A Composite Consisting of a Set of Hexagonal Ceramic Bars - The Numerical Study of the Ballistic Resistance

2011 ◽  
Vol 471-472 ◽  
pp. 1142-1146 ◽  
Author(s):  
Sebastian Stanislawek ◽  
Andrzej Morka ◽  
Tadeusz Niezgoda
Keyword(s):  
Reference Model ◽  
Numerical Study ◽  
Rigid Wall ◽  
Material Behavior ◽  
Aluminum Plate ◽  
Three Dimension ◽  
Projectile Impact ◽  
Ballistic Resistance ◽  
Behavior Simulation ◽  
The Impact

The paper presents a numerical study of a double layer composite panels impacted by a AP (Armor Piercing) 51WC projectile. The standard panel is built with aluminum and Al2O3 ceramic continuum layers while the studied model consists of the same aluminum plate but the front one is built with a set of hexagonal ceramic bars. The bar width and the impact position influence on the ballistic resistance are analyzed and compared with the reference solution. The problem has been solved with the usage of the modeling and simulation methods as well as finite elements method implemented in LS-DYNA software. Space discretization for each option was built by three dimension elements guarantying satisfying accuracy of the calculations. For material behavior simulation specific models including the influence of the strain rate and temperature changes were considered. Projectile Tungsten Curbide and aluminum plate material were described by Johnson-Cook model and ceramic target by Johnson-Holmquist model. In the studied panels the area surrounding back edges was supported by a rigid wall. The obtained results show interesting properties of the examined structures considering their ballistic resistance. All tests has given clear results about ballistic protection panel response under WC projectile impact. Panels consisting of sets of hexagonal ceramic bars are slightly easier to penetrate, reference model is stronger by 19% for smaller bars and by only 7% for bigger rods. Despite this fact, the ceramic layer is much less susceptible to overall destruction what makes it more applicable for the armor usage. Furthermore, little influence of the projectile impact point and consequently a part of the bar which is first destroyed is proved.

Multisphere Ceramic Composite Concept and its Numerical Study of the Ballistic Response

2011 ◽  
Vol 471-472 ◽  
pp. 1136-1141 ◽  
Author(s):  
Sebastian Stanislawek ◽  
Andrzej Morka ◽  
Tadeusz Niezgoda
Keyword(s):  
Reference Model ◽  
Numerical Study ◽  
Rigid Wall ◽  
Material Behavior ◽  
Material Strength ◽  
Three Dimension ◽  
Sphere Surface ◽  
Convex Shape ◽  
Behavior Simulation ◽  
The Impact

Numerical investigations were performed to determine the influence of the spherical convex shape ceramic - alumina composite in reference to the standard double layer panel. All versions of the target were verified in an impact test including influence upon the position of the AP (Armor Piercing) 7,62x51HHS impact. The crucial parameter which was used for this verification was change in time of the PROJECTILE kinetic energy. The problem has been solved with the usage of the modeling and simulation methods as well as finite elements method implemented in LS-DYNA software. Space discretization for each option was built by three dimension elements guarantying satisfying accuracy of the calculations. For material behavior simulation specific models including the influence of the strain rate and temperature changes were considered. Projectile’s core made of HHS and aluminum plate material were described by Johnson-Cook model and ceramic target with Johnson-Holmquist model. In the studied panels the area surrounding back edges was supported by rigid wall. The obtained results show interesting properties of the new structures considering their ballistic resistance. However only certain places were chosen for tests, the protection ability against projectile attack is in general higher than the reference model. What is particularly interesting during the 6.6mm from the sphere center impact the sphere surface trajectory deviation effect is present. A projectile is not stopped here by material strength but the front layer shape. Moreover it can be assumed that this phenomenon will take place on majority of points on the sphere surface. Despite this fact, a ceramic multi sphere layer is less susceptible to overall destruction, depending on the impact point. The results of those numerical simulations can be used for designing of modern armor protection systems against hard kinetic projectiles.

scholarly journals Pyramidal ceramic armor ability to defeat projectile threat by changing its trajectory

2015 ◽  
Vol 63 (4) ◽  
pp. 843-849 ◽  
Author(s):  
S. Stanislawek ◽  
A. Morka ◽  
T. Niezgoda
Keyword(s):  
Numerical Study ◽  
Three Dimensional ◽  
Alloy Layer ◽  
Material Behavior ◽  
Composite Panel ◽  
Reference Structure ◽  
Temperature Changes ◽  
Behavior Simulation ◽  
Space Discretization ◽  
The Impact

Abstract This paper presents a numerical study of a multilayer composite panel impacted by an AP (Armor Piercing) 14.5×114 mm B32 projectile. The composite consists of alternating layers of hard ceramic and a ductile aluminum alloy. While the alloy layer consists of typical plate, ceramics confront projectiles in the form of ceramic pyramids. The studied models are compared with a reference structure, which is a standard double layer panel. The problem has been solved with the usage of modeling and simulation methods as well as a finite elements method implemented in LS-DYNA software. Space discretization for each option was built with three dimensional elements ensuring satisfying accuracy of the calculations. For material behavior simulation, specific models including the influence of the strain rate and temperature changes were considered. A steel projectile and aluminum plate material were described by the Johnson-Cook model and a ceramic target by the Johnson-Holmquist model. The obtained results indicate that examined structures can be utilized as a lightweight ballistic armor in certain conditions. However, panels consisting of sets of ceramic prisms are a little easier to penetrate. Despite this fact, a ceramic layer is much less susceptible to overall destruction, making it more applicable for the armor usage. What is most important in this study is that significant projectile trajectory deviation is detected, depending on the impact point. Such an effect may be utilized in solutions, where a target is situated relatively far from an armor.

Numerical Study on the Anti-Ballistic Properties of Metal Encapsulating Ceramic Composite Armors

2015 ◽  
Vol 723 ◽  
pp. 26-30 ◽  
Author(s):  
Jiang Ren Lu ◽  
Xin Li Sun ◽  
Xing Hui Cai ◽  
San Qiang Dong ◽  
Guo Liang Wang
Keyword(s):  
Ceramic Composite ◽  
Numerical Study ◽  
Three Dimensional ◽  
Ceramic Block ◽  
Ballistic Resistance ◽  
Limit Velocity ◽  
Ballistic Properties ◽  
Ballistic Limit Velocity ◽  
The Impact ◽  
Two Hybrid

The impact responses and ballistic resistance of the metal encapsulating ceramic composite armors with same area density and two hybrid cores are investigated. The hybrid cores include square metallic lattice with ceramic block insertions, and square metallic lattice with ceramic ball insertions and void-filling epoxy resin. Three-dimensional (3D) finite element (FE) simulations are carried out for each composite armors impacted by bullet with 12.7mm diameter. The focus is placed on the energy absorption capabilities and ballistic limit velocity of different composite armors. Results indicate that two kind of armors can improve the ballistic resistance properties and save mass of 22% and 25% compared to the homogeneous 4340 steel, respectively.

Simulation of projectile impact on steel plate-lined, reinforced concrete panels using the smooth particle hydrodynamics formulation

2021 ◽  
pp. 204141962110420
Author(s):  
Brian Terranova ◽  
Len Schwer ◽  
Andrew Whittaker
Keyword(s):  
Reinforced Concrete ◽  
Steel Plate ◽  
Numerical Study ◽  
Material Model ◽  
Projectile Impact ◽  
Concrete Panels ◽  
Back Face ◽  
Steel Liner ◽  
Observed Damage ◽  
The Impact

Data from the Tsubota et al. (1993) experiments provided the basis for a numerical study that investigated the impact response of steel-plate lined, reinforced concrete panels using the SPH formulation in LS-DYNA. The simulated tests involved 50 mm (1.97 in), 70 mm (2.76 in), and 90 mm (3.54 in) thick reinforced concrete (RC) panels with steel liners and one 50-mm thick benchmark RC panel. Three of the five panels had a steel liner attached to the back face and one had a steel liner on both faces. The panels were normally impacted by a 39.6 mm (1.56 in) diameter projectile at a velocity of 170 m/s (6693 in/s). Reasonable predictions of observed damage, including perforation, liner fracture or bulging, and concrete scabbing were achieved using the MAT072R3 concrete material model. The effectiveness of adding steel liners to a concrete panel to prevent perforation and scabbing resulting from projectile impact was investigated using the numerical model and MAT072R3. Installing a steel liner on the back face of a panel, with a reinforcement ratio equal to that of the internal reinforcement, is an effective method to mitigate scabbing but has little effect on perforation resistance.

Impact behaviour of elastoplastic spheres with a rigid wall

2000 ◽  
Vol 214 (8) ◽  
pp. 1107-1114 ◽  
Author(s):  
L-Y Li ◽  
C Thornton ◽  
C-Y Wu
Keyword(s):  
Contact Force ◽  
Numerical Study ◽  
Rigid Wall ◽  
Coefficient Of Restitution ◽  
Two Dimensional ◽  
Material Behaviour ◽  
Normal Impact ◽  
Dimensional Finite Element ◽  
The Impact ◽  
Force Displacement

The paper presents a numerical study of the normal impact of elastoplastic spheres with a rigid wall. The analysis is performed by employing DYNA2D, a non-linear, explicit, two-dimensional finite element (FE) code for impact mechanics. Deformations, time evolution of the contact force and contact force-displacement relationships during the impact are presented. Influences of material behaviour are discussed and their effect on the coefficient of restitution is also demonstrated.

Parametric Study of the Effect of Hinged Connectors on the Behavior of Origami-Inspired Structures Comprised of Sandwich Panels

2015 ◽  
Author(s):  
Zach C. Ballard ◽  
Ashley P. Thrall ◽  
Brian J. Smith
Keyword(s):  
Parametric Study ◽  
Numerical Study ◽  
Sandwich Panels ◽  
Rigid Wall ◽  
Fiber Reinforced Polymer ◽  
Structural Performance ◽  
Uniform Load ◽  
Reinforced Polymer ◽  
Relative Placement ◽  
The Impact

Origami can be a source of inspiration for rapidly deployable, rigid wall shelters. Folding panels comprised of sandwich panels will result in a lightweight, transportable design. The design of connections between panels is critical to the overall structural performance, but can pose a major design challenge. This paper investigates the implementation of hinges for connections between panels. A single panel, comprised of fiber-reinforced polymer faces and a foam core, is restrained by aluminum hinged connectors and subjected to a uniform load. An exhaustive parametric study is performed using a numerical model previously validated by experimental data. The numerical study will facilitate better understanding of the impact of the 1) number, 2) size, and 3) relative placement of connectors on panel behavior, with data comparisons focusing on the longitudinal surface strains and displacements of the panel. This investigation culminates in a set of guidelines for hinged connectors in origami-inspired structures.

Parametric study of aluminum bar shearing using Johnson-Cook material modeling

2021 ◽  
pp. 095440542199562
Author(s):  
Sonda Moakhar ◽  
Hamdi Hentati ◽  
Maher Barkallah ◽  
Jamel Louati ◽  
Mohamed Haddar
Keyword(s):  
Stress State ◽  
Shear Rate ◽  
High Speed ◽  
Surface Defects ◽  
Numerical Study ◽  
Ductile Failure ◽  
Material Behavior ◽  
Surface Geometry ◽  
Shear Surface ◽  
The Impact

Previous studies of the shearing process demonstrated that clearance and shear rate are the most influential parameters on the geometry of sheared billets. This paper illustrates a parametric numerical study of the impact of these parameters on the quality of the shear surface using the finite element simulation of shearing. In order to account for interactions between stress state evolution and the associated heating during shearing, a fully coupled thermo-mechanical simulation method was adopted. The influence of stress state, strain rate, and temperature on the material behavior were taken into account by using Johnson-Cook plasticity and ductile failure models. Many simulations were carried out involving diverse shear rates and shear clearances. The relationship between the parameters of shear surface geometry and the temperature was illustrated and proven. Contrary to the expectation of high-speed shearing performance, a burr free smooth shear surface was found using a low shear rate. This study illustrates a numerical strategy to determine the best shear clearance-rate set for aluminum alloy Al7075-T6 bars that minimizes the shear surface defects.

scholarly journals Experimental and Numerical Study of Ballistic Resistance of Composites Based on Sandwich Metallic Foams

2021 ◽  
Author(s):  
Anna Dmitruk ◽  
Krzysztof Naplocha ◽  
Joanna Pach ◽  
Dariusz Pyka ◽  
Grzegorz Ziółkowski ◽  
...  
Keyword(s):  
Impact Load ◽  
Numerical Study ◽  
Absorption Capacity ◽  
Polymer Materials ◽  
Metallic Foams ◽  
Ballistic Resistance ◽  
Polyurethane Resin ◽  
Computed Microtomography ◽  
Ct System ◽  
The Impact

AbstractIn recent years, hybrid composite materials are of increasing interest during the search for new materials to be used as ballistic barriers (shields) and kinetic energy absorbers. The main objective of this study is to test the energy absorption capacity of Zn-Al alloys filled with various polymer materials (epoxy resin, polyurethane resin and silicone). The ballistic resistance of modern hybrid materials to direct firing of a 5.56 × 45 mm SS109 projectile and during quasi-static piercing test is examined. Next, a numerical simulation in the ABAQUS environment is performed. In order to accurately reproduce the foam structure, a computed microtomography (CT) system is used. In the simulation of deformations of viscoplastic bodies, the Lagrange and Smoothed Particle Hydrodynamic (SPH) methods are applied. The obtained results from numerical analyses are verified with experimental results. Metallic foams are proven to have only a remote influence on the impact load, while, when filled with polyurethane resin, they show resistance to the overshoot. Performed simulation supports the detailed analysis of the impact energy dissipation for each of the samples.

scholarly journals Model of thermal buoyancy in cavity-ventilated roof constructions

2021 ◽  
pp. 174425912098418
Author(s):  
Toivo Säwén ◽  
Martina Stockhaus ◽  
Carl-Eric Hagentoft ◽  
Nora Schjøth Bunkholt ◽  
Paula Wahlgren
Keyword(s):  
Analytical Model ◽  
Flow Rate ◽  
Numerical Study ◽  
Air Flow ◽  
Wind Pressure ◽  
Air Flow Rate ◽  
Test Set ◽  
Air Cavity ◽  
Thermal Buoyancy ◽  
The Impact

Timber roof constructions are commonly ventilated through an air cavity beneath the roof sheathing in order to remove heat and moisture from the construction. The driving forces for this ventilation are wind pressure and thermal buoyancy. The wind driven ventilation has been studied extensively, while models for predicting buoyant flow are less developed. In the present study, a novel analytical model is presented to predict the air flow caused by thermal buoyancy in a ventilated roof construction. The model provides means to calculate the cavity Rayleigh number for the roof construction, which is then correlated with the air flow rate. The model predictions are compared to the results of an experimental and a numerical study examining the effect of different cavity designs and inclinations on the air flow rate in a ventilated roof subjected to varying heat loads. Over 80 different test set-ups, the analytical model was found to replicate both experimental and numerical results within an acceptable margin. The effect of an increased total roof height, air cavity height and solar heat load for a given construction is an increased air flow rate through the air cavity. On average, the analytical model predicts a 3% higher air flow rate than found in the numerical study, and a 20% lower air flow rate than found in the experimental study, for comparable test set-ups. The model provided can be used to predict the air flow rate in cavities of varying design, and to quantify the impact of suggested roof design changes. The result can be used as a basis for estimating the moisture safety of a roof construction.

scholarly journals Numerical Simulation of the Impact of the Heat Source Position on Melting of a Nano-Enhanced Phase Change Material

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1425
Author(s):  
Tarek Bouzennada ◽  
Farid Mechighel ◽  
Kaouther Ghachem ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Melting Rate ◽  
Heat Transfer Fluid ◽  
Commercial Code ◽  
Tube Position ◽  
The Impact ◽  
Change Material

A 2D-symmetric numerical study of a new design of Nano-Enhanced Phase change material (NEPCM)-filled enclosure is presented in this paper. The enclosure is equipped with an inner tube allowing the circulation of the heat transfer fluid (HTF); n-Octadecane is chosen as phase change material (PCM). Comsol-Multiphysics commercial code was used to solve the governing equations. This study has been performed to examine the heat distribution and melting rate under the influence of the inner-tube position and the concentration of the nanoparticles dispersed in the PCM. The inner tube was located at three different vertical positions and the nanoparticle concentration was varied from 0 to 0.06. The results revealed that both heat transfer/melting rates are improved when the inner tube is located at the bottom region of the enclosure and by increasing the concentration of the nanoparticles. The addition of the nanoparticles enhances the heat transfer due to the considerable increase in conductivity. On the other hand, by placing the tube in the bottom area of the enclosure, the liquid PCM gets a wider space, allowing the intensification of the natural convection.

Sign in / Sign up

Export Citation Format

Share Document