Impact and Thermal Properties of Unsaturated Polyester (UPR) Composites Filled with Empty Fruit Bunch Palm Oil (EFBPO) and Cellulose

2014 ◽  
Vol 896 ◽  
pp. 310-313 ◽  
Author(s):  
Elmer Surya ◽  
Michael ◽  
Halimatuddahliana ◽  
Maulida
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Palm Oil ◽  
Impact Test ◽  
Unsaturated Polyester ◽  
Empty Fruit Bunch ◽  
Infra Red ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

In this research, the impact properties of unsaturated polyester (UPR) composites filled with empty fruit bunch palm oil (EFBPO) and cellulose were investigated. The composites were made by hand-lay up method by mixing UPR with the content of each fillers (EFBPO and cellulose) of 5,10,15,20 wt.%. The parameter which was carried out on the prepared samples was impact test. It was found that the addition of fillers to the matrix caused the impact strength of composites increased at 10% addition of EFBPO and 5% addition of cellulose. The results were confirmed by fourier transform infra-red (FTIR) and supported by thermogravimetric analysis (TGA) and scanning electron microscopy (SEM).

Tensile Property of the Flax/Polyester Composites after Water Treatment

2011 ◽  
Vol 194-196 ◽  
pp. 1740-1744 ◽  
Author(s):  
Qiu Hong Wang ◽  
Gu Huang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Water Treatment ◽  
Tensile Property ◽  
Unsaturated Polyester ◽  
Water Immersion ◽  
The Matrix ◽  
Polyester Composites ◽  
Scanning Electron

Flax fabric was woven and composites were produced by using the VARI technique with flax fabric as the reinforcement and unsaturated polyester as the matrix. Laminates with two, three and four layers were fabricated respectively. After saturated in the water for different durations of time (7, 14, 21 and 30 days), the tensile strength of the composites was tested. After being soaked in the water for 7, 14 and 21 days, the tensile strength of the two-layer composites was decreased. For the three and four layers specimens, the tensile strength was increased initially with water treatment for 7 and 14 days,and decreased for 21 and 30 days. Scanning electron microscopy (SEM) confirmed that it might be contributed to the thickness of the two-layer composites. The thinner specimen is easier to be damaged by the penetrated moisture owing to the delamination between the fiber and the matrix after water immersion. For the three and four layers specimens, their contradictory tensile strength suggests that the thicker specimen can delay the moisture permeation and is of better water durability.

The Impact Properties of a Polyurethane Composite Filled with Clay

2011 ◽  
Vol 197-198 ◽  
pp. 1100-1103
Author(s):  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Analysis ◽  
Impact Testing ◽  
Impact Properties ◽  
Polyurethane Composite ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

A polyurethane/clay (PU/clay) composite was synthesized. The microstructure of the composite was examined by scanning electron microscopy. The impact properties of the composite were characterized by impact testing. The study on the structure of the composite showed that clays could be dispersed in the polymer matrix well apart from a few of clusters. The results from mechanical analysis indicated that the impact properties of the composite were increased greatly in comparison with pure polyurethane. The investigation on the mechanical properties showed that the impact strength could be obviously increased by adding 20 wt% (by weight) clay to the matrix.

Effect of inorganic nanofillers on the impact behavior and fracture probability of industrial high-density polyethylene nanocomposite

2017 ◽  
Vol 52 (18) ◽  
pp. 2431-2442 ◽  
Author(s):  
Harun Sepet ◽  
Necmettin Tarakcioglu ◽  
RDK Misra
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Density Polyethylene ◽  
Fracture Probability ◽  
High Density ◽  
Impact Behavior ◽  
Inorganic Filler ◽  
Melt Mixing ◽  
The Impact ◽  
Scanning Electron

The main purpose of this work is to study how the morphology of nanofillers and dispersion and distribution level of inorganic nanofiller influence the impact behavior and fracture probability of inorganic filler filled industrial high-density polyethylene nanocomposites. For this study, nanoclay and nano-CaCO3 fillers–high-density polyethylene mixings (0, 1, 3, 5 wt.% high-density polyethylene) was prepared by melt-mixing method using a compounder system. The impact behavior was examined by charpy impact test, scanning electron microscopy, and probability theory and statistics. The level of the dispersion was characterized with scanning electron microscopy energy dispersive X-ray spectroscopy analysis. The results showed rather good dispersion of both of inorganic nanofiller, with a mixture of exfoliated and confined morphology. The results indicated that the impact strength of the industrial nanocomposite decreased with the increase of inorganic particulate content. The impact reliability of the industrial nanocomposites depends on the type of nanofillers and their dispersion and distribution in the matrix.

Characteristics of Ni–Cr–Fe laser clad layers on EA4T steel

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744031
Author(s):  
Wenjing Chen ◽  
Hui Chen ◽  
Yongjing Wang ◽  
Congchen Li ◽  
Xiaoli Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cladding Layer ◽  
Metallurgical Bonding ◽  
The Matrix ◽  
Feeding Speed ◽  
Upper Bainite ◽  
Scanning Electron

The Ni–Cr–Fe metal powder was deposited on EA4T steel by laser cladding technology. The microstructure and chemical composition of the cladding layer were analyzed by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The bonding ability between the cladding layer and the matrix was measured. The results showed that the bonding between the cladding layer and the EA4T steel was metallurgical bonding. The microstructure of cladding layer was composed of planar crystals, columnar crystals and dendrite, which consisted of Cr2Ni3, [Formula: see text] phase, M[Formula: see text]C6 and Ni3B phases. When the powder feeding speed reached 4 g/min, the upper bainite occurred in the heat affected zone (HAZ). Moreover, the tensile strength of the joint increased, while the yield strength and the ductility decreased.

scholarly journals The Influence of A Mo Addition on the Interfacial Morphologies and Corrosion Resistances of Novel Fe-Cr-B Alloys Immersed in Molten Aluminum

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 256 ◽  
Author(s):  
Zicheng Ling ◽  
Weiping Chen ◽  
Weiye Xu ◽  
Xianman Zhang ◽  
Tiwen Lu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electron Probe ◽  
Molten Aluminum ◽  
Dendritic Structure ◽  
H13 Steel ◽  
X Ray ◽  
Transmission Electron ◽  
The Matrix ◽  
Scanning Electron

The influence of a Mo addition on the interfacial morphologies and corrosion resistances of novel Fe-Cr-B alloys in molten aluminum at 750 °C was systematically investigated using scanning electron microscopy, X-ray diffractometer, electron probe microanalysis, and transmission electron microscopy. The results indicated that Mo could not only strengthen the matrix but also facilitate the formation of borides. Furthermore, the microstructures of Mo-rich M2B boride changed from a local eutectic net-like structure to a typical coarse dendritic structure and a blocky hypereutectic structure with increasing Mo addition. This was true of the blocky Mo-rich M2B boride, rod-like Cr-rich M2B boride and the corrosion products, which had a synergistic effect on retarding of the diffusion of molten aluminum. Notably, the corrosion resistance of the Fe-Cr-B-Mo alloy, with an 8.3 wt.% Mo addition, was 3.8 times higher than that of H13 steel.

scholarly journals Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5734
Author(s):  
Paulina Kosmela ◽  
Jan Suchorzewski ◽  
Krzysztof Formela ◽  
Paweł Kazimierski ◽  
Józef Tadeusz Haponiuk ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Baltic Sea ◽  
Thermal Insulation ◽  
Reference Sample ◽  
Microcomputed Tomography ◽  
Polyurethane Foams ◽  
Relationship Of ◽  
The Impact ◽  
Scanning Electron

In this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume, area, shape and orientation on appearance density and thermal insulation properties of polyurethane foams was determined. The results presented in the paper confirm that microcomputed tomography is a useful tool for relatively quick estimation of polyurethane foams’ microstructure, what is crucial especially in the case of thermal insulation materials.

scholarly journals Effects of Droplet-Vitrification Cryopreservation Based on Physiological and Antioxidant Enzyme Activities ofBrassidiumShooting Star Orchid

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Safrina Rahmah ◽  
Safiah Ahmad Mubbarakh ◽  
Khor Soo Ping ◽  
Sreeramanan Subramaniam
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Liquid Nitrogen ◽  
Enzyme Activities ◽  
Structural Changes ◽  
Total Soluble Protein ◽  
Antioxidant Enzyme Activities ◽  
Droplet Vitrification ◽  
The Impact ◽  
Scanning Electron

Protocorm-like bodies (PLBs) ofBrassidiumShooting Star orchid were successfully cryopreserved using droplet-vitrification method. Vitrification based cryopreservation protocol is comprised of preculture, osmoprotection, cryoprotection, cooling, rewarming, and growth recovery and each and every step contributes to the achievement of successful cryopreservation. In order to reveal the lethal and nonlethal damage produced by cryopreservation, histological observation, scanning electron microscopy (SEM), and biochemical analysis were carried out in both cryopreserved and noncryopreserved PLBs ofBrassidiumShooting Star orchid comparing with the control PLBs stock culture. Histological and scanning electron microscopy analyses displayed structural changes in cryopreserved PLBs due to the impact of cryoinjury during exposure to liquid nitrogen. Total soluble protein significantly increased throughout the dehydration process and the highest value was achieved when PLBs were stored in liquid nitrogen. Ascorbate peroxidase (APX) and catalase (CAT) showed the highest enzyme activities in both dehydration and cryostorage treatments indicating that stress level of PLBs was high during these stages.

Microstructural Characterisation by Scanning Electron Microscopy of Spray Formed Al/SiCp Matrix Composite

2005 ◽  
Vol 498-499 ◽  
pp. 251-257 ◽  
Author(s):  
E.G. Gomes ◽  
J.L. Rossi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Volume Fraction ◽  
Spray Forming ◽  
Heat Treated ◽  
The Matrix ◽  
Microstructural Characterisation ◽  
Silicon Carbide Particles ◽  
Carbide Particles ◽  
Scanning Electron

The material used in this work was produced by spray forming AA7475 aluminium alloy and co-depositing silicon carbide particles (20% volume fraction). The spray formed composite billets were hot extruded into round bars. The microstructure was examined in the as received and heat treated (annealed, aged, and overaged) conditions by scanning electron microscopy. Scanning electron microscopy revealed an extensive Mg2Si phase precipitation at the Al/SiCp interface due probably to Mg segregation from the matrix to the interface, during the heat treatments.

Influence of Injection Conditions on the Mechanical Property of MWCNTs/ PC Nanocomposites

2014 ◽  
Vol 983 ◽  
pp. 94-98 ◽  
Author(s):  
Li Jun Wang ◽  
Jian Hui Qiu ◽  
Eiichi Sakai
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Property ◽  
Bending Strength ◽  
Surface Hardness ◽  
Interfacial Interaction ◽  
Multiwalled Carbon ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

The melting mixing was applied in the preparation of Multiwalled carbon nanotubes/Polycarbonate (MWCNTs/PC) nanocomposites. MWCNTs/PC nanocomposites with different MWCNTs contents were prepared under different injection conditions. The mechanical property of nanocomposites was comparatively investigated. The results demonstrated that: the tensile property of the nanocomposites was slightly improved by MWCNTs content increasing; but as the MWCNTs contents went on to increase to 10wt%, the tensile strength and bending strength were obviously decreased about 35% and 47%, respectively, but the impact strength and hardness were increased. The center hardness of MWCNTs/PC nanocomposites was greater than the surface hardness. Besides, the changes on the mechanical properties of the nanocomposites were studies by changing the injection conditions. By Scanning Electron Microscopy (SEM) observation, the microstructure and morphology of nanocomposites were analyzed, revealing that the center of the nanocomposite distributed more MWNTs, and the injection conditions would affect the MWNTs’ dispersion in the matrix and the interfacial interaction between MWCNTs and PC.

Sign in / Sign up

Export Citation Format

Share Document