu Alloys

2007 ◽  
Vol 353-358 ◽  
pp. 1605-1608 ◽  
Author(s):  
Zhong Kui Zhao ◽  
Tie Tao Zhou ◽  
Pei Ying Liu ◽  
Chang Qi Chen
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Grain Boundary ◽  
Coarse Grain ◽  
Precipitate Free Zone ◽  
Free Zone ◽  
Cu Alloys ◽  
Transmission Electron ◽  
Ageing Processes ◽  
Two Peaks

1.1%Li was added to 7075 alloys to obtain the Li-containing Al-Zn-Mg-Cu alloys. The microstructure and hardness of the alloys are investigated by transmission electron microscopy (TEM) and Vickers hardness. The hardness of the single-aged alloys is low. When the alloys were double-aged or multi-aged, the hardness is comparable to that of Al-Zn-Mg-Cu alloys at peak ageing. Two peaks were present in the hardness curves of the multi-aged Li-containing Al-Zn-Mg-Cu alloys. With the last-step temperature increases, two-peak phenomenon becomes prominent. The density and size of precipitates are influenced remarkedly by the ageing processes. Coarse grain boundary precipitates and PFZ (precipitate free zone)can be observed when the Li-containing Al-Zn-Mg-Cu alloys were multi-aged, and the higher the last-step ageing temperature, the wider the PFZ is.

Ultrastructural Analysis of the Salivary Glands of Gromphadorhina Portentosa (Schaum)

1977 ◽  
Vol 35 ◽  
pp. 638-639
Author(s):  
P.J. Dailey
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Salivary Glands ◽  
Secretory Vesicles ◽  
The Past ◽  
Transmission Electron ◽  
Means Of Transmission ◽  
Gromphadorhina Portentosa ◽  
Scanning Electron ◽  
Topographical Relief

The structure of insect salivary glands has been extensively investigated during the past decade; however, none have attempted scanning electron microscopy (SEM) in ultrastructural examinations of these secretory organs. This study correlates fine structure by means of SEM cryofractography with that of thin-sectioned epoxy embedded material observed by means of transmission electron microscopy (TEM).Salivary glands of Gromphadorhina portentosa were excised and immediately submerged in cold (4°C) paraformaldehyde-glutaraldehyde fixative1 for 2 hr, washed and post-fixed in 1 per cent 0s04 in phosphosphate buffer (4°C for 2 hr). After ethanolic dehydration half of the samples were embedded in Epon 812 for TEM and half cryofractured and subsequently critical point dried for SEM. Dried specimens were mounted on aluminum stubs and coated with approximately 150 Å of gold in a cold sputtering apparatus.Figure 1 shows a cryofractured plane through a salivary acinus revealing topographical relief of secretory vesicles.

Two- or three-way observations of the identical cell elements within the same sections by LM, TEM and/or SEM

1978 ◽  
Vol 36 (2) ◽  
pp. 82-83 ◽  
Author(s):  
Nakazo Watari ◽  
Yasuaki Hotta ◽  
Yoshio Mabuchi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Fine Structure ◽  
Light Microscopy ◽  
Thin Sections ◽  
Transmission Electron ◽  
Identical Cell ◽  
Electron Microscopes ◽  
Scanning Electron

It is very useful if we can observe the identical cell elements within the same sections by light microscopy (LM), transmission electron microscopy (TEM) and/or scanning electron microscopy (SEM) sequentially, because, the cell fine structure can not be indicated by LM, while the color is; on the other hand, the cell fine structure can be very easily observed by EM, although its color properties may not. However, there is one problem in that LM requires thick sections of over 1 μm, while EM needs very thin sections of under 100 nm. Recently, we have developed a new method to observe the same cell elements within the same plastic sections using both light and transmission (conventional or high-voltage) electron microscopes.In this paper, we have developed two new observation methods for the identical cell elements within the same sections, both plastic-embedded and paraffin-embedded, using light microscopy, transmission electron microscopy and/or scanning electron microscopy (Fig. 1).

Scanning and Transmission Microscopy of Nematocyst Batteries in Epitheliomuscular Cells of Hydra

1971 ◽  
Vol 29 ◽  
pp. 410-411 ◽  
Author(s):  
Jane A. Westfall ◽  
S. Yamataka ◽  
Paul D. Enos
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Osmium Tetroxide ◽  
External Surface ◽  
Three Dimensional ◽  
Surface Structures ◽  
Transmission Microscopy ◽  
Transmission Electron ◽  
Freeze Dried ◽  
Scanning Electron

Scanning electron microscopy (SEM) provides three dimensional details of external surface structures and supplements ultrastructural information provided by transmission electron microscopy (TEM). Animals composed of watery jellylike tissues such as hydras and other coelenterates have not been considered suitable for SEM studies because of the difficulty in preserving such organisms in a normal state. This study demonstrates 1) the successful use of SEM on such tissue, and 2) the unique arrangement of batteries of nematocysts within large epitheliomuscular cells on tentacles of Hydra littoralis.Whole specimens of Hydra were prepared for SEM (Figs. 1 and 2) by the fix, freeze-dry, coat technique of Small and Màrszalek. The specimens were fixed in osmium tetroxide and mercuric chloride, freeze-dried in vacuo on a prechilled 1 Kg brass block, and coated with gold-palladium. Tissues for TEM (Figs. 3 and 4) were fixed in glutaraldehyde followed by osmium tetroxide. Scanning micrographs were taken on a Cambridge Stereoscan Mark II A microscope at 10 KV and transmission micrographs were taken on an RCA EMU 3G microscope (Fig. 3) or on a Hitachi HU 11B microscope (Fig. 4).

Application of Scanning Electron Microscopy to Medical Research

1969 ◽  
Vol 27 ◽  
pp. 12-13
Author(s):  
J. D. Hutchison
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Medical Research ◽  
Prosthetic Heart Valve ◽  
School Of Medicine ◽  
Transmission Electron ◽  
Definition Of ◽  
Mechanism Of Failure ◽  
The Brain ◽  
Scanning Electron

When the transmission electron microscope was commercially introduced a few years ago, it was heralded as one of the most significant aids to medical research of the century. It continues to occupy that niche; however, the scanning electron microscope is gaining rapidly in relative importance as it fills the gap between conventional optical microscopy and transmission electron microscopy.IBM Boulder is conducting three major programs in cooperation with the Colorado School of Medicine. These are the study of the mechanism of failure of the prosthetic heart valve, the study of the ultrastructure of lung tissue, and the definition of the function of the cilia of the ventricular ependyma of the brain.

A Comparative Study of Fractographic Replicas

1974 ◽  
Vol 32 ◽  
pp. 566-567
Author(s):  
Loren Anderson ◽  
Pat Pizzo ◽  
Glen Haydon
Keyword(s):  
Electron Microscopy ◽  
Electron Microscopic Examination ◽  
Direct Examination ◽  
Electron Microscopic ◽  
Reliable Technique ◽  
Service Failures ◽  
Transmission Electron ◽  
Mode Of Failure ◽  
Scanning Electron Microscopic ◽  
Scanning Electron

Transmission electron microscopy of replicas has long been used to study the fracture surfaces of components which fail in service. Recently, the scanning electron microscope (SEM) has gained popularity because it allows direct examination of the fracture surface. However, the somewhat lower resolution of the SEM coupled with a restriction on the sample size has served to limit the use of this instrument in investigating in-service failures. It is the intent of this paper to show that scanning electron microscopic examination of conventional negative replicas can be a convenient and reliable technique for determining mode of failure.

Sign in / Sign up

Export Citation Format

Share Document